Duane Model: Difference between revisions

From ReliaWiki
Jump to navigation Jump to search
No edit summary
 
(29 intermediate revisions by 6 users not shown)
Line 1: Line 1:
{{template:RGA BOOK|3|Duane}}
{{template:RGA BOOK|3.1|Duane}}
In 1962, J. T. Duane published a report in which he presented failure data of different systems during their development programs [[RGA_References|
In 1962, J. T. Duane published a report in which he presented failure data of different systems during their development programs [[RGA_References|
[8]]]. While analyzing the data, it was observed that the cumulative MTBF versus cumulative operating time followed a straight line when plotted on log-log paper, as shown next.  
[8]]]. While analyzing the data, it was observed that the cumulative MTBF versus cumulative operating time followed a straight line when plotted on log-log paper, as shown next.  


[[Image:rga4.1.png|center|500px|Cumulative MTBF vs. Cumulative Test Time postulated by Duane.]]
[[Image:rga4.1.png|center|450px|Cumulative MTBF vs. Cumulative Test Time postulated by Duane.]]


Based on that observation, Duane developed his model as follows. If <math>N(T)\,\!</math> is the number of failures by time <math>T\,\!</math> , the observed mean (average) time between failures, <math>MTB{{F}_{c}},\,\!</math> at time <math>T\,\!</math> is:   
Based on that observation, Duane developed his model as follows. If <math>N(T)\,\!</math> is the number of failures by time <math>T\,\!</math>, the observed mean (average) time between failures, <math>MTB{{F}_{c}},\,\!</math> at time <math>T\,\!</math> is:   


::<math>MTB{{F}_{c}}=\frac{T}{N(T)}</math>
:<math>MTB{{F}_{c}}=\frac{T}{N(T)}\,\!</math>


The equation of the line can be expressed as:  
The equation of the line can be expressed as:  


::<math>\begin{align}
:<math>\begin{align}
y=mx+c
y=mx+c
\end{align}</math>
\end{align}\,\!</math>


Setting:  
Setting:  


::<math>\begin{align}
:<math>\begin{align}
  y= & \ln (MTB{{F}_{c}}) \\  
  y= & \ln (MTB{{F}_{c}}) \\  
  x= & \ln (T) \\  
  x= & \ln (T) \\  
  m= & \alpha  \\  
  m= & \alpha  \\  
  c= & \ln b   
  c= & \ln b   
\end{align}</math>
\end{align}\,\!</math>


yields:
yields:


::<math>\begin{align}
:<math>\begin{align}
\ln (MTB{{F}_{c}})=\alpha \ln (T)+\ln b
\ln (MTB{{F}_{c}})=\alpha \ln (T)+\ln b
\end{align}</math>
\end{align}\,\!</math>


Then equating <math>MTB{{F}_{c}}\,\!</math> to its expected value, and assuming an exact linear relationship, gives:


Then equating  <math>MTB{{F}_{c}}\,\!</math>  to its expected value, and assuming an exact linear relationship, gives:
:<math>\begin{align}
 
::<math>\begin{align}
E(MTB{{F}_{c}})=b{{T}^{\alpha }}
E(MTB{{F}_{c}})=b{{T}^{\alpha }}
\end{align}</math>
\end{align}\,\!</math>


or:  
or:  


::<math>\begin{align}
:<math>\begin{align}
MTB{{F}_{c}}=b{{T}^{\alpha }}
MTB{{F}_{c}}=b{{T}^{\alpha }}
\end{align}</math>
\end{align}\,\!</math>


And, if you assume a constant failure intensity, then the cumulative failure intensity, <math>{{\lambda }_{c}}\,\!</math> , is:  
And, if you assume a constant failure intensity, then the cumulative failure intensity, <math>{{\lambda }_{c}}\,\!</math>, is:  


::<math>E({{\lambda }_{c}})=\frac{1}{b}{{T}^{-\alpha }}</math>
:<math>E({{\lambda }_{c}})=\frac{1}{b}{{T}^{-\alpha }}\,\!</math>


or:  
or:  


::<math>{{\widehat{{\bar{\lambda }}}}_{c}}=\frac{1}{b}{{T}^{-\alpha }}</math>
::<math>{{\hat{{\bar{\lambda }}}}_{c}}=\frac{1}{b}{{T}^{-\alpha }}\,\!</math>


Also, the expected number of failures up to time <math>T\,\!</math> is:  
Also, the expected number of failures up to time <math>T\,\!</math> is:  


::<math>\begin{align}
:<math>\begin{align}
   E(N(T))= & {{\widehat{{\bar{\lambda }}}}_{c}}\cdot T \\  
   E(N(T))= & {{\hat{{\bar{\lambda }}}}_{c}}\cdot T \\  
   = & \frac{1}{b}{{T}^{1-\alpha }}   
   = & \frac{1}{b}{{T}^{1-\alpha }}   
\end{align}</math>
\end{align}\,\!</math>


where:
where:


*<math>{{\widehat{{\bar{\lambda }}}}_{c}}\,\!</math> is the average estimate of the cumulative failure intensity, failures/hour.
*<math>{{\hat{{\bar{\lambda }}}}_{c}}\,\!</math> is the average estimate of the cumulative failure intensity, failures/hour.
*<math>T\,\!</math> is the total accumulated unit hours of test and/or development time.
*<math>T\,\!</math> is the total accumulated unit hours of test and/or development time.
*<math>1/b\,\!</math> is the cumulative failure intensity at <math>T = 1\,\!</math> or at the beginning of the test, or the earliest time at which the first <math>{{\widehat{{\bar{\lambda }}}}}\,\!</math> is predicted, or the <math>{{\widehat{{\bar{\lambda }}}}}\,\!</math> for the equipment at the start of the design and development process.
*<math>1/b\,\!</math> is the cumulative failure intensity at <math>T = 1\,\!</math> or at the beginning of the test, or the earliest time at which the first <math>{{\hat{{\bar{\lambda }}}}}\,\!</math> is predicted, or the <math>{{\hat{{\bar{\lambda }}}}}\,\!</math> for the equipment at the start of the design and development process.
*<math>\alpha\,\!</math>is the improvement rate in the <math>{{\widehat{{\bar{\lambda }}}}}, 0\le \alpha \le 1\,\!</math>.
*<math>\alpha\,\!</math>is the improvement rate in the <math>{{\hat{{\bar{\lambda }}}}}, 0\le \alpha \le 1\,\!</math>.


The corresponding <math>MTB{{F}_{c}}\,\!</math>, or <math>{{\hat{m}}_{c}}\,\!</math>, is equal to:


The corresponding  <math>MTB{{F}_{c}}\,\!</math> , or  <math>{{\hat{m}}_{c}}\,\!</math> , is equal to:
:<math>{{\hat{m}}_{c}}=b{{T}^{\alpha }}\,\!</math>


::<math>{{\hat{m}}_{c}}=b{{T}^{\alpha }}</math>
where <math>b=\,\!</math> cumulative MTBF at <math>T=1\,\!</math> or at the beginning of the test, or the earliest time at which the first <math>\hat{m}\,\!</math> can be determined, or the <math>\hat{m}\,\!</math> predicted at the start of the design and development process ( <math>b>0\,\!</math> ).


where  <math>b=\,\!</math> cumulative MTBF at  <math>T=1\,\!</math> or at the beginning of the test, or the earliest time at which the first  <math>\hat{m}\,\!</math> can be determined, or the  <math>\hat{m}\,\!</math> predicted at the start of the design and development process ( <math>b>0\,\!</math> ).
The cumulative MTBF, <math>{{\hat{m}}_{c}}\,\!</math>, and <math>{{\hat{{\bar{\lambda }}}}_{c}}\,\!</math> tell whether <math>m\,\!</math> is increasing or <math>\lambda \,\!</math> is decreasing with time, utilizing all data up to that time. You may want to know, however, the instantaneous <math>{{\hat{m}}_{i}}\,\!</math> or <math>{{\hat{{\bar{\lambda }}}}_{i}}\,\!</math> to see what you are doing at a specific instant or after a specific test and development time. The instantaneous failure intensity, <math>{{\lambda }_{i}}\,\!</math>, is:


The cumulative MTBF,  <math>{{\hat{m}}_{c}}\,\!</math> , and  <math>{{\widehat{{\bar{\lambda }}}}_{c}}\,\!</math>  tell whether  <math>m\,\!</math>  is increasing or  <math>\lambda \,\!</math>  is decreasing with time, utilizing all data up to that time. You may want to know, however, the instantaneous  <math>{{\hat{m}}_{i}}\,\!</math>  or  <math>{{\widehat{{\bar{\lambda }}}}_{i}}\,\!</math>  to see what you are doing at a specific instant or after a specific test and development time. The instantaneous failure intensity,  <math>{{\lambda }_{i}}\,\!</math> , is:
:<math>\begin{align}
 
::<math>\begin{align}
   {{\lambda }_{i}}= & \frac{d(E(N(T)))}{dT} \\  
   {{\lambda }_{i}}= & \frac{d(E(N(T)))}{dT} \\  
  = & \frac{1}{b}(1-\alpha ){{T}^{-\alpha }} \\  
  = & \frac{1}{b}(1-\alpha ){{T}^{-\alpha }} \\  
  = & (1-\alpha ){{\lambda }_{c}}   
  = & (1-\alpha ){{\lambda }_{c}}   
\end{align}</math>
\end{align}\,\!</math>


Similarly, using the equation for the expected number of failures up to time <math>T\,\!</math>, this procedure yields:
Similarly, using the equation for the expected number of failures up to time <math>T\,\!</math>, this procedure yields:


::<math>\begin{align}
:<math>\begin{align}
   {{m}_{i}}= & \frac{1}{1-\alpha }b{{T}^{\alpha }} \\  
   {{m}_{i}}= & \frac{1}{1-\alpha }b{{T}^{\alpha }} \\  
   = & \frac{1}{1-\alpha }{{{\hat{m}}}_{c}},:\ \ \alpha \not{=}1   
   = & \frac{1}{1-\alpha }{{{\hat{m}}}_{c}},:\ \ \alpha \not{=}1   
\end{align}</math>
\end{align}\,\!</math>


where <math>\alpha =1\,\!</math> implies infinite MTBF growth.
where <math>\alpha =1\,\!</math> implies infinite MTBF growth.


As shown in these derivations, the instantaneous failure intensity improvement line is obtained by shifting the cumulative failure intensity line down, parallel to itself, by a distance of <math>(1-\alpha )\,\!</math> . Similarly, the current or instantaneous MTBF growth line is obtained by shifting the cumulative MTBF line up, parallel to itself, by a distance of <math>\tfrac{1}{1-\alpha }\,\!</math> , as illustrated in the figure below.
As shown in these derivations, the instantaneous failure intensity improvement line is obtained by shifting the cumulative failure intensity line down, parallel to itself, by a distance of <math>(1-\alpha )\,\!</math>. Similarly, the current or instantaneous MTBF growth line is obtained by shifting the cumulative MTBF line up, parallel to itself, by a distance of <math>\tfrac{1}{1-\alpha }\,\!</math>, as illustrated in the figure below.


[[Image:rga4.1.png|center|500px|Cumulative MTBF vs. Cumulative Test Time postulated by Duane.]]
[[Image:rga4.1.png|center|450px|Cumulative MTBF vs. Cumulative Test Time postulated by Duane.]]


==Parameter Estimation==
==Parameter Estimation==
The Duane model is a two parameter model. Therefore, to use this model as a basis for predicting the reliability growth that could be expected in an equipment development program, procedures must be defined for estimating these parameters as a function of equipment characteristics. Note that, while these parameters can be estimated for a given data set using curve-fitting methods, there exists no underlying theory for the Duane model that could provide a basis for ''a priori'' estimation.
The Duane model is a two parameter model. Therefore, to use this model as a basis for predicting the reliability growth that could be expected in an equipment development program, procedures must be defined for estimating these parameters as a function of equipment characteristics. Note that, while these parameters can be estimated for a given data set using curve-fitting methods, there exists no underlying theory for the Duane model that could provide a basis for ''a priori'' estimation.
One of the parameters of the Duane model is <math>\alpha\,\!</math>. The second parameter can be represented as <math>A\,\!</math> or <math>b\,\!</math> where <math>A=\frac{1}{b}\,\!</math>. There is an option within the Application Setup that allows you to determine whether to display <math>A\,\!</math> or <math>b\,\!</math> for the Duane model. All formulation within this reference uses the parameter <math>b\,\!</math>.
[[Image:DuaneShowAorb.png|center|450px]]


===Graphical Method===
===Graphical Method===
The Duane model for the cumulative failure intensity is:
The Duane model for the cumulative failure intensity is:
   
   
::<math>{{\widehat{{\bar{\lambda }}}}_{c}}=\frac{1}{b}{{T}^{-\alpha }}</math>.
:<math>{{\hat{{\bar{\lambda }}}}_{c}}=\frac{1}{b}{{T}^{-\alpha }}\,\!</math>  


This equation may be linearized by taking the natural log of both sides:
This equation may be linearized by taking the natural log of both sides:


::<math>\ln \left( {{\widehat{{\bar{\lambda }}}}_{c}} \right)=\ln \left( \frac{1}{b} \right)-\alpha \ln (T)</math>
:<math>\ln \left( {{\hat{{\bar{\lambda }}}}_{c}} \right)=\ln \left( \frac{1}{b} \right)-\alpha \ln (T)\,\!</math>


Consequently, plotting <math>\widehat{{\bar{\lambda }}}\,\!</math> versus <math>T\,\!</math> on log-log paper will result in a straight line with a negative slope, such that:
Consequently, plotting <math>\hat{{\bar{\lambda }}}\,\!</math> versus <math>T\,\!</math> on log-log paper will result in a straight line with a negative slope, such that:


*<math>\ln \left ({\frac{1}{b}} \right)\,\!</math> is the y-intercept at <math>T = 1\,\!</math>
*<math>\ln \left ({\frac{1}{b}} \right)\,\!</math> is the y-intercept at <math>T = 1\,\!</math>
*<math>\frac{1}{b}\,\!</math> is the cumulative failure intensity at <math>T = 1\,\!</math>
*<math>\frac{1}{b}\,\!</math> is the cumulative failure intensity at <math>T = 1\,\!</math>
*<math>\alpha\,\!</math> is the slope of the straight line on the log-log plot
*<math>\alpha\,\!</math> is the slope of the straight line on the log-log plot


Similarly, the corresponding MTBF of the cumulative failure intensity can also be linearized by taking the natural log of both sides:  
Similarly, the corresponding MTBF of the cumulative failure intensity can also be linearized by taking the natural log of both sides:  


::<math>\begin{align}
:<math>\begin{align}
  \hat{m_{c}}&=bT^{\alpha }  \\
  \hat{m_{c}}&=bT^{\alpha }  \\
  \ln \hat{m_{c}}&=\ln b+\alpha \ln T  \\
  \ln \hat{m_{c}}&=\ln b+\alpha \ln T  \\
\end{align}</math>
\end{align}\,\!</math>
 


Plotting <math>\hat{m}</math> versus <math>T\,\!</math> on log-log paper will result in a straight line with a positive slope such that:
Plotting <math>\hat{m}\,\!</math> versus <math>T\,\!</math> on log-log paper will result in a straight line with a positive slope such that:


*<math>\ln{b}\,\!</math> is the y-intercept at <math>T = 1\,\!</math>
*<math>\ln{b}\,\!</math> is the y-intercept at <math>T = 1\,\!</math>
*<math>b\,\!</math> is the cumulative mean time between failure at <math>T = 1\,\!</math>
*<math>b\,\!</math> is the cumulative mean time between failure at <math>T = 1\,\!</math>
*<math>\alpha\,\!</math> is the slope of the straight line on the log-log plot
*<math>\alpha\,\!</math> is the slope of the straight line on the log-log plot


Two ways of determining these curves are as follows:
Two ways of determining these curves are as follows:


:1. Predict the <math>{{\widehat{{\bar{\lambda }}}}_{0}}</math> and <math>\hat{m}=\,\!</math>   <math>\tfrac{1}{{{\widehat{{\bar{\lambda }}}}_{0}}}\,\!</math> of the system from its reliability block diagram and available component failure intensities. Plot this value on log-log plotting paper at <math>T=1.\,\!</math> From past experience and from past data for similar equipment, find values of <math>{{\alpha }_{1}}\,\!</math> , the slope of the improvement lines for <math>\widehat{{\bar{\lambda }}}\,\!</math> or <math>\hat{m}\,\!</math> . Modify this <math>\alpha \,\!</math> as necessary. If a better design effort is expected and a more intensive research, test and development or TAAF program is to be implemented, then a 15% improvement in the growth rate may be attainable. Consequently, the available value for slope <math>\alpha \,\!</math> , and <math>{{\alpha }_{1}}\,\!</math> , should be adjusted by this amount. The value to be used will then be <math>\alpha =1.15{{\alpha }_{1}}.\,\!</math> A line is then drawn through point <math>{{\widehat{{\bar{\lambda }}}}_{0}}\,\!</math> and <math>T=1\,\!</math> with the just determined slope <math>\alpha \,\!</math> , keeping in mind that <math>\alpha \,\!</math> is negative for the <math>\widehat{{\bar{\lambda }}}\,\!</math> curve. This line should be extended to the design, development and test time scheduled to be expended to see if the failure intensity goal will indeed be achieved on schedule. It is also possible to find that the design, development and test time to achieve the goal may be earlier than the delivery date or later. If earlier, then either the reliability program effort can be judiciously and appropriately trimmed; or if it is an incentive contract, full advantage is taken of the fact that the failure intensity goal can be exceeded with the associated increased profits to the company. A similar approach may be used for the MTBF growth model, where <math>{{\hat{m}}_{0}}=\tfrac{1}{{{\widehat{{\bar{\lambda }}}}_{0}}}\,\!</math> is plotted at <math>T=1\,\!</math> , and a line is drawn through the point <math>{{\hat{m}}_{0}}\,\!</math> and <math>T=1\,\!</math> with slope <math>\alpha \,\!</math> to obtain the MTBF growth line. If <math>\alpha \,\!</math> values are not available, consult the table below, which gives actual <math>\alpha \,\!</math> values for various types of equipment. These have been obtained from literature or by MTBF growth tests. It may be seen from the following table that <math>\alpha \,\!</math> values range between 0.24 and 0.65. The lower values reflect slow early growth and the higher values reflect fast early growth.
1. Predict the <math>{{\hat{{\bar{\lambda }}}}_{0}}\,\!</math> and <math>\hat{m}=\,\!</math> <math>\tfrac{1}{{{\hat{{\bar{\lambda }}}}_{0}}}\,\!</math> of the system from its reliability block diagram and available component failure intensities. Plot this value on log-log plotting paper at <math>T=1.\,\!</math> From past experience and from past data for similar equipment, find values of <math>{{\alpha }_{1}}\,\!</math>, the slope of the improvement lines for <math>\hat{{\bar{\lambda }}}\,\!</math> or <math>\hat{m}\,\!</math>. Modify this <math>\alpha \,\!</math> as necessary. If a better design effort is expected and a more intensive research, test and development or TAAF program is to be implemented, then a 15% improvement in the growth rate may be attainable. Consequently, the available value for slope <math>\alpha \,\!</math>, and <math>{{\alpha }_{1}}\,\!</math>, should be adjusted by this amount. The value to be used will then be <math>\alpha =1.15{{\alpha }_{1}}.\,\!</math> A line is then drawn through point <math>{{\hat{{\bar{\lambda }}}}_{0}}\,\!</math> and <math>T=1\,\!</math> with the just determined slope <math>\alpha \,\!</math>, keeping in mind that <math>\alpha \,\!</math> is negative for the <math>\hat{{\bar{\lambda }}}\,\!</math> curve. This line should be extended to the design, development and test time scheduled to be expended to see if the failure intensity goal will indeed be achieved on schedule. It is also possible to find that the design, development and test time to achieve the goal may be earlier than the delivery date or later. If earlier, then either the reliability program effort can be judiciously and appropriately trimmed; or if it is an incentive contract, full advantage is taken of the fact that the failure intensity goal can be exceeded with the associated increased profits to the company. A similar approach may be used for the MTBF growth model, where <math>{{\hat{m}}_{0}}=\tfrac{1}{{{\hat{{\bar{\lambda }}}}_{0}}}\,\!</math> is plotted at <math>T=1\,\!</math>, and a line is drawn through the point <math>{{\hat{m}}_{0}}\,\!</math> and <math>T=1\,\!</math> with slope <math>\alpha \,\!</math> to obtain the MTBF growth line. If <math>\alpha \,\!</math> values are not available, consult the table below, which gives actual <math>\alpha \,\!</math> values for various types of equipment. These have been obtained from literature or by MTBF growth tests. It may be seen from the following table that <math>\alpha \,\!</math> values range between 0.24 and 0.65. The lower values reflect slow early growth and the higher values reflect fast early growth.


{|border="1" align="center" style="border-collapse: collapse;" cellpadding="5" cellspacing="5"
{|border="1" align="center" style="border-collapse: collapse;" cellpadding="5" cellspacing="5"
|+'''Sample values for the slope ( <math>\alpha )\,\!</math>  for various equipment'''
|+'''Sample Slope Values for Various Equipment'''
|-
|-
!Equipment
!Equipment
Line 163: Line 162:
|}
|}


:2. During the design, development and test phase and at specific milestones, the <math>\widehat{{\bar{\lambda }}}=\tfrac{1}{{\hat{m}}}\,\!</math> is calculated from the total failures and <math>T\,\!</math> values. These values of <math>\widehat{{\bar{\lambda }}}\,\!</math> or <math>\hat{m}\,\!</math> are plotted above the corresponding <math>T\,\!</math> values on log-log paper. A straight line is drawn favoring these points to minimize the distance between the points and the line, thus establishing the improvement or growth model and its parameters graphically. If needed, linear regression analysis techniques can be used to determine these parameters.
2. During the design, development and test phase and at specific milestones, the <math>\hat{{\bar{\lambda }}}=\tfrac{1}{{\hat{m}}}\,\!</math> is calculated from the total failures and <math>T\,\!</math> values. These values of <math>\hat{{\bar{\lambda }}}\,\!</math> or <math>\hat{m}\,\!</math> are plotted above the corresponding <math>T\,\!</math> values on log-log paper. A straight line is drawn favoring these points to minimize the distance between the points and the line, thus establishing the improvement or growth model and its parameters graphically. If needed, linear regression analysis techniques can be used to determine these parameters.
 
====Graphical Method Example====<!-- THIS SECTION HEADER IS LINKED FROM ANOTHER SECTION IN THIS PAGE. IF YOU RENAME THE SECTION, YOU MUST UPDATE THE LINK(S). -->
A complex system's reliability growth is being monitored and the data set is given in the table below.
 
{|border="1" align="center" style="border-collapse: collapse;" cellpadding="5" cellspacing="5"
|+'''Cumulative Test Hours and the Corresponding Observed Failures for the Complex System'''
|-
!Point Number
!Cumulative Test Time(hours)
!Cumulative Failures
!Cumulative MTBF(hours)
!Instantaneous MTBF(hours)
|-
|1||200 ||2||100.0||100
|-
|2||400 ||3||133.0||200
|-
|3||600 ||4||150.0||200
|-
|4||3,000||11||273.0||342.8
|}
 
Do the following:
:1) Plot the cumulative MTBF growth curve.
:2) Write the equation of this growth curve.
:3) Write the equation of the instantaneous MTBF growth model.
:4) Plot the instantaneous MTBF growth curve.
 
'''Solution'''
 
:1) Given the data in the second and third columns of the above table, the cumulative MTBF,  <math>{{\hat{m}}_{c}}\,\!</math> , values are calculated in the fourth column. The information in the second and fourth columns are then plotted. The first figure below shows the cumulative MTBF while the second figure below shows the instantaneous MTBF. It can be seen that a straight line represents the MTBF growth very well on log-log scales.
 
 
[[Image:rga4.2.png|center|400px|Cumulative MTBF plot]]
<center>Cumulative MTBF plot</center>
 
 
[[Image:rga4.3.png|center|400px|Instantaneous MTBF plot]]
<center>Instantaneous MTBF plot</center>
 
By changing the x-axis scaling, you are able to extend the line to  <math>T=1\,\!</math> . You can get the value of  <math>b\,\!</math>  from the graph by positioning the cursor at the point where the line meets the y-axis. Then read the value of the y-coordinate position at the bottom left corner. In this case,  <math>b\,\!</math>  is approximately 14 hours. The next figure illustrates this.
 
[[Image:rga4.4.png|center|400px|Cumulative MTBF plot for <math>b\approx 14\,\!</math> at <math>T=1\,\!</math>.]]
<center>Cumulative MTBF plot for <math>b \approx 14</math> at <math>T=1\,\!</math></center>
 
 
Another way of determining  <math>b\,\!</math>  is to calculate  <math>\alpha \,\!</math>  by using two points on the fitted straight line and substituting the corresponding  <math>{{\hat{m}}_{c}}\,\!</math>  and  <math>T\,\!</math>  values into:
 
::<math>\alpha =\frac{\ln \left( {{{\hat{m}}}_{{{c}_{2}}}} \right)-\ln \left( {{{\hat{m}}}_{{{c}_{1}}}} \right)}{\ln \left( {{T}_{_{2}}} \right)-\ln \left( {{T}_{_{1}}} \right)}</math>
 
Then substitute this  <math>\alpha \,\!</math>  and choose a set of values for  <math>{{\hat{m}}_{{{c}_{1}}}}\,\!</math>  and  <math>{{T}_{_{1}}}\,\!</math>  into the cumulative MTBF equation, <math>{{\hat{m}}_{c}}=b{{T}^{\alpha }}</math>, and solve for  <math>b\,\!</math> . The slope of the line,  <math>\alpha \,\!</math> , may also be found from the linearized form of the cumulative MTBF equation, or :
 
::<math>\alpha =\frac{\ln \left( {{{\hat{m}}}_{c}} \right)-\ln (b)}{\ln (T)-\ln (1)}</math>
 
Using the cumulative MTBF plot for the example, at <math>{{T}_{_{1}}}=200\,\!</math>  hours,  <math>{{\hat{m}}_{{{c}_{1}}}}=100\,\!</math>  hours, and <math>{{T}_{_{2}}}=3,500\,\!</math>  hours,  <math>{{\hat{m}}_{{{c}_{2}}}}=300\,\!</math>  hours. From the cumulative MTBF plot for  <math>b=14\,\!</math> hours when  <math>T=1\,\!</math>, substituting the first set of values,  <math>b=14\,\!</math>  hours and  <math>\ln 1=0\,\!</math> , into the equation yields:
 
::<math>\begin{align}
  {{\alpha }_{1}}= & \frac{\ln (100)-\ln (14)}{\ln (200)-\ln (1)} \\
  = & 0.3711 
\end{align}</math>
 
 
:2. Substituting the second set of values,  <math>b=14\,\!</math>  hours and  <math>\ln 1=0,\,\!</math>  into the equation yields:
 
::<math>\begin{align}
  {{\alpha }_{2}}= & \frac{\ln (300)-\ln (14)}{\ln (3,500)-\ln (1)} \\
  = & 0.3755 
\end{align}</math>
 
 
Averaging these two  <math>\alpha \,\!</math>  values yields a better estimate of  <math>\widehat{\alpha }=0.3733\,\!</math>.
 
:3. Now the equation for the cumulative MTBF growth curve is:
::<math>{{\hat{m}}_{c}}=14\cdot {{T}^{\text{ }0.3733}}</math>
:4. Using the following equation for the instantaneous MTBF, or
 
::<math>{{m}_{i}} = \frac{1}{1-\alpha }{{{\hat{m}}}_{c}},:\ \ \alpha \not{=}1  </math>
 
::the equation for the instantaneous MTBF growth curve is:
 
::<math>\begin{align}
{{\hat{m}}_{i}}=\frac{1}{1-0.3733} \cdot {{14T}^{0.3733}}
\end{align}</math>


The above equation is plotted in the instantaneous MTBF plot shown in the example and in the cumulative and instantaneous MTBF vs. Time plot. In the following figure, you can see that a parallel shift upward of the cumulative MTBF,  <math>{{\hat{m}}_{c}}\,\!</math> , line by a distance of  <math>\tfrac{1}{1-\alpha }\,\!</math>  gives the instantaneous MTBF, or the  <math>{{\hat{m}}_{i}}\,\!</math> , line.
====Graphical Method Example====
 
{{:Duane Graphical Method Example}}
[[Image:rga4.5.png|center|400px|Cumulative and Instantaneous MTBF vs. Time plot.]]
<center>Cumulative and Instantaneous MTBF vs. Time plot</center>


===Least Squares (Linear Regression)===
===Least Squares (Linear Regression)===
The parameters can also be estimated using a mathematical approach. To do this, linearize the MTBF of the cumulative failure intensity  by taking the natural log of both sides, and then apply least squares analysis. For example:  
The parameters can also be estimated using a mathematical approach. To do this, linearize the MTBF of the cumulative failure intensity  by taking the natural log of both sides, and then apply least squares analysis. For example:  


::<math>\begin{align}
:<math>\begin{align}
  \hat{m_{c}}&=bT^{\alpha }  \\
  \hat{m_{c}}&=bT^{\alpha }  \\
  \ln \hat{m_{c}}&=\ln b+\alpha \ln T  \\
  \ln \hat{m_{c}}&=\ln b+\alpha \ln T  \\
\end{align}</math>
\end{align}\,\!</math>


For simplicity in the calculations, let:  
For simplicity in the calculations, let:  


::<math>\begin{align}
:<math>\begin{align}
   \ln ({{m}_{ci}})= & {{Y}_{i}} \\  
   \ln ({{m}_{ci}})= & {{Y}_{i}} \\  
  \ln (b)= & a \\  
  \ln (b)= & a \\  
  \alpha = & c \\  
  \alpha = & c \\  
  \ln ({{T}_{i}})= & {{X}_{i}}   
  \ln ({{T}_{i}})= & {{X}_{i}}   
\end{align}</math>
\end{align}\,\!</math>


Therefore, the equation becomes:  
Therefore, the equation becomes:  


::<math>{{Y}_{i}}=\widehat{a}+\widehat{c}{{X}_{i}}</math>
:<math>{{Y}_{i}}=\hat{a}+\hat{c}{{X}_{i}}\,\!</math>


Assume that a set of data pairs <math>({{X}_{1}},{{Y}_{1}})\,\!</math> , <math>({{X}_{2}},{{Y}_{2}})\,\!</math> ,..., <math>({{X}_{N}},{{Y}_{N}})\,\!</math> were obtained and plotted. Then according to the Least Squares Principle, which minimizes the vertical distance between the data points and the straight line fitted to the data, the best fitting straight line to this data set is the straight line <math>Y=\widehat{a}+\widehat{c}X\,\!</math> such that:  
Assume that a set of data pairs <math>({{X}_{1}},{{Y}_{1}})\,\!</math>, <math>({{X}_{2}},{{Y}_{2}})\,\!</math>,..., <math>({{X}_{N}},{{Y}_{N}})\,\!</math> were obtained and plotted. Then according to the Least Squares Principle, which minimizes the vertical distance between the data points and the straight line fitted to the data, the best fitting straight line to this data set is the straight line <math>Y=\hat{a}+\hat{c}X\,\!</math> such that:  


::<math>\underset{i=1}{\overset{N}{\mathop \sum }}\,{{(\widehat{a}+\widehat{c}{{X}_{i}}-{{Y}_{i}})}^{2}}=\underset{(a,c)}{\mathop{min}}\,\underset{i=1}{\overset{N}{\mathop \sum }}\,{{(a+c{{X}_{i}}-{{Y}_{i}})}^{2}}</math>
:<math>\underset{i=1}{\overset{N}{\mathop \sum }}\,{{(\hat{a}+\hat{c}{{X}_{i}}-{{Y}_{i}})}^{2}}=\underset{(a,c)}{\mathop{min}}\,\underset{i=1}{\overset{N}{\mathop \sum }}\,{{(a+c{{X}_{i}}-{{Y}_{i}})}^{2}}\,\!</math>


where <math>\widehat{a}\,\!</math> and <math>\widehat{c}\,\!</math> are the least squares estimates of <math>a\,\!</math> and <math>c\,\!</math> . To obtain <math>\widehat{a}\,\!</math> and <math>\widehat{c}\,\!</math> , let:  
where <math>\hat{a}\,\!</math> and <math>\hat{c}\,\!</math> are the least squares estimates of <math>a\,\!</math> and <math>c\,\!</math>. To obtain <math>\hat{a}\,\!</math> and <math>\hat{c}\,\!</math>, let:  


::<math>F=\underset{i=1}{\overset{N}{\mathop \sum }}\,{{(a+c{{X}_{i}}-{{Y}_{i}})}^{2}}</math>
:<math>F=\underset{i=1}{\overset{N}{\mathop \sum }}\,{{(a+c{{X}_{i}}-{{Y}_{i}})}^{2}}\,\!</math>


Differentiating <math>F\,\!</math> with respect to <math>a\,\!</math> and <math>c\,\!</math> yields:  
Differentiating <math>F\,\!</math> with respect to <math>a\,\!</math> and <math>c\,\!</math> yields:  


::<math>\frac{\partial F}{\partial a}=2\underset{i=1}{\overset{N}{\mathop \sum }}\,(a+c{{X}_{i}}-{{Y}_{i}})</math>
:<math>\frac{\partial F}{\partial a}=2\underset{i=1}{\overset{N}{\mathop \sum }}\,(a+c{{X}_{i}}-{{Y}_{i}})\,\!</math>


:and:  
and:  


::<math>\frac{\partial F}{\partial c}=2\underset{i=1}{\overset{N}{\mathop \sum }}\,(a+c{{X}_{i}}-{{Y}_{i}}){{X}_{i}}</math>
:<math>\frac{\partial F}{\partial c}=2\underset{i=1}{\overset{N}{\mathop \sum }}\,(a+c{{X}_{i}}-{{Y}_{i}}){{X}_{i}}\,\!</math>


Set those two equations equal to zero:  
Set those two equations equal to zero:  


::<math>\underset{i=1}{\overset{N}{\mathop \sum }}\,(a+c{{X}_{i}}-{{Y}_{i}})=\underset{i=1}{\overset{N}{\mathop \sum }}\,(\widehat{{{Y}_{i}}}-{{Y}_{i}})=-\underset{i=1}{\overset{N}{\mathop \sum }}\,({{Y}_{i}}-\widehat{{{Y}_{i}}})=0</math>
:<math>\underset{i=1}{\overset{N}{\mathop \sum }}\,(a+c{{X}_{i}}-{{Y}_{i}})=\underset{i=1}{\overset{N}{\mathop \sum }}\,(\hat{{{Y}_{i}}}-{{Y}_{i}})=-\underset{i=1}{\overset{N}{\mathop \sum }}\,({{Y}_{i}}-\hat{{{Y}_{i}}})=0\,\!</math>


:and:  
and:  


::<math>\underset{i=1}{\overset{N}{\mathop \sum }}\,(a+c{{X}_{i}}-{{Y}_{i}}){{X}_{i}}=\underset{i=1}{\overset{N}{\mathop \sum }}\,(\widehat{{{Y}_{i}}}-{{Y}_{i}}){{X}_{i}}=-\underset{i=1}{\overset{N}{\mathop \sum }}\,({{Y}_{i}}-\widehat{{{Y}_{i}}}){{X}_{i}}=0</math>
:<math>\underset{i=1}{\overset{N}{\mathop \sum }}\,(a+c{{X}_{i}}-{{Y}_{i}}){{X}_{i}}=\underset{i=1}{\overset{N}{\mathop \sum }}\,(\hat{{{Y}_{i}}}-{{Y}_{i}}){{X}_{i}}=-\underset{i=1}{\overset{N}{\mathop \sum }}\,({{Y}_{i}}-\hat{{{Y}_{i}}}){{X}_{i}}=0\,\!</math>


Solve the equations simultaneously:  
Solve the equations simultaneously:  


::<math> \begin{align}
:<math>\begin{align}
\widehat{a}& =\frac{\underset{i=1}{\overset{N}{\mathop{\sum }}}\,{{Y}_{i}}}N-\widehat{c} \frac{\underset{i=1}{\overset{N}{\mathop{\sum }}}\,{{X}_{i}}}N \\
\hat{a}= & \frac{\sum\limits_{i=1}^{N}{{{Y}_{i}}}}{N}-\hat{c}\frac{\sum\limits_{i=1}^{N}{{{X}_{i}}}}{N}\\
& = \overline{Y} - \hat{c}\overline{X} \\
= & \bar{Y}-\hat{c}\bar{X}\end{align}
\end{align}</math>
\,\!</math>


and:  
and:  


::<math>\widehat{c}=\frac{\underset{i=1}{\overset{N}{\mathop{\sum }}}\,{{X}_{i}}{{Y}_{i}}-\tfrac{\left( \underset{i=1}{\overset{N}{\mathop{\sum }}}\,{{X}_{i}}\underset{i=1}{\overset{N}{\mathop{\sum }}}\,{{Y}_{i}} \right)}{N}}{\underset{i=1}{\overset{N}{\mathop{\sum }}}\,X_{i}^{2}-\tfrac{{{\left( \underset{i=1}{\overset{N}{\mathop{\sum }}}\,{{X}_{i}} \right)}^{2}}}{N}}</math>
:<math>\hat{c}=\frac{\underset{i=1}{\overset{N}{\mathop{\sum }}}\,{{X}_{i}}{{Y}_{i}}-\tfrac{\left( \underset{i=1}{\overset{N}{\mathop{\sum }}}\,{{X}_{i}}\underset{i=1}{\overset{N}{\mathop{\sum }}}\,{{Y}_{i}} \right)}{N}}{\underset{i=1}{\overset{N}{\mathop{\sum }}}\,X_{i}^{2}-\tfrac{{{\left( \underset{i=1}{\overset{N}{\mathop{\sum }}}\,{{X}_{i}} \right)}^{2}}}{N}}\,\!</math>


Now substituting back <math>\ln ({{m}_{ci}})={{Y}_{i}},\,\!</math> <math>\ln (b)=a,\,\!</math> <math>\alpha =c\,\!</math> and <math>\ln ({{T}_{i}})={{X}_{i}},\,\!</math> we have:


Now substituting back  <math>\ln ({{m}_{ci}})={{Y}_{i}},\,\!</math>  <math>\ln (b)=a,\,\!</math>  <math>\alpha =c\,\!</math>  and  <math>\ln ({{T}_{i}})={{X}_{i}},\,\!</math>  we have:
:<math>\hat{b}={{e}^{\tfrac{1}{n}\left[ \underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{m}_{ci}})-\alpha \underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{T}_{i}}) \right]}}\,\!</math>
 
 
::<math>\widehat{b}={{e}^{\tfrac{1}{n}\left[ \underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{m}_{ci}})-\alpha \underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{T}_{i}}) \right]}}</math>
 
 
:where:
 
::<math>\widehat{\alpha }=\frac{\underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{T}_{i}})\ln ({{m}_{ci}})-\tfrac{\underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{T}_{i}})\underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{m}_{ci}})}{n}}{\underset{i=1}{\overset{n}{\mathop{\sum }}}\,{{\left[ \ln ({{T}_{i}}) \right]}^{2}}-\tfrac{{{\left( \underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{T}_{i}}) \right)}^{2}}}{n}}</math>
 
 
====Least Squares Example 1====
Using the data from the [[Duane_Model#Graphical_Method_Example|Graphical Method Example]] given above, estimate the parameters of the MTBF model using least squares.
 
'''Solution'''
 
From the data table:
 
::<math>\begin{align}
\underset{i=1}{\overset{n}{\mathop \sum }}\,\ln ({{T}_{i}})&= & 25.693 \\
\underset{i=1}{\overset{n}{\mathop \sum }}\,\ln ({{T}_{i}})\ln ({{m}_{ci}})&= & 130.66 \\
\underset{i=1}{\overset{n}{\mathop \sum }}\,\ln ({{m}_{ci}})&= & 20.116 \\
\underset{i=1}{\overset{n}{\mathop \sum }}\,{{\left[ \ln ({{T}_{i}}) \right]}^{2}}&= & 168.99 
\end{align}</math>
 
 
Obtain the value of <math>\hat{\alpha}</math> from the least squares analysis, or:
::<math>\begin{align}
\widehat{\alpha }&=\frac{\underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{T}_{i}})\ln ({{m}_{ci}})-\tfrac{\underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{T}_{i}})\underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{m}_{ci}})}{n}}{\underset{i=1}{\overset{n}{\mathop{\sum }}}\,{{\left[ \ln ({{T}_{i}}) \right]}^{2}}-\tfrac{{{\left( \underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{T}_{i}}) \right)}^{2}}}{n}} \\
& =  \frac{130.66-\tfrac{25.693\cdot 20.116}{4}}{168.99-\tfrac{{{25.693}^{2}}}{4}} \\
& =  0.3671 
\end{align}</math>
 
 
Obtain the value <math>\hat{b}</math> from the least squares analysis, or:
 
::<math>\begin{align}
\widehat{b}&={{e}^{\tfrac{1}{n}\left[ \underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{m}_{ci}})-\alpha \underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{T}_{i}}) \right]}} \\
& = {{e}^{\tfrac{1}{4}(20.116-0.3671\cdot 25.693)}} \\
& =  14.456 
\end{align}</math>


where:


Therefore, the cumulative MTBF becomes:
:<math>\hat{\alpha }=\frac{\underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{T}_{i}})\ln ({{m}_{ci}})-\tfrac{\underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{T}_{i}})\underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{m}_{ci}})}{n}}{\underset{i=1}{\overset{n}{\mathop{\sum }}}\,{{\left[ \ln ({{T}_{i}}) \right]}^{2}}-\tfrac{{{\left( \underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{T}_{i}}) \right)}^{2}}}{n}}\,\!</math>


::<math>\begin{align}
{{:Duane Linear Regression Examples}}
\hat{m_{c}}&=bT^{\alpha } \\
&=14.456\cdot {{T}^{0.3671}} \\
\end{align}</math>
 
 
The equation for the instantaneous MTBF growth curve is:
 
::<math>\begin{align}
{{\hat{m}}_{i}}&=\frac{1}{1-\alpha }{{{\hat{m}}}_{c}},:\ \ \alpha \not{=}1  \\
&=\frac{1}{1-0.3671}(14.456){{T}^{0.3671}} \\
\end{align}</math>
 
====Least Squares Example 2==== <!-- THIS SECTION HEADER IS LINKED FROM ANOTHER SECTION IN THIS PAGE. IF YOU RENAME THE SECTION, YOU MUST UPDATE THE LINK(S). -->
For the data given in columns 1 and 2 of the following table, estimate the Duane parameters using least squares.
{|border="1" align="center" style="border-collapse: collapse;" cellpadding="5" cellspacing="5"
|+'''Failure times data'''
|-
!(1)Failure Number
!(2)Failure Time(hours)
!(3)<math>\ln{T_i}\,\!</math>
!(4)<math>\ln{T_i}^2\,\!</math>
!(5)<math>m_c\,\!</math>
!(6)<math>\ln{m_c}\,\!</math>
!(7)<math>\ln{m_c}\cdot\ln{T_i}\,\!</math>
|-
|1||9.2 ||2.219 ||4.925 ||9.200||2.219||4.925
|-
|2||25||3.219 ||10.361||12.500||2.526||8.130
|-
|3||61.5||4.119 ||16.966||20.500||3.020||12.441
|-
|4||260 ||5.561 ||30.921||65.000||4.174||23.212
|-
|5||300 ||5.704 ||32.533||60.000||4.094||23.353
|-
|6||710||6.565 ||43.103||118.333||4.774||31.339
|-
|7||916||6.820 ||46.513||130.857||4.874||33.241
|-
|8||1010||6.918 ||47.855||126.250||4.838||33.470
|-
|9||1220||7.107 ||50.504||135.556||4.909||34.889
|-
|10||2530||7.836||61.402||253.000||5.533||43.359
|-
|11||3350||8.117||65.881||304.545||5.719||46.418
|-
|12||4200||8.343||69.603||350.000||5.858||48.872
|-
|13||4410||8.392||70.419||339.231||5.827||48.895
|-
|14||4990||8.515||72.508||356.429||5.876||50.036
|-
|15||5570||8.625||74.393||371.333||5.917||51.036
|-
|16||8310||9.025||81.455||519.375||6.253||56.431
|-
|17||8530||9.051||81.927||501.765||6.218||56.282
|-
|18||9200||9.127||83.301||511.111||6.237||56.921
|-
|19||10500||9.259||85.731||552.632||6.315||58.469
|-
|20||12100||9.401||88.378||605.000||6.405||60.215
|-
|21||13400||9.503||90.307||638.095||6.458||61.375
|-
|22||14600||9.589||91.945||663.636||6.498||62.305
|-
|23||22000||9.999||99.976||956.522||6.863||68.625
|-
| ||Sum =||173.013||1400.908||7600.870||121.406||974.242
|}
 
'''Solution'''
 
To estimate the parameters using least squares, the values in columns 3, 4, 5, 6 and 7 are calculated. The cumulative MTBF,  <math>{{m}_{c}}\,\!</math> , is calculated by dividing the failure time by the failure number. The value of <math>\widehat{\alpha }\,\!</math>  is:
 
::<math>\begin{align}
\widehat{\alpha }&=\frac{\underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{T}_{i}})\ln ({{m}_{ci}})-\tfrac{\underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{T}_{i}})\underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{m}_{ci}})}{n}}{\underset{i=1}{\overset{n}{\mathop{\sum }}}\,{{\left[ \ln ({{T}_{i}}) \right]}^{2}}-\tfrac{{{\left( \underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{T}_{i}}) \right)}^{2}}}{n}} \\
& = \frac{974.242-\tfrac{173.013\cdot 121.406}{23}}{1400.908-\tfrac{{{(173.013)}^{2}}}{23}} \\
& = 0.6133 
\end{align}</math>
 
 
The estimator of  <math>b\,\!</math> is estimated to be:
 
::<math>\begin{align}
\widehat{b}&={{e}^{\tfrac{1}{n}\left[ \underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{m}_{ci}})-\alpha \underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{T}_{i}}) \right]}} \\
& = {{e}^{\tfrac{1}{23}(121.406-0.6133\cdot 173.013)}} \\
& = 1.9453 
\end{align}</math>
 
 
Therefore, the cumulative MTBF becomes:
 
::<math>\begin{align}
\hat{m_{c}}&= bT^{\alpha } \\
& =1.9453\cdot {{T}^{0.613}} \\
\end{align}</math>
 
 
Using the equation for the instantaneous MTBF growth curve,
 
::<math>\begin{align}
{{\hat{m}}_{i}}&=\frac{1}{1-\alpha }{{{\hat{m}}}_{c}},:\ \ \alpha \not{=}1  \\
& =\frac{1}{1-0.613}(1.945){{T}^{0.613}} \\
\end{align}</math>
 
[[Image:rga4.6.png|center|400px|Duane plot for Example 3.]]
 
====Least Squares Example 3====
For the data given in the following table, estimate the Duane parameters using least squares.
 
{|border="1" align="center" style="border-collapse: collapse;" cellpadding="5" cellspacing="5"
|+'''Multiple systems (known operating times) data}'''
!Run Number
!Failed Unit
!Test Time 1
!Test Time 2
!Cumulative Time
|-
|1||1|| 0.2||2.0||2.2
|-
|2||2||1.7||2.9||4.6
|-
|3||2||4.5||5.2||9.7
|-
|4||2||5.8||9.1||14.9
|-
|5||2||17.3||9.2||26.5
|-
|6||2||29.3||24.1||53.4
|-
|7||1||36.5||61.1||97.6
|-
|8||2||46.3||69.6||115.9
|-
|9||1||63.6||78.1||141.7
|-
|10||2||64.4||85.4||149.8
|-
|11||1||74.3||93.6||167.9
|-
|12||1||106.6||103||209.6
|-
|13||2||195.2||117||312.2
|-
|14||2||235.1||134.3||369.4
|-
|15||1||248.7||150.2||398.9
|-
|16||2||256.8||164.6||421.4
|-
|17||2||261.1||174.3||435.4
|-
|18||2||299.4||193.2||492.6
|-
|19||1||305.3||234.2||539.5
|-
|20||1||326.9||257.3||584.2
|-
|21||1||339.2||290.2||629.4
|-
|22||1||366.1||293.1||659.2
|-
|23||2||466.4||316.4||782.8
|-
|24||1||504||373.2||877.2
|-
|25||1||510||375.1||885.1
|-
|26||2||543.2||386.1||929.3
|-
|27||2||635.4||453.3||1088.7
|-
|28||1||641.2||485.8||1127
|-
|29||2||755.8||573.6||1329.4
|}
'''Solution'''
 
The solution to this example follows the same procedure as the previous example. Therefore, from the table shown above:
 
::<math>\begin{align}
  \underset{i=1}{\overset{29}{\mathop \sum }}\,\ln ({{T}_{i}})= & 154.151 \\
  \underset{i=1}{\overset{29}{\mathop \sum }}\,\ln {{({{T}_{i}})}^{2}}= & 902.592 \\
  \underset{i=1}{\overset{29}{\mathop \sum }}\,\ln ({{m}_{c}})= & 82.884 \\
  \underset{i=1}{\overset{29}{\mathop \sum }}\,\ln ({{T}_{i}})\cdot \ln ({{m}_{c}})= & 483.154 
\end{align}</math>
 
 
For least squares, the value of <math>\alpha \,\!</math> is:
 
::<math>\begin{align}
\widehat{\alpha }&=\frac{\underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{T}_{i}})\ln ({{m}_{ci}})-\tfrac{\underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{T}_{i}})\underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{m}_{ci}})}{n}}{\underset{i=1}{\overset{n}{\mathop{\sum }}}\,{{\left[ \ln ({{T}_{i}}) \right]}^{2}}-\tfrac{{{\left( \underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{T}_{i}}) \right)}^{2}}}{n}} \\
& = \frac{483.154-\tfrac{154.151\cdot 82.884}{29}}{902.592-\tfrac{{{(154.151)}^{2}}}{29}} \\
& = 0.5115 
\end{align}</math>
 
 
The value of the estimator <math>b\,\!</math> is:
 
::<math>\begin{align}
\widehat{b}&={{e}^{\tfrac{1}{n}\left[ \underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{m}_{ci}})-\alpha \underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{T}_{i}}) \right]}} \\
& = {{e}^{\tfrac{1}{29}(82.884-0.5115\cdot 154.151)}} \\
& = 1.1495 
\end{align}</math>
 
 
Therefore, the cumulative MTBF is:
 
::<math>\begin{align}
\hat{m_{c}}&=bT^{\alpha }
& = 1.1495\cdot {{T}^{0.5115}}
\end{align}</math>
 
 
Using the equation for the instantaneous MTBF growth,
 
::<math>\begin{align}
{{\hat{m}}_{i}}&=\frac{1}{1-\alpha }{{{\hat{m}}}_{c}},:\ \ \alpha \not{=}1  \\
& =\frac{1}{1-0.5115}(1.1495){{T}^{0.5115}}
\end{align}</math>


===Maximum Likelihood Estimators===
===Maximum Likelihood Estimators===
 
L. H. Crow [[RGA_References|[17]]] noted that the Duane model could be stochastically represented as a Weibull process, allowing for statistical procedures to be used in the application of this model in reliability growth. This statistical extension became what is known as the ''Crow-AMSAA (NHPP)'' model. The Crow-AMSAA model, which is described in the [[Crow-AMSAA (NHPP)|Crow-AMSAA (NHPP) chapter]], provides a complete Maximum Likelihood Estimation (MLE) solution to the Duane model.
L. H. Crow [[RGA_References|[17]]] noted that the Duane model could be stochastically represented as a Weibull process, allowing for statistical procedures to be used in the application of this model in reliability growth. This statistical extension became what is known as the ''Crow-AMSAA (NHPP)'' model. The Crow-AMSAA model, which is described in the [[Crow-AMSAA - NHPP|Crow-AMSAA - NHPP chapter]], provides a complete Maximum Likelihood Estimation (MLE) solution to the Duane model.


==Confidence Bounds==
==Confidence Bounds==
Least squares confidence bounds can be computed for both the model parameters and metrics of interest for the Duane model.
Least squares confidence bounds can be computed for both the model parameters and metrics of interest for the Duane model.


===Parameter Bounds===
===Parameter Bounds===
Apply least squares analysis on the Duane model:  
Apply least squares analysis on the Duane model:  


::<math>\ln ({{\hat{m}}_{c}})=\ln (b)+\alpha \ln (t)</math>
:<math>\ln ({{\hat{m}}_{c}})=\ln (b)+\alpha \ln (t)\,\!</math>
 


The unbiased estimator of <math>{{\sigma}^{2}}\,\!</math> can be obtained from:  
The unbiased estimator of <math>{{\sigma}^{2}}\,\!</math> can be obtained from:  


::<math>{{\sigma }^{2}}=Var\left[ \ln {{m}_{c}}(t) \right]=\frac{SSE}{(n-2)}</math>
:<math>{{\sigma }^{2}}=Var\left[ \ln {{m}_{c}}(t) \right]=\frac{SSE}{(n-2)}\,\!</math>


where:  
where:  


::<math>SSE=\underset{i=1}{\overset{n}{\mathop \sum }}\,{{\left[ \ln {{{\hat{m}}}_{c}}({{t}_{i}})-\ln {{m}_{c}}({{t}_{i}}) \right]}^{2}}</math>
:<math>SSE=\underset{i=1}{\overset{n}{\mathop \sum }}\,{{\left[ \ln {{{\hat{m}}}_{c}}({{t}_{i}})-\ln {{m}_{c}}({{t}_{i}}) \right]}^{2}}\,\!</math>
 


Thus, the confidence bounds on <math>\alpha \,\!</math> and <math>b\,\!</math> are:
Thus, the confidence bounds on <math>\alpha \,\!</math> and <math>b\,\!</math> are:


::<math>C{{B}_{\alpha }}=\hat{\alpha }\pm {{t}_{n-2,\alpha /2}}SE(\hat{\alpha })</math>
:<math>C{{B}_{\alpha }}=\hat{\alpha }\pm {{t}_{n-2,\alpha /2}}SE(\hat{\alpha })\,\!</math>


:<math>C{{B}_{b}}=\hat{b}{{e}^{\pm {{t}_{n-2,\alpha /2}}SE\left[ \ln (\hat{b}) \right]}}\,\!</math>


::<math>C{{B}_{b}}=\hat{b}{{e}^{\pm {{t}_{n-2,\alpha /2}}SE\left[ \ln (\hat{b}) \right]}}</math>
where <math>{{t}_{n-2,\alpha /2}}\,\!</math> denotes the percentage point of the <math>t\,\!</math> distribution with <math>n-2\,\!</math> degrees of freedom such that <math>P\{{{t}_{n-2}}\ge {{t}_{\alpha /2,n-2}}\}=\alpha /2\,\!</math> and:


:<math>SE(\hat{\alpha })=\frac{\sigma }{\sqrt{{{S}_{xx}}}}\,\!</math>


where  <math>{{t}_{n-2,\alpha /2}}\,\!</math>  denotes the percentage point of the  <math>t\,\!</math>  distribution with  <math>n-2\,\!</math>  degrees of freedom such that  <math>P\{{{t}_{n-2}}\ge {{t}_{\alpha /2,n-2}}\}=\alpha /2\,\!</math> and:
:<math>SE\left[ \ln (\hat{b}) \right]=\sigma \cdot \sqrt{\frac{\underset{i=1}{\overset{n}{\mathop{\sum }}}\,{{(\ln {{t}_{i}})}^{2}}}{n\cdot {{S}_{xx}}}}\,\!</math>


::<math>SE(\hat{\alpha })=\frac{\sigma }{\sqrt{{{S}_{xx}}}}</math>
:<math>{{S}_{xx}}=\left[ \underset{i=1}{\overset{n}{\mathop \sum }}\,{{(\ln {{t}_{i}})}^{2}} \right]-\frac{1}{n}{{\left( \underset{i=1}{\overset{n}{\mathop \sum }}\,\ln ({{t}_{i}}) \right)}^{2}}\,\!</math>
 
 
::<math>SE\left[ \ln (\hat{b}) \right]=\sigma \cdot \sqrt{\frac{\underset{i=1}{\overset{n}{\mathop{\sum }}}\,{{(\ln {{t}_{i}})}^{2}}}{n\cdot {{S}_{xx}}}}</math>
 
 
::<math>{{S}_{xx}}=\left[ \underset{i=1}{\overset{n}{\mathop \sum }}\,{{(\ln {{t}_{i}})}^{2}} \right]-\frac{1}{n}{{\left( \underset{i=1}{\overset{n}{\mathop \sum }}\,\ln ({{t}_{i}}) \right)}^{2}}</math>


===Other Bounds===
===Other Bounds===
Line 632: Line 270:
Confidence bounds also can be obtained on the cumulative MTBF and the cumulative failure intensity:  
Confidence bounds also can be obtained on the cumulative MTBF and the cumulative failure intensity:  


::<math>C{{B}_{{{m}_{c}}}}={{\hat{m}}_{c}}(t){{e}^{\pm {{z}_{\alpha }}\sqrt{Var\left[ \ln ({{{\hat{m}}}_{c}}) \right]}}}</math>
:<math>C{{B}_{{{m}_{c}}}}={{\hat{m}}_{c}}(t){{e}^{\pm {{z}_{\alpha }}\sqrt{Var\left[ \ln ({{{\hat{m}}}_{c}}) \right]}}}\,\!</math>


:<math>Var\left[ \ln ({{{\hat{m}}}_{c}}) \right]=\frac{\sum\limits_{i=1}^{n}{{{\left( \ln {{{\hat{m}}}_{c}}({{t}_{i}})-\ln {{m}_{c}}({{t}_{i}}) \right)}^{2}}}}{n-2}\cdot \left( \frac{1}{n}+\frac{{{\left( \ln (t)-\frac{\sum\limits_{i=1}^{n}{\ln ({{t}_{i}})}}{n} \right)}^{2}}}{\sum\limits_{i=1}^{n}{{{\left( \ln ({{t}_{i}})-\frac{\sum\limits_{i=1}^{n}{\ln ({{t}_{i}})}}{n} \right)}^{2}}}} \right)\,\!</math>


::<math>\begin{align}
:<math>\begin{align}
   {{[{{\lambda }_{c}}(t)]}_{L}}= & \frac{1}{{{[{{m}_{c}}(t)]}_{u}}} \\  
   {{[{{\lambda }_{c}}(t)]}_{L}}= & \frac{1}{{{[{{m}_{c}}(t)]}_{u}}} \\  
   {{[{{\lambda }_{c}}(t)]}_{U}}= & \frac{1}{{{[{{m}_{c}}(t)]}_{l}}}   
   {{[{{\lambda }_{c}}(t)]}_{U}}= & \frac{1}{{{[{{m}_{c}}(t)]}_{l}}}   
\end{align}</math>
\end{align}\,\!</math>


When <math>n\,\!</math> is large, the approximate <math>100(1-\alpha )%\,\!</math> confidence bounds for instantaneous MTBF are given by:  
When <math>n\,\!</math> is large, the approximate <math>100(1-\alpha )%\,\!</math> confidence bounds for instantaneous MTBF are given by:  


::<math>\begin{align}
:<math>\begin{align}
   {{m}_{i}}{{(t)}_{L}}= & \frac{{{[{{m}_{c}}(t)]}_{L}}}{{\hat{\beta }}} \\  
   {{m}_{i}}{{(t)}_{L}}= & \frac{{{[{{m}_{c}}(t)]}_{L}}}{{\hat{\beta }}} \\  
   {{m}_{i}}{{(t)}_{U}}= & \frac{{{[{{m}_{c}}(t)]}_{U}}}{{\hat{\beta }}}   
   {{m}_{i}}{{(t)}_{U}}= & \frac{{{[{{m}_{c}}(t)]}_{U}}}{{\hat{\beta }}}   
\end{align}</math>
\end{align}\,\!</math>
 


and  
and  
::<math>\lambda_{i}(t) = \frac {1}{m_{i}(t)}</math>
:<math>\lambda_{i}(t) = \frac {1}{m_{i}(t)}\,\!</math>
 


therefore, the confidence bounds on the instantaneous failure intensity are:  
therefore, the confidence bounds on the instantaneous failure intensity are:  


::<math>\begin{align}
:<math>\begin{align}
   {{[{{\lambda }_{i}}(t)]}_{L}}= & \frac{1}{{{[{{m}_{i}}(t)]}_{U}}} \\  
   {{[{{\lambda }_{i}}(t)]}_{L}}= & \frac{1}{{{[{{m}_{i}}(t)]}_{U}}} \\  
   {{[{{\lambda }_{c}}(t)]}_{U}}= & \frac{1}{{{[{{m}_{i}}(t)]}_{L}}}   
   {{[{{\lambda }_{c}}(t)]}_{U}}= & \frac{1}{{{[{{m}_{i}}(t)]}_{L}}}   
\end{align}</math>
\end{align}\,\!</math>


===Duane Confidence Bounds Example===
===Duane Confidence Bounds Example===
For the data given above in [[Duane_Model#Least_Squares_Example_2|Least Squares Example 2]], calculate the 90% confidence bounds for:
{{:Duane Confidence Bounds Example}}
 
#The parameters <math>\alpha\,\!</math> and <math>b\,\!</math>.
#The cumulative and instantaneous failure intensity.
#The cumulative and instantaneous MTBF.
 
'''Solution'''
 
1.  Using the values of  <math>\widehat{b}\,\!</math>  and  <math>\widehat{\alpha }\,\!</math>  estimated from the least squares analysis in [[Duane_Model#Least_Squares_Example_2|Least Squares Example 2]]:
 
::<math>\widehat{b}=1.9453</math>
::<math>\widehat{\alpha}=0.6133</math>
 
then:
 
::<math>\begin{align}
{{S}_{xx}}&=\left[ \underset{i=1}{\overset{n}{\mathop \sum }}\,{{(\ln {{t}_{i}})}^{2}} \right]-\frac{1}{n}{{\left( \underset{i=1}{\overset{n}{\mathop \sum }}\,\ln ({{t}_{i}}) \right)}^{2}} \\
& = 1400.9084-1301.4545 \\
& = 99.4539 
\end{align}</math>
 
 
::<math>\begin{align}
  SE(\hat{\alpha })= & \frac{\sigma }{\sqrt{{{S}_{xx}}}} \\
  = & \frac{0.08428}{9.9727} \\
  = & 0.008452 
\end{align}</math>
 
 
::<math>\begin{align}
  SE(\ln \hat{b})= & \sigma \cdot \sqrt{\frac{\underset{i=1}{\overset{n}{\mathop{\sum }}}\,{{(\ln {{T}_{i}})}^{2}}}{n\cdot {{S}_{xx}}}} \\
= & 0.065960 
\end{align}</math>
 
 
Thus, the 90% confidence bounds on parameter  <math>\alpha \,\!</math>  are:
 
::<math>C{{B}_{\alpha }}=\hat{\alpha }\pm {{t}_{n-2,\alpha /2}}SE(\hat{\alpha })</math>
 
::<math>\begin{align}
  {{\alpha }_{L}}= & 0.602050 \\
  {{\alpha }_{U}}= & 0.624417 
\end{align}</math>
 
 
And 90% confidence bounds on parameter  <math>b\,\!</math>  are:
 
::<math>C{{B}_{b}}=\hat{b}{{e}^{\pm {{t}_{n-2,\alpha /2}}SE\left[ \ln (\hat{b}) \right]}}</math>
 
::<math>\begin{align}
  {{b}_{L}}= & 1.7831 \\
  {{b}_{U}}= & 2.1231 
\end{align}</math>
 
 
2.  The cumulative failure intensity is:
 
::<math>\begin{align}
  {{\lambda }_{c}}= & \frac{1}{1.9453}\cdot {{22000}^{-0.6133}} \\
= & 0.00111689 
\end{align}</math>
 
 
And the instantaneous failure intensity is equal to:
 
::<math>\begin{align}
  {{\lambda }_{i}}= & \frac{1}{1.9453}\cdot (1-0.6133)\cdot {{22000}^{-0.6133}} \\
= & 0.00043198 
\end{align}</math>
 
 
So, at the 90% confidence level and for  <math>T=22,000\,\!</math>  hours, the confidence bounds on cumulative failure intensity are:
 
::<math>\begin{align}
  {{[{{\lambda }_{c}}(t)]}_{L}}= & 0.00100254 \\
  {{[{{\lambda }_{c}}(t)]}_{U}}= & 0.00124429 
\end{align}</math>
 
 
For the instantaneous failure intensity:
 
::<math>\begin{align}
  {{[{{\lambda }_{i}}(t)]}_{L}}= & 0.00038775 \\
  {{[{{\lambda }_{c}}(t)]}_{U}}= & 0.00048125 
\end{align}</math>
 
 
The following figures show the graphs of the cumulative and instantaneous failure intensity. Both are plotted with confidence bounds.
 
[[Image:rga4.7.png|center|400px|Cumulative Failure Intensity plot with 2-sided 90% confidence bounds.]]
 
 
[[Image:rga4.8.png|center|400px|Instantaneous Failure Intensity plot with 2-sided 90% confidence bounds.]]
 
 
3.  The cumulative MTBF is:
 
::<math>\begin{align}
  {{m}_{c}}(T)= & 1.9453\cdot {{22000}^{0.6133}} \\
  = & 895.3395 
\end{align}</math>
 
 
And the instantaneous MTBF is:
 
::<math>\begin{align}
  {{m}_{i}}(T)= & \frac{1.9453}{1-0.6133}\cdot {{22000}^{0.6133}} \\
  = & 2314.9369 
\end{align}</math>
 
 
So, at 90% confidence level and for  <math>T=22,000\,\!</math>  hours, the confidence bounds on the cumulative MTBF are:
 
::<math>\begin{align}
  {{m}_{c}}{{(t)}_{l}}= & 803.6695 \\
  {{m}_{c}}{{(t)}_{u}}= & 997.4658 
\end{align}</math>
 
 
The confidence bounds for the instantaneous MTBF are:
 
::<math>\begin{align}
  {{m}_{i}}{{(t)}_{l}}= & 2077.9204 \\
  {{m}_{i}}{{(t)}_{u}}= & 2578.9886 
\end{align}</math>
 
 
The figure below displays the cumulative MTBF.
 
[[Image:rga4.9.png|center|400px|Cumulative MTBF plot with 2-sided 90% condfidence bounds.]]
 
The next figure displays the instantaneous MTBF. Both are plotted with confidence bounds.
 
[[Image:rga4.10.png|center|400px|Instantaneous MTBF plot with 2-sided 90% confidence bounds.]]


==More Examples==
==More Examples==
===Estimating the Time Required to Meet an MTBF Goal===
===Estimating the Time Required to Meet an MTBF Goal===
A prototype of a system was tested with design changes incorporated during the test. A total of 12 failures occurred. The data set is given in the following table.
{{:Failure Times - Duane Example}}
 
{|border="1" align="center" style="border-collapse: collapse;" cellpadding="5" cellspacing="5"
|+'''Developmental test data for Example 6'''
!Failure Number
!Cumulative Test Time(hours)
|-
|1 ||80
|-
|2 ||175
|-
|3 ||265
|-
|4 ||400
|-
|5 ||590
|-
|6|| 1100
|-
|7|| 1650
|-
|8|| 2010
|-
|9|| 2400
|-
|10|| 3380
|-
|11|| 5100
|-
|12|| 6400
|}
 
#Estimate the Duane parameters.
#Plot the cumulative and instantaneous MTBF curves.
#How many cumulative test and development hours are required to meet an ''instantaneous'' MTBF goal #of 500 hours?
#How many cumulative test and development hours are required to meet a ''cumulative'' MTBF goal of 500 hours?
 
'''Solution'''
 
1. The next figure shows the data entered into RGA along with the estimated Duane parameters.
 
[[Image:rga4.11.png|thumb|center|400px|Entered data and the estimated Duane parameters.]]
 
2. The following figure shows the cumulative and instantaneous MTBF curves.
 
[[Image:rga4.12.png|thumb|center|400px|The cumulative and instantaneous MTBF curves.]]
 
3. The next figure shows the cumulative test and development hours needed for an instantaneous MTBF goal of 500 hours.
 
[[Image:rga4.13.png|thumb|center|400px|Required test time for an instantaneous MTBF of 500 hours.]]
 
 
4. The figure below shows the cumulative test and development hours needed for a cumulative MTBF goal of 500 hours.
 
[[Image:rga4.14.png|thumb|center|400px|Required test time for a cumulative MTBF of 500 hours.]]
 
===Deciding Whether to Halt the Test ===
<<PER LISA: NEED TO GET SME TO CONFIRM THE NEW NAME FOR THIS EXAMPLE>>
 
Two identical systems were tested. Any design changes made to improve the reliability of these systems were incorporated into both systems when any system failed. A total of 29 failures occurred. The data set is given in the following table.
 
{|border="1" align="center" style="border-collapse: collapse;" cellpadding="5" cellspacing="5"
|+'''Developmental test data'''
!Failure Number
!Failed Unit
!Test Time Unit 1(hours)
!Test Time Unit 2 (hours)
|-
|1|| 1|| 0.2|| 2.0
|-
|2|| 2|| 1.7|| 2.9
|-
|3|| 2|| 4.5|| 5.2
|-
|4|| 2|| 5.8|| 9.1
|-
|5|| 2|| 17.3|| 9.2
|-
|6|| 2|| 29.3|| 24.1
|-
|7|| 1|| 36.5|| 61.1
|-
|8|| 2|| 46.3|| 69.6
|-
|9|| 1|| 63.6|| 78.1
|-
|10|| 2|| 64.4|| 85.4
|-
|11|| 1|| 74.3|| 93.6
|-
|12|| 1|| 106.6|| 103
|-
|13|| 2|| 195.2 ||117
|-
|14|| 2|| 235.1|| 134.3
|-
|15|| 1|| 248.7 ||150.2
|-
|16|| 2|| 256.8 ||164.6
|-
|17|| 2|| 261.1|| 174.3
|-
|18|| 2|| 299.4 ||193.2
|-
|19|| 1|| 305.3|| 234.2
|-
|20|| 1|| 326.9|| 257.3
|-
|21|| 1|| 339.2|| 290.2
|-
|22|| 1|| 366.1|| 293.1
|-
|23|| 2|| 466.4|| 316.4
|-
|24|| 1|| 504|| 373.2
|-
|25|| 1|| 510|| 375.1
|-
|26|| 2|| 543.2|| 386.1
|-
|27|| 2|| 635.4 ||453.3
|-
|28|| 1|| 641.2|| 485.8
|-
|29|| 2|| 755.8|| 573.6
|}


Do the following:
===Multiple Systems - Known Operating Times Example===
 
{{:Known_Operating_Times_-_Duane_Example}}
#Estimate the Duane parameters.
#Assume both units are tested for an additional 100 hours each. How many failures do you expect in that period?
#If testing/development were halted at this point, what would the reliability equation for this system be
 
'''Solution'''
 
:1) The figure below shows the data entered into RGA along with the estimated Duane parameters.
 
[[Image:rga4.15.png|thumb|center|400px|Entered data and the estimated parameters.]]
 
:2) The current accumulated test time for both units is 1329.4 hours. If the process were to continue for an additional combined time of 200 hours, the expected cumulative number of failures at  <math>T=1529.4\,\!</math>  is 31.2695, as shown in the figure below. At T = 1329.4, the expected number of failures is 29.2004. Therefore, the expected number of failures that would be observed over the additional 200 hours is  <math>31.2695-29.2004=2.0691\approx 2\,\!</math> .
 
[[Image:rga4.16.png|thumb|center|400px|The expected cumulative number of failures at <math>T=1529.4\,\!</math>.]]
 
:3) If testing/development were halted at this point, the system failure intensity would be equal to the instantaneous failure intensity at that time, or  <math>\lambda =0.0107\,\!</math>  failures/hour. See the following figure.
 
[[Image:rga4.17.png|thumb|center|400px|Calculate the instantaneous failure intensity at the end of the test.]]
 
An exponential distribution can be assumed since the value of the failure intensity at that instant in time is known. Therefore:
 
::<math>\begin{align}
  R(t)= & {{e}^{-\lambda t}} \\
= & {{e}^{-(0.0107)t}}
\end{align}</math>
 
Weibull++ can be utilized (from within RGA) to provide a Reliability vs. Time plot. This is shown in the following figure.
 
[[Image:rga4.18.png|thumb|center|400px|Reliability vs. Time plot.]]


===Using the Duane Model for Success/Failure Data===
===Using the Duane Model for Success/Failure Data===
Given the sequential success/failure data in the table below, do the following:
{{:Sequential Data - Duane Example}}
 
:1) Estimate the Duane parameters.
:2) What is the instantaneous MTBF at the end of the test?
:3) How many additional test runs with a one-sided 90% confidence level are required to meet an instantaneous MTBF goal of 5 hours?
 
{|border="1" align="center" style="border-collapse: collapse;" cellpadding="5" cellspacing="5"
|+'''Sequential data'''
!Run Number
!Result
|-
|1|| F
|-
|2|| F
|-
|3|| S
|-
|4|| S
|-
|5|| S
|-
|6|| F
|-
|7|| S
|-
|8|| F
|-
|9|| F
|-
|10|| S
|-
|11|| S
|-
|12|| S
|-
|13|| F
|-
|14|| S
|-
|15|| S
|-
|16|| S
|-
|17|| S
|-
|18|| S
|-
|19|| S
|-
|20|| S
|}
 
'''Solution'''
 
:1) The following figure shows the data set entered into RGA along with the estimated Duane parameters.
 
[[Image:rga4.19.png|thumb|center|400px|Entered data and the estimated parameters.]]
 
:2) The MTBF at the end of the test is equal to 4.5904 hours. Note that  this is the DMTBF that is shown in the control panel in the above figure.
:3) The figure below shows the number of test runs with both one-sided confidence bounds at 90% confidence level to achieve an instantaneous MTBF of 5 hours. Therefore, the number of additional test runs required with a 90% confidence level is equal to  <math>42.2481-20=22.2481\approx 23\,\!</math>  test runs.
 
[[Image:rga4.20.png|center|400px|Number of test runs with a one-sided 90% confidence level required to meet an instantaneous MTBF goal of 5 hours.]]

Latest revision as of 19:07, 8 August 2018

New format available! This reference is now available in a new format that offers faster page load, improved display for calculations and images, more targeted search and the latest content available as a PDF. As of September 2023, this Reliawiki page will not continue to be updated. Please update all links and bookmarks to the latest reference at help.reliasoft.com/reference/reliability_growth_and_repairable_system_analysis

Chapter 3.1: Duane Model


RGAbox.png

Chapter 3.1  
Duane Model  

Synthesis-icon.png

Available Software:
RGA

Examples icon.png

More Resources:
RGA examples

In 1962, J. T. Duane published a report in which he presented failure data of different systems during their development programs [8]. While analyzing the data, it was observed that the cumulative MTBF versus cumulative operating time followed a straight line when plotted on log-log paper, as shown next.

Cumulative MTBF vs. Cumulative Test Time postulated by Duane.

Based on that observation, Duane developed his model as follows. If [math]\displaystyle{ N(T)\,\! }[/math] is the number of failures by time [math]\displaystyle{ T\,\! }[/math], the observed mean (average) time between failures, [math]\displaystyle{ MTB{{F}_{c}},\,\! }[/math] at time [math]\displaystyle{ T\,\! }[/math] is:

[math]\displaystyle{ MTB{{F}_{c}}=\frac{T}{N(T)}\,\! }[/math]

The equation of the line can be expressed as:

[math]\displaystyle{ \begin{align} y=mx+c \end{align}\,\! }[/math]

Setting:

[math]\displaystyle{ \begin{align} y= & \ln (MTB{{F}_{c}}) \\ x= & \ln (T) \\ m= & \alpha \\ c= & \ln b \end{align}\,\! }[/math]

yields:

[math]\displaystyle{ \begin{align} \ln (MTB{{F}_{c}})=\alpha \ln (T)+\ln b \end{align}\,\! }[/math]

Then equating [math]\displaystyle{ MTB{{F}_{c}}\,\! }[/math] to its expected value, and assuming an exact linear relationship, gives:

[math]\displaystyle{ \begin{align} E(MTB{{F}_{c}})=b{{T}^{\alpha }} \end{align}\,\! }[/math]

or:

[math]\displaystyle{ \begin{align} MTB{{F}_{c}}=b{{T}^{\alpha }} \end{align}\,\! }[/math]

And, if you assume a constant failure intensity, then the cumulative failure intensity, [math]\displaystyle{ {{\lambda }_{c}}\,\! }[/math], is:

[math]\displaystyle{ E({{\lambda }_{c}})=\frac{1}{b}{{T}^{-\alpha }}\,\! }[/math]

or:

[math]\displaystyle{ {{\hat{{\bar{\lambda }}}}_{c}}=\frac{1}{b}{{T}^{-\alpha }}\,\! }[/math]

Also, the expected number of failures up to time [math]\displaystyle{ T\,\! }[/math] is:

[math]\displaystyle{ \begin{align} E(N(T))= & {{\hat{{\bar{\lambda }}}}_{c}}\cdot T \\ = & \frac{1}{b}{{T}^{1-\alpha }} \end{align}\,\! }[/math]

where:

  • [math]\displaystyle{ {{\hat{{\bar{\lambda }}}}_{c}}\,\! }[/math] is the average estimate of the cumulative failure intensity, failures/hour.
  • [math]\displaystyle{ T\,\! }[/math] is the total accumulated unit hours of test and/or development time.
  • [math]\displaystyle{ 1/b\,\! }[/math] is the cumulative failure intensity at [math]\displaystyle{ T = 1\,\! }[/math] or at the beginning of the test, or the earliest time at which the first [math]\displaystyle{ {{\hat{{\bar{\lambda }}}}}\,\! }[/math] is predicted, or the [math]\displaystyle{ {{\hat{{\bar{\lambda }}}}}\,\! }[/math] for the equipment at the start of the design and development process.
  • [math]\displaystyle{ \alpha\,\! }[/math]is the improvement rate in the [math]\displaystyle{ {{\hat{{\bar{\lambda }}}}}, 0\le \alpha \le 1\,\! }[/math].

The corresponding [math]\displaystyle{ MTB{{F}_{c}}\,\! }[/math], or [math]\displaystyle{ {{\hat{m}}_{c}}\,\! }[/math], is equal to:

[math]\displaystyle{ {{\hat{m}}_{c}}=b{{T}^{\alpha }}\,\! }[/math]

where [math]\displaystyle{ b=\,\! }[/math] cumulative MTBF at [math]\displaystyle{ T=1\,\! }[/math] or at the beginning of the test, or the earliest time at which the first [math]\displaystyle{ \hat{m}\,\! }[/math] can be determined, or the [math]\displaystyle{ \hat{m}\,\! }[/math] predicted at the start of the design and development process ( [math]\displaystyle{ b\gt 0\,\! }[/math] ).

The cumulative MTBF, [math]\displaystyle{ {{\hat{m}}_{c}}\,\! }[/math], and [math]\displaystyle{ {{\hat{{\bar{\lambda }}}}_{c}}\,\! }[/math] tell whether [math]\displaystyle{ m\,\! }[/math] is increasing or [math]\displaystyle{ \lambda \,\! }[/math] is decreasing with time, utilizing all data up to that time. You may want to know, however, the instantaneous [math]\displaystyle{ {{\hat{m}}_{i}}\,\! }[/math] or [math]\displaystyle{ {{\hat{{\bar{\lambda }}}}_{i}}\,\! }[/math] to see what you are doing at a specific instant or after a specific test and development time. The instantaneous failure intensity, [math]\displaystyle{ {{\lambda }_{i}}\,\! }[/math], is:

[math]\displaystyle{ \begin{align} {{\lambda }_{i}}= & \frac{d(E(N(T)))}{dT} \\ = & \frac{1}{b}(1-\alpha ){{T}^{-\alpha }} \\ = & (1-\alpha ){{\lambda }_{c}} \end{align}\,\! }[/math]

Similarly, using the equation for the expected number of failures up to time [math]\displaystyle{ T\,\! }[/math], this procedure yields:

[math]\displaystyle{ \begin{align} {{m}_{i}}= & \frac{1}{1-\alpha }b{{T}^{\alpha }} \\ = & \frac{1}{1-\alpha }{{{\hat{m}}}_{c}},:\ \ \alpha \not{=}1 \end{align}\,\! }[/math]

where [math]\displaystyle{ \alpha =1\,\! }[/math] implies infinite MTBF growth.

As shown in these derivations, the instantaneous failure intensity improvement line is obtained by shifting the cumulative failure intensity line down, parallel to itself, by a distance of [math]\displaystyle{ (1-\alpha )\,\! }[/math]. Similarly, the current or instantaneous MTBF growth line is obtained by shifting the cumulative MTBF line up, parallel to itself, by a distance of [math]\displaystyle{ \tfrac{1}{1-\alpha }\,\! }[/math], as illustrated in the figure below.

Cumulative MTBF vs. Cumulative Test Time postulated by Duane.

Parameter Estimation

The Duane model is a two parameter model. Therefore, to use this model as a basis for predicting the reliability growth that could be expected in an equipment development program, procedures must be defined for estimating these parameters as a function of equipment characteristics. Note that, while these parameters can be estimated for a given data set using curve-fitting methods, there exists no underlying theory for the Duane model that could provide a basis for a priori estimation.

One of the parameters of the Duane model is [math]\displaystyle{ \alpha\,\! }[/math]. The second parameter can be represented as [math]\displaystyle{ A\,\! }[/math] or [math]\displaystyle{ b\,\! }[/math] where [math]\displaystyle{ A=\frac{1}{b}\,\! }[/math]. There is an option within the Application Setup that allows you to determine whether to display [math]\displaystyle{ A\,\! }[/math] or [math]\displaystyle{ b\,\! }[/math] for the Duane model. All formulation within this reference uses the parameter [math]\displaystyle{ b\,\! }[/math].

DuaneShowAorb.png

Graphical Method

The Duane model for the cumulative failure intensity is:

[math]\displaystyle{ {{\hat{{\bar{\lambda }}}}_{c}}=\frac{1}{b}{{T}^{-\alpha }}\,\! }[/math]

This equation may be linearized by taking the natural log of both sides:

[math]\displaystyle{ \ln \left( {{\hat{{\bar{\lambda }}}}_{c}} \right)=\ln \left( \frac{1}{b} \right)-\alpha \ln (T)\,\! }[/math]

Consequently, plotting [math]\displaystyle{ \hat{{\bar{\lambda }}}\,\! }[/math] versus [math]\displaystyle{ T\,\! }[/math] on log-log paper will result in a straight line with a negative slope, such that:

  • [math]\displaystyle{ \ln \left ({\frac{1}{b}} \right)\,\! }[/math] is the y-intercept at [math]\displaystyle{ T = 1\,\! }[/math]
  • [math]\displaystyle{ \frac{1}{b}\,\! }[/math] is the cumulative failure intensity at [math]\displaystyle{ T = 1\,\! }[/math]
  • [math]\displaystyle{ \alpha\,\! }[/math] is the slope of the straight line on the log-log plot

Similarly, the corresponding MTBF of the cumulative failure intensity can also be linearized by taking the natural log of both sides:

[math]\displaystyle{ \begin{align} \hat{m_{c}}&=bT^{\alpha } \\ \ln \hat{m_{c}}&=\ln b+\alpha \ln T \\ \end{align}\,\! }[/math]

Plotting [math]\displaystyle{ \hat{m}\,\! }[/math] versus [math]\displaystyle{ T\,\! }[/math] on log-log paper will result in a straight line with a positive slope such that:

  • [math]\displaystyle{ \ln{b}\,\! }[/math] is the y-intercept at [math]\displaystyle{ T = 1\,\! }[/math]
  • [math]\displaystyle{ b\,\! }[/math] is the cumulative mean time between failure at [math]\displaystyle{ T = 1\,\! }[/math]
  • [math]\displaystyle{ \alpha\,\! }[/math] is the slope of the straight line on the log-log plot

Two ways of determining these curves are as follows:

1. Predict the [math]\displaystyle{ {{\hat{{\bar{\lambda }}}}_{0}}\,\! }[/math] and [math]\displaystyle{ \hat{m}=\,\! }[/math] [math]\displaystyle{ \tfrac{1}{{{\hat{{\bar{\lambda }}}}_{0}}}\,\! }[/math] of the system from its reliability block diagram and available component failure intensities. Plot this value on log-log plotting paper at [math]\displaystyle{ T=1.\,\! }[/math] From past experience and from past data for similar equipment, find values of [math]\displaystyle{ {{\alpha }_{1}}\,\! }[/math], the slope of the improvement lines for [math]\displaystyle{ \hat{{\bar{\lambda }}}\,\! }[/math] or [math]\displaystyle{ \hat{m}\,\! }[/math]. Modify this [math]\displaystyle{ \alpha \,\! }[/math] as necessary. If a better design effort is expected and a more intensive research, test and development or TAAF program is to be implemented, then a 15% improvement in the growth rate may be attainable. Consequently, the available value for slope [math]\displaystyle{ \alpha \,\! }[/math], and [math]\displaystyle{ {{\alpha }_{1}}\,\! }[/math], should be adjusted by this amount. The value to be used will then be [math]\displaystyle{ \alpha =1.15{{\alpha }_{1}}.\,\! }[/math] A line is then drawn through point [math]\displaystyle{ {{\hat{{\bar{\lambda }}}}_{0}}\,\! }[/math] and [math]\displaystyle{ T=1\,\! }[/math] with the just determined slope [math]\displaystyle{ \alpha \,\! }[/math], keeping in mind that [math]\displaystyle{ \alpha \,\! }[/math] is negative for the [math]\displaystyle{ \hat{{\bar{\lambda }}}\,\! }[/math] curve. This line should be extended to the design, development and test time scheduled to be expended to see if the failure intensity goal will indeed be achieved on schedule. It is also possible to find that the design, development and test time to achieve the goal may be earlier than the delivery date or later. If earlier, then either the reliability program effort can be judiciously and appropriately trimmed; or if it is an incentive contract, full advantage is taken of the fact that the failure intensity goal can be exceeded with the associated increased profits to the company. A similar approach may be used for the MTBF growth model, where [math]\displaystyle{ {{\hat{m}}_{0}}=\tfrac{1}{{{\hat{{\bar{\lambda }}}}_{0}}}\,\! }[/math] is plotted at [math]\displaystyle{ T=1\,\! }[/math], and a line is drawn through the point [math]\displaystyle{ {{\hat{m}}_{0}}\,\! }[/math] and [math]\displaystyle{ T=1\,\! }[/math] with slope [math]\displaystyle{ \alpha \,\! }[/math] to obtain the MTBF growth line. If [math]\displaystyle{ \alpha \,\! }[/math] values are not available, consult the table below, which gives actual [math]\displaystyle{ \alpha \,\! }[/math] values for various types of equipment. These have been obtained from literature or by MTBF growth tests. It may be seen from the following table that [math]\displaystyle{ \alpha \,\! }[/math] values range between 0.24 and 0.65. The lower values reflect slow early growth and the higher values reflect fast early growth.

Sample Slope Values for Various Equipment
Equipment Slope([math]\displaystyle{ \alpha\,\! }[/math])
Computer system Actual 0.24
Easy to find failures were eliminated 0.26
All known failure causes were eliminated 0.36
Mainframe computer 0.50
Aerospace electronics All malfunctions 0.57
Relevant failures only 0.65
Attack radar 0.60
Rocket engine 0.46
Afterburning turbojet 0.35
Complex hydromechanical system 0.60
Aircraft generator 0.38
Modern dry turbojet 0.48

2. During the design, development and test phase and at specific milestones, the [math]\displaystyle{ \hat{{\bar{\lambda }}}=\tfrac{1}{{\hat{m}}}\,\! }[/math] is calculated from the total failures and [math]\displaystyle{ T\,\! }[/math] values. These values of [math]\displaystyle{ \hat{{\bar{\lambda }}}\,\! }[/math] or [math]\displaystyle{ \hat{m}\,\! }[/math] are plotted above the corresponding [math]\displaystyle{ T\,\! }[/math] values on log-log paper. A straight line is drawn favoring these points to minimize the distance between the points and the line, thus establishing the improvement or growth model and its parameters graphically. If needed, linear regression analysis techniques can be used to determine these parameters.

Graphical Method Example

A complex system's reliability growth is being monitored and the data set is given in the table below.

Cumulative Test Hours and the Corresponding Observed Failures for the Complex System
Point Number Cumulative Test Time(hours) Cumulative Failures Cumulative MTBF(hours) Instantaneous MTBF(hours)
1 200 2 100.0 100
2 400 3 133.0 200
3 600 4 150.0 200
4 3,000 11 273.0 342.8

Do the following:

  1. Plot the cumulative MTBF growth curve.
  2. Write the equation of this growth curve.
  3. Write the equation of the instantaneous MTBF growth model.
  4. Plot the instantaneous MTBF growth curve.

Solution

  1. Given the data in the second and third columns of the above table, the cumulative MTBF, [math]\displaystyle{ {{\hat{m}}_{c}}\,\! }[/math], values are calculated in the fourth column. The information in the second and fourth columns are then plotted. The first figure below shows the cumulative MTBF while the second figure below shows the instantaneous MTBF. It can be seen that a straight line represents the MTBF growth very well on log-log scales.
    Rga4.2.png
    Cumulative MTBF plot
    Rga4.3.png
    Instantaneous MTBF plot

    By changing the x-axis scaling, you are able to extend the line to [math]\displaystyle{ T=1\,\! }[/math]. You can get the value of [math]\displaystyle{ b\,\! }[/math] from the graph by positioning the cursor at the point where the line meets the y-axis. Then read the value of the y-coordinate position at the bottom left corner. In this case, [math]\displaystyle{ b\,\! }[/math] is approximately 14 hours. The next figure illustrates this.

    Rga4.4.png
    Cumulative MTBF plot for [math]\displaystyle{ b \approx 14\,\! }[/math] at [math]\displaystyle{ T=1\,\! }[/math]

    Another way of determining [math]\displaystyle{ b\,\! }[/math] is to calculate [math]\displaystyle{ \alpha \,\! }[/math] by using two points on the fitted straight line and substituting the corresponding [math]\displaystyle{ {{\hat{m}}_{c}}\,\! }[/math] and [math]\displaystyle{ T\,\! }[/math] values into:

    [math]\displaystyle{ \alpha =\frac{\ln \left( {{{\hat{m}}}_{{{c}_{2}}}} \right)-\ln \left( {{{\hat{m}}}_{{{c}_{1}}}} \right)}{\ln \left( {{T}_{_{2}}} \right)-\ln \left( {{T}_{_{1}}} \right)}\,\! }[/math]

    Then substitute this [math]\displaystyle{ \alpha \,\! }[/math] and choose a set of values for [math]\displaystyle{ {{\hat{m}}_{{{c}_{1}}}}\,\! }[/math] and [math]\displaystyle{ {{T}_{_{1}}}\,\! }[/math] into the cumulative MTBF equation, [math]\displaystyle{ {{\hat{m}}_{c}}=b{{T}^{\alpha }}\,\! }[/math], and solve for [math]\displaystyle{ b\,\! }[/math]. The slope of the line, [math]\displaystyle{ \alpha \,\! }[/math], may also be found from the linearized form of the cumulative MTBF equation, or :

    [math]\displaystyle{ \alpha =\frac{\ln \left( {{{\hat{m}}}_{c}} \right)-\ln (b)}{\ln (T)-\ln (1)}\,\! }[/math]

    Using the cumulative MTBF plot for the example, at [math]\displaystyle{ {{T}_{_{1}}}=200\,\! }[/math] hours, [math]\displaystyle{ {{\hat{m}}_{{{c}_{1}}}}=100\,\! }[/math] hours, and [math]\displaystyle{ {{T}_{_{2}}}=3,500\,\! }[/math] hours, [math]\displaystyle{ {{\hat{m}}_{{{c}_{2}}}}=300\,\! }[/math] hours. From the cumulative MTBF plot for [math]\displaystyle{ b=14\,\! }[/math] hours when [math]\displaystyle{ T=1\,\! }[/math], substituting the first set of values, [math]\displaystyle{ b=14\,\! }[/math] hours and [math]\displaystyle{ \ln 1=0\,\! }[/math], into the equation yields:

    [math]\displaystyle{ \begin{align} {{\alpha }_{1}}= & \frac{\ln (100)-\ln (14)}{\ln (200)-\ln (1)} \\ = & 0.3711 \end{align}\,\! }[/math]
  2. Substituting the second set of values, [math]\displaystyle{ b=14\,\! }[/math] hours and [math]\displaystyle{ \ln 1=0,\,\! }[/math] into the equation yields:
    [math]\displaystyle{ \begin{align} {{\alpha }_{2}}= & \frac{\ln (300)-\ln (14)}{\ln (3,500)-\ln (1)} \\ = & 0.3755 \end{align}\,\! }[/math]
    Averaging these two [math]\displaystyle{ \alpha \,\! }[/math] values yields a better estimate of [math]\displaystyle{ \hat{\alpha }=0.3733\,\! }[/math].
  3. Now the equation for the cumulative MTBF growth curve is:
    [math]\displaystyle{ {{\hat{m}}_{c}}=14\cdot {{T}^{\text{ }0.3733}}\,\! }[/math]
  4. Using the following equation for the instantaneous MTBF, or
    [math]\displaystyle{ {{m}_{i}} = \frac{1}{1-\alpha }{{{\hat{m}}}_{c}},:\ \ \alpha \not{=}1 \,\! }[/math]
    The equation for the instantaneous MTBF growth curve is:
    [math]\displaystyle{ \begin{align} {{\hat{m}}_{i}}=\frac{1}{1-0.3733} \cdot {{14T}^{0.3733}} \end{align}\,\! }[/math]
    The above equation is plotted in the instantaneous MTBF plot shown in the example and in the cumulative and instantaneous MTBF vs. Time plot. In the following figure, you can see that a parallel shift upward of the cumulative MTBF, [math]\displaystyle{ {{\hat{m}}_{c}}\,\! }[/math], line by a distance of [math]\displaystyle{ \tfrac{1}{1-\alpha }\,\! }[/math] gives the instantaneous MTBF, or the [math]\displaystyle{ {{\hat{m}}_{i}}\,\! }[/math], line.
    Cumulative and Instantaneous MTBF vs. Time plot.
    Cumulative and Instantaneous MTBF vs. Time plot

Least Squares (Linear Regression)

The parameters can also be estimated using a mathematical approach. To do this, linearize the MTBF of the cumulative failure intensity by taking the natural log of both sides, and then apply least squares analysis. For example:

[math]\displaystyle{ \begin{align} \hat{m_{c}}&=bT^{\alpha } \\ \ln \hat{m_{c}}&=\ln b+\alpha \ln T \\ \end{align}\,\! }[/math]

For simplicity in the calculations, let:

[math]\displaystyle{ \begin{align} \ln ({{m}_{ci}})= & {{Y}_{i}} \\ \ln (b)= & a \\ \alpha = & c \\ \ln ({{T}_{i}})= & {{X}_{i}} \end{align}\,\! }[/math]

Therefore, the equation becomes:

[math]\displaystyle{ {{Y}_{i}}=\hat{a}+\hat{c}{{X}_{i}}\,\! }[/math]

Assume that a set of data pairs [math]\displaystyle{ ({{X}_{1}},{{Y}_{1}})\,\! }[/math], [math]\displaystyle{ ({{X}_{2}},{{Y}_{2}})\,\! }[/math],..., [math]\displaystyle{ ({{X}_{N}},{{Y}_{N}})\,\! }[/math] were obtained and plotted. Then according to the Least Squares Principle, which minimizes the vertical distance between the data points and the straight line fitted to the data, the best fitting straight line to this data set is the straight line [math]\displaystyle{ Y=\hat{a}+\hat{c}X\,\! }[/math] such that:

[math]\displaystyle{ \underset{i=1}{\overset{N}{\mathop \sum }}\,{{(\hat{a}+\hat{c}{{X}_{i}}-{{Y}_{i}})}^{2}}=\underset{(a,c)}{\mathop{min}}\,\underset{i=1}{\overset{N}{\mathop \sum }}\,{{(a+c{{X}_{i}}-{{Y}_{i}})}^{2}}\,\! }[/math]

where [math]\displaystyle{ \hat{a}\,\! }[/math] and [math]\displaystyle{ \hat{c}\,\! }[/math] are the least squares estimates of [math]\displaystyle{ a\,\! }[/math] and [math]\displaystyle{ c\,\! }[/math]. To obtain [math]\displaystyle{ \hat{a}\,\! }[/math] and [math]\displaystyle{ \hat{c}\,\! }[/math], let:

[math]\displaystyle{ F=\underset{i=1}{\overset{N}{\mathop \sum }}\,{{(a+c{{X}_{i}}-{{Y}_{i}})}^{2}}\,\! }[/math]

Differentiating [math]\displaystyle{ F\,\! }[/math] with respect to [math]\displaystyle{ a\,\! }[/math] and [math]\displaystyle{ c\,\! }[/math] yields:

[math]\displaystyle{ \frac{\partial F}{\partial a}=2\underset{i=1}{\overset{N}{\mathop \sum }}\,(a+c{{X}_{i}}-{{Y}_{i}})\,\! }[/math]

and:

[math]\displaystyle{ \frac{\partial F}{\partial c}=2\underset{i=1}{\overset{N}{\mathop \sum }}\,(a+c{{X}_{i}}-{{Y}_{i}}){{X}_{i}}\,\! }[/math]

Set those two equations equal to zero:

[math]\displaystyle{ \underset{i=1}{\overset{N}{\mathop \sum }}\,(a+c{{X}_{i}}-{{Y}_{i}})=\underset{i=1}{\overset{N}{\mathop \sum }}\,(\hat{{{Y}_{i}}}-{{Y}_{i}})=-\underset{i=1}{\overset{N}{\mathop \sum }}\,({{Y}_{i}}-\hat{{{Y}_{i}}})=0\,\! }[/math]

and:

[math]\displaystyle{ \underset{i=1}{\overset{N}{\mathop \sum }}\,(a+c{{X}_{i}}-{{Y}_{i}}){{X}_{i}}=\underset{i=1}{\overset{N}{\mathop \sum }}\,(\hat{{{Y}_{i}}}-{{Y}_{i}}){{X}_{i}}=-\underset{i=1}{\overset{N}{\mathop \sum }}\,({{Y}_{i}}-\hat{{{Y}_{i}}}){{X}_{i}}=0\,\! }[/math]

Solve the equations simultaneously:

[math]\displaystyle{ \begin{align} \hat{a}= & \frac{\sum\limits_{i=1}^{N}{{{Y}_{i}}}}{N}-\hat{c}\frac{\sum\limits_{i=1}^{N}{{{X}_{i}}}}{N}\\ = & \bar{Y}-\hat{c}\bar{X}\end{align} \,\! }[/math]

and:

[math]\displaystyle{ \hat{c}=\frac{\underset{i=1}{\overset{N}{\mathop{\sum }}}\,{{X}_{i}}{{Y}_{i}}-\tfrac{\left( \underset{i=1}{\overset{N}{\mathop{\sum }}}\,{{X}_{i}}\underset{i=1}{\overset{N}{\mathop{\sum }}}\,{{Y}_{i}} \right)}{N}}{\underset{i=1}{\overset{N}{\mathop{\sum }}}\,X_{i}^{2}-\tfrac{{{\left( \underset{i=1}{\overset{N}{\mathop{\sum }}}\,{{X}_{i}} \right)}^{2}}}{N}}\,\! }[/math]

Now substituting back [math]\displaystyle{ \ln ({{m}_{ci}})={{Y}_{i}},\,\! }[/math] [math]\displaystyle{ \ln (b)=a,\,\! }[/math] [math]\displaystyle{ \alpha =c\,\! }[/math] and [math]\displaystyle{ \ln ({{T}_{i}})={{X}_{i}},\,\! }[/math] we have:

[math]\displaystyle{ \hat{b}={{e}^{\tfrac{1}{n}\left[ \underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{m}_{ci}})-\alpha \underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{T}_{i}}) \right]}}\,\! }[/math]

where:

[math]\displaystyle{ \hat{\alpha }=\frac{\underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{T}_{i}})\ln ({{m}_{ci}})-\tfrac{\underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{T}_{i}})\underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{m}_{ci}})}{n}}{\underset{i=1}{\overset{n}{\mathop{\sum }}}\,{{\left[ \ln ({{T}_{i}}) \right]}^{2}}-\tfrac{{{\left( \underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{T}_{i}}) \right)}^{2}}}{n}}\,\! }[/math]


Example 1

Using the same data set from the graphical approach example, estimate the parameters of the MTBF model using least squares.


Solution

From the data table:

[math]\displaystyle{ \begin{align} \underset{i=1}{\overset{n}{\mathop \sum }}\,\ln ({{T}_{i}})&= & 25.693 \\ \underset{i=1}{\overset{n}{\mathop \sum }}\,\ln ({{T}_{i}})\ln ({{m}_{ci}})&= & 130.66 \\ \underset{i=1}{\overset{n}{\mathop \sum }}\,\ln ({{m}_{ci}})&= & 20.116 \\ \underset{i=1}{\overset{n}{\mathop \sum }}\,{{\left[ \ln ({{T}_{i}}) \right]}^{2}}&= & 168.99 \end{align}\,\! }[/math]

Obtain the value of [math]\displaystyle{ \hat{\alpha}\,\! }[/math] from the least squares analysis, or:

[math]\displaystyle{ \begin{align} \hat{\alpha }&=\frac{\underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{T}_{i}})\ln ({{m}_{ci}})-\tfrac{\underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{T}_{i}})\underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{m}_{ci}})}{n}}{\underset{i=1}{\overset{n}{\mathop{\sum }}}\,{{\left[ \ln ({{T}_{i}}) \right]}^{2}}-\tfrac{{{\left( \underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{T}_{i}}) \right)}^{2}}}{n}} \\ & = \frac{130.66-\tfrac{25.693\cdot 20.116}{4}}{168.99-\tfrac{{{25.693}^{2}}}{4}} \\ & = 0.3671 \end{align}\,\! }[/math]

Obtain the value [math]\displaystyle{ \hat{b}\,\! }[/math] from the least squares analysis, or:

[math]\displaystyle{ \begin{align} \hat{b}&={{e}^{\tfrac{1}{n}\left[ \underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{m}_{ci}})-\alpha \underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{T}_{i}}) \right]}} \\ & = {{e}^{\tfrac{1}{4}(20.116-0.3671\cdot 25.693)}} \\ & = 14.456 \end{align}\,\! }[/math]

Therefore, the cumulative MTBF becomes:

[math]\displaystyle{ \begin{align} \hat{m_{c}}&=bT^{\alpha } \\ &=14.456\cdot {{T}^{0.3671}} \\ \end{align}\,\! }[/math]

The equation for the instantaneous MTBF growth curve is:

[math]\displaystyle{ \begin{align} {{\hat{m}}_{i}}&=\frac{1}{1-\alpha }{{{\hat{m}}}_{c}},:\ \ \alpha \not{=}1 \\ &=\frac{1}{1-0.3671}(14.456){{T}^{0.3671}} \\ \end{align}\,\! }[/math]


Example 2

For the data given in columns 1 and 2 of the following table, estimate the Duane parameters using least squares.

Failure Times Data
(1)Failure Number (2)Failure Time(hours) (3)[math]\displaystyle{ \ln{T_i}\,\! }[/math] (4)[math]\displaystyle{ \ln{T_i}^2\,\! }[/math] (5)[math]\displaystyle{ m_c\,\! }[/math] (6)[math]\displaystyle{ \ln{m_c}\,\! }[/math] (7)[math]\displaystyle{ \ln{m_c}\cdot\ln{T_i}\,\! }[/math]
1 9.2 2.219 4.925 9.200 2.219 4.925
2 25 3.219 10.361 12.500 2.526 8.130
3 61.5 4.119 16.966 20.500 3.020 12.441
4 260 5.561 30.921 65.000 4.174 23.212
5 300 5.704 32.533 60.000 4.094 23.353
6 710 6.565 43.103 118.333 4.774 31.339
7 916 6.820 46.513 130.857 4.874 33.241
8 1010 6.918 47.855 126.250 4.838 33.470
9 1220 7.107 50.504 135.556 4.909 34.889
10 2530 7.836 61.402 253.000 5.533 43.359
11 3350 8.117 65.881 304.545 5.719 46.418
12 4200 8.343 69.603 350.000 5.858 48.872
13 4410 8.392 70.419 339.231 5.827 48.895
14 4990 8.515 72.508 356.429 5.876 50.036
15 5570 8.625 74.393 371.333 5.917 51.036
16 8310 9.025 81.455 519.375 6.253 56.431
17 8530 9.051 81.927 501.765 6.218 56.282
18 9200 9.127 83.301 511.111 6.237 56.921
19 10500 9.259 85.731 552.632 6.315 58.469
20 12100 9.401 88.378 605.000 6.405 60.215
21 13400 9.503 90.307 638.095 6.458 61.375
22 14600 9.589 91.945 663.636 6.498 62.305
23 22000 9.999 99.976 956.522 6.863 68.625
Sum = 173.013 1400.908 7600.870 121.406 974.242

Solution

To estimate the parameters using least squares, the values in columns 3, 4, 5, 6 and 7 are calculated. The cumulative MTBF, [math]\displaystyle{ {{m}_{c}}\,\! }[/math], is calculated by dividing the failure time by the failure number. The value of [math]\displaystyle{ \hat{\alpha }\,\! }[/math] is:

[math]\displaystyle{ \begin{align} \hat{\alpha }&=\frac{\underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{T}_{i}})\ln ({{m}_{ci}})-\tfrac{\underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{T}_{i}})\underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{m}_{ci}})}{n}}{\underset{i=1}{\overset{n}{\mathop{\sum }}}\,{{\left[ \ln ({{T}_{i}}) \right]}^{2}}-\tfrac{{{\left( \underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{T}_{i}}) \right)}^{2}}}{n}} \\ & = \frac{974.242-\tfrac{173.013\cdot 121.406}{23}}{1400.908-\tfrac{{{(173.013)}^{2}}}{23}} \\ & = 0.6133 \end{align}\,\! }[/math]

The estimator of [math]\displaystyle{ b\,\! }[/math] is estimated to be:

[math]\displaystyle{ \begin{align} \hat{b}&={{e}^{\tfrac{1}{n}\left[ \underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{m}_{ci}})-\alpha \underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{T}_{i}}) \right]}} \\ & = {{e}^{\tfrac{1}{23}(121.406-0.6133\cdot 173.013)}} \\ & = 1.9453 \end{align}\,\! }[/math]

Therefore, the cumulative MTBF becomes:

[math]\displaystyle{ \begin{align} \hat{m_{c}}&= bT^{\alpha } \\ & =1.9453\cdot {{T}^{0.613}} \\ \end{align}\,\! }[/math]

Using the equation for the instantaneous MTBF growth curve,

[math]\displaystyle{ \begin{align} {{\hat{m}}_{i}}&=\frac{1}{1-\alpha }{{{\hat{m}}}_{c}},:\ \ \alpha \not{=}1 \\ & =\frac{1}{1-0.613}(1.945){{T}^{0.613}} \\ \end{align}\,\! }[/math]
Rga4.6.png


Example 3

For the data given in the following table, estimate the Duane parameters using least squares.

Multiple Systems (Known Operating Times) Data}
Run Number Failed Unit Test Time 1 Test Time 2 Cumulative Time
1 1 0.2 2.0 2.2
2 2 1.7 2.9 4.6
3 2 4.5 5.2 9.7
4 2 5.8 9.1 14.9
5 2 17.3 9.2 26.5
6 2 29.3 24.1 53.4
7 1 36.5 61.1 97.6
8 2 46.3 69.6 115.9
9 1 63.6 78.1 141.7
10 2 64.4 85.4 149.8
11 1 74.3 93.6 167.9
12 1 106.6 103 209.6
13 2 195.2 117 312.2
14 2 235.1 134.3 369.4
15 1 248.7 150.2 398.9
16 2 256.8 164.6 421.4
17 2 261.1 174.3 435.4
18 2 299.4 193.2 492.6
19 1 305.3 234.2 539.5
20 1 326.9 257.3 584.2
21 1 339.2 290.2 629.4
22 1 366.1 293.1 659.2
23 2 466.4 316.4 782.8
24 1 504 373.2 877.2
25 1 510 375.1 885.1
26 2 543.2 386.1 929.3
27 2 635.4 453.3 1088.7
28 1 641.2 485.8 1127
29 2 755.8 573.6 1329.4

Solution

The solution to this example follows the same procedure as the previous example. Therefore, from the table shown above:

[math]\displaystyle{ \begin{align} \underset{i=1}{\overset{29}{\mathop \sum }}\,\ln ({{T}_{i}})= & 154.151 \\ \underset{i=1}{\overset{29}{\mathop \sum }}\,\ln {{({{T}_{i}})}^{2}}= & 902.592 \\ \underset{i=1}{\overset{29}{\mathop \sum }}\,\ln ({{m}_{c}})= & 82.884 \\ \underset{i=1}{\overset{29}{\mathop \sum }}\,\ln ({{T}_{i}})\cdot \ln ({{m}_{c}})= & 483.154 \end{align}\,\! }[/math]

For least squares, the value of [math]\displaystyle{ \alpha \,\! }[/math] is:

[math]\displaystyle{ \begin{align} \hat{\alpha }&=\frac{\underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{T}_{i}})\ln ({{m}_{ci}})-\tfrac{\underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{T}_{i}})\underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{m}_{ci}})}{n}}{\underset{i=1}{\overset{n}{\mathop{\sum }}}\,{{\left[ \ln ({{T}_{i}}) \right]}^{2}}-\tfrac{{{\left( \underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{T}_{i}}) \right)}^{2}}}{n}} \\ & = \frac{483.154-\tfrac{154.151\cdot 82.884}{29}}{902.592-\tfrac{{{(154.151)}^{2}}}{29}} \\ & = 0.5115 \end{align}\,\! }[/math]

The value of the estimator [math]\displaystyle{ b\,\! }[/math] is:

[math]\displaystyle{ \begin{align} \hat{b}&={{e}^{\tfrac{1}{n}\left[ \underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{m}_{ci}})-\alpha \underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{T}_{i}}) \right]}} \\ & = {{e}^{\tfrac{1}{29}(82.884-0.5115\cdot 154.151)}} \\ & = 1.1495 \end{align}\,\! }[/math]

Therefore, the cumulative MTBF is:

[math]\displaystyle{ \begin{align} \hat{m_{c}}&=bT^{\alpha } & = 1.1495\cdot {{T}^{0.5115}} \end{align}\,\! }[/math]

Using the equation for the instantaneous MTBF growth,

[math]\displaystyle{ \begin{align} {{\hat{m}}_{i}}&=\frac{1}{1-\alpha }{{{\hat{m}}}_{c}},:\ \ \alpha \not{=}1 \\ & =\frac{1}{1-0.5115}(1.1495){{T}^{0.5115}} \end{align}\,\! }[/math]

Maximum Likelihood Estimators

L. H. Crow [17] noted that the Duane model could be stochastically represented as a Weibull process, allowing for statistical procedures to be used in the application of this model in reliability growth. This statistical extension became what is known as the Crow-AMSAA (NHPP) model. The Crow-AMSAA model, which is described in the Crow-AMSAA (NHPP) chapter, provides a complete Maximum Likelihood Estimation (MLE) solution to the Duane model.

Confidence Bounds

Least squares confidence bounds can be computed for both the model parameters and metrics of interest for the Duane model.

Parameter Bounds

Apply least squares analysis on the Duane model:

[math]\displaystyle{ \ln ({{\hat{m}}_{c}})=\ln (b)+\alpha \ln (t)\,\! }[/math]

The unbiased estimator of [math]\displaystyle{ {{\sigma}^{2}}\,\! }[/math] can be obtained from:

[math]\displaystyle{ {{\sigma }^{2}}=Var\left[ \ln {{m}_{c}}(t) \right]=\frac{SSE}{(n-2)}\,\! }[/math]

where:

[math]\displaystyle{ SSE=\underset{i=1}{\overset{n}{\mathop \sum }}\,{{\left[ \ln {{{\hat{m}}}_{c}}({{t}_{i}})-\ln {{m}_{c}}({{t}_{i}}) \right]}^{2}}\,\! }[/math]

Thus, the confidence bounds on [math]\displaystyle{ \alpha \,\! }[/math] and [math]\displaystyle{ b\,\! }[/math] are:

[math]\displaystyle{ C{{B}_{\alpha }}=\hat{\alpha }\pm {{t}_{n-2,\alpha /2}}SE(\hat{\alpha })\,\! }[/math]
[math]\displaystyle{ C{{B}_{b}}=\hat{b}{{e}^{\pm {{t}_{n-2,\alpha /2}}SE\left[ \ln (\hat{b}) \right]}}\,\! }[/math]

where [math]\displaystyle{ {{t}_{n-2,\alpha /2}}\,\! }[/math] denotes the percentage point of the [math]\displaystyle{ t\,\! }[/math] distribution with [math]\displaystyle{ n-2\,\! }[/math] degrees of freedom such that [math]\displaystyle{ P\{{{t}_{n-2}}\ge {{t}_{\alpha /2,n-2}}\}=\alpha /2\,\! }[/math] and:

[math]\displaystyle{ SE(\hat{\alpha })=\frac{\sigma }{\sqrt{{{S}_{xx}}}}\,\! }[/math]
[math]\displaystyle{ SE\left[ \ln (\hat{b}) \right]=\sigma \cdot \sqrt{\frac{\underset{i=1}{\overset{n}{\mathop{\sum }}}\,{{(\ln {{t}_{i}})}^{2}}}{n\cdot {{S}_{xx}}}}\,\! }[/math]
[math]\displaystyle{ {{S}_{xx}}=\left[ \underset{i=1}{\overset{n}{\mathop \sum }}\,{{(\ln {{t}_{i}})}^{2}} \right]-\frac{1}{n}{{\left( \underset{i=1}{\overset{n}{\mathop \sum }}\,\ln ({{t}_{i}}) \right)}^{2}}\,\! }[/math]

Other Bounds

Confidence bounds also can be obtained on the cumulative MTBF and the cumulative failure intensity:

[math]\displaystyle{ C{{B}_{{{m}_{c}}}}={{\hat{m}}_{c}}(t){{e}^{\pm {{z}_{\alpha }}\sqrt{Var\left[ \ln ({{{\hat{m}}}_{c}}) \right]}}}\,\! }[/math]
[math]\displaystyle{ Var\left[ \ln ({{{\hat{m}}}_{c}}) \right]=\frac{\sum\limits_{i=1}^{n}{{{\left( \ln {{{\hat{m}}}_{c}}({{t}_{i}})-\ln {{m}_{c}}({{t}_{i}}) \right)}^{2}}}}{n-2}\cdot \left( \frac{1}{n}+\frac{{{\left( \ln (t)-\frac{\sum\limits_{i=1}^{n}{\ln ({{t}_{i}})}}{n} \right)}^{2}}}{\sum\limits_{i=1}^{n}{{{\left( \ln ({{t}_{i}})-\frac{\sum\limits_{i=1}^{n}{\ln ({{t}_{i}})}}{n} \right)}^{2}}}} \right)\,\! }[/math]
[math]\displaystyle{ \begin{align} {{[{{\lambda }_{c}}(t)]}_{L}}= & \frac{1}{{{[{{m}_{c}}(t)]}_{u}}} \\ {{[{{\lambda }_{c}}(t)]}_{U}}= & \frac{1}{{{[{{m}_{c}}(t)]}_{l}}} \end{align}\,\! }[/math]

When [math]\displaystyle{ n\,\! }[/math] is large, the approximate [math]\displaystyle{ 100(1-\alpha )%\,\! }[/math] confidence bounds for instantaneous MTBF are given by:

[math]\displaystyle{ \begin{align} {{m}_{i}}{{(t)}_{L}}= & \frac{{{[{{m}_{c}}(t)]}_{L}}}{{\hat{\beta }}} \\ {{m}_{i}}{{(t)}_{U}}= & \frac{{{[{{m}_{c}}(t)]}_{U}}}{{\hat{\beta }}} \end{align}\,\! }[/math]

and

[math]\displaystyle{ \lambda_{i}(t) = \frac {1}{m_{i}(t)}\,\! }[/math]

therefore, the confidence bounds on the instantaneous failure intensity are:

[math]\displaystyle{ \begin{align} {{[{{\lambda }_{i}}(t)]}_{L}}= & \frac{1}{{{[{{m}_{i}}(t)]}_{U}}} \\ {{[{{\lambda }_{c}}(t)]}_{U}}= & \frac{1}{{{[{{m}_{i}}(t)]}_{L}}} \end{align}\,\! }[/math]

Duane Confidence Bounds Example

Using the values of [math]\displaystyle{ \hat{b}\,\! }[/math] and [math]\displaystyle{ \hat{\alpha }\,\! }[/math] estimated from the least squares analysis in Least Squares Example 2:

[math]\displaystyle{ \hat{b}=1.9453\,\! }[/math]
[math]\displaystyle{ \hat{\alpha}=0.6133\,\! }[/math]

Calculate the 90% confidence bounds for the following:

  1. The parameters [math]\displaystyle{ \alpha\,\! }[/math] and [math]\displaystyle{ b\,\! }[/math].
  2. The cumulative and instantaneous failure intensity.
  3. The cumulative and instantaneous MTBF.

Solution

  1. Use the values of [math]\displaystyle{ \hat{b}\,\! }[/math] and [math]\displaystyle{ \hat{\alpha }\,\! }[/math] estimated from the least squares analysis. Then:
    [math]\displaystyle{ \begin{align} {{S}_{xx}}&=\left[ \underset{i=1}{\overset{n}{\mathop \sum }}\,{{(\ln {{t}_{i}})}^{2}} \right]-\frac{1}{n}{{\left( \underset{i=1}{\overset{n}{\mathop \sum }}\,\ln ({{t}_{i}}) \right)}^{2}} \\ & = 1400.9084-1301.4545 \\ & = 99.4539 \end{align}\,\! }[/math]
    [math]\displaystyle{ \begin{align} SE(\hat{\alpha })= & \frac{\sigma }{\sqrt{{{S}_{xx}}}} \\ = & \frac{0.08428}{9.9727} \\ = & 0.008452 \end{align}\,\! }[/math]
    [math]\displaystyle{ \begin{align} SE(\ln \hat{b})= & \sigma \cdot \sqrt{\frac{\underset{i=1}{\overset{n}{\mathop{\sum }}}\,{{(\ln {{T}_{i}})}^{2}}}{n\cdot {{S}_{xx}}}} \\ = & 0.065960 \end{align}\,\! }[/math]
    Thus, the 90% confidence bounds on parameter [math]\displaystyle{ \alpha \,\! }[/math] are:
    [math]\displaystyle{ C{{B}_{\alpha }}=\hat{\alpha }\pm {{t}_{n-2,\alpha /2}}SE(\hat{\alpha })\,\! }[/math]
    [math]\displaystyle{ \begin{align} {{\alpha }_{L}}= & 0.602050 \\ {{\alpha }_{U}}= & 0.624417 \end{align}\,\! }[/math]
    And 90% confidence bounds on parameter [math]\displaystyle{ b\,\! }[/math] are:
    [math]\displaystyle{ C{{B}_{b}}=\hat{b}{{e}^{\pm {{t}_{n-2,\alpha /2}}SE\left[ \ln (\hat{b}) \right]}}\,\! }[/math]
    [math]\displaystyle{ \begin{align} {{b}_{L}}= & 1.7831 \\ {{b}_{U}}= & 2.1231 \end{align}\,\! }[/math]
  2. The cumulative failure intensity is:
    [math]\displaystyle{ \begin{align} {{\lambda }_{c}}= & \frac{1}{1.9453}\cdot {{22000}^{-0.6133}} \\ = & 0.00111689 \end{align}\,\! }[/math]
    And the instantaneous failure intensity is equal to:
    [math]\displaystyle{ \begin{align} {{\lambda }_{i}}= & \frac{1}{1.9453}\cdot (1-0.6133)\cdot {{22000}^{-0.6133}} \\ = & 0.00043198 \end{align}\,\! }[/math]
    So, at the 90% confidence level and for [math]\displaystyle{ T=22,000\,\! }[/math] hours, the confidence bounds on cumulative failure intensity are:
    [math]\displaystyle{ \begin{align} {{[{{\lambda }_{c}}(t)]}_{L}}= & 0.00106780 \\ {{[{{\lambda }_{c}}(t)]}_{U}}= & 0.00116825 \end{align}\,\! }[/math]
    For the instantaneous failure intensity:
    [math]\displaystyle{ \begin{align} {{[{{\lambda }_{i}}(t)]}_{L}}= & 0.00041299 \\ {{[{{\lambda }_{c}}(t)]}_{U}}= & 0.00045184 \end{align}\,\! }[/math]
    The following figures show the graphs of the cumulative and instantaneous failure intensity. Both are plotted with confidence bounds.
    Rga4.7.png
    Rga4.8.png
  3. The cumulative MTBF is:
    [math]\displaystyle{ \begin{align} {{m}_{c}}(T)= & 1.9453\cdot {{22000}^{0.6133}} \\ = & 895.3395 \end{align}\,\! }[/math]
    And the instantaneous MTBF is:
    [math]\displaystyle{ \begin{align} {{m}_{i}}(T)= & \frac{1.9453}{1-0.6133}\cdot {{22000}^{0.6133}} \\ = & 2314.9369 \end{align}\,\! }[/math]
    So, at 90% confidence level and for [math]\displaystyle{ T=22,000\,\! }[/math] hours, the confidence bounds on the cumulative MTBF are:
    [math]\displaystyle{ \begin{align} {{m}_{c}}{{(t)}_{l}}= & 855.9815 \\ {{m}_{c}}{{(t)}_{u}}= & 936.5071 \end{align}\,\! }[/math]
    The confidence bounds for the instantaneous MTBF are:
    [math]\displaystyle{ \begin{align} {{m}_{i}}{{(t)}_{l}}= & 2213.1753 \\ {{m}_{i}}{{(t)}_{u}}= & 2421.3776 \end{align}\,\! }[/math]
    The figure below displays the cumulative MTBF.
    Rga4.9.png

    The next figure displays the instantaneous MTBF. Both are plotted with confidence bounds.

    Rga4.10.png

More Examples

Estimating the Time Required to Meet an MTBF Goal

A prototype of a system was tested with design changes incorporated during the test. A total of 12 failures occurred. The data set is given in the following table.

Developmental Test Data
Failure Number Cumulative Test Time(hours)
1 80
2 175
3 265
4 400
5 590
6 1100
7 1650
8 2010
9 2400
10 3380
11 5100
12 6400

Do the following:

  1. Estimate the Duane parameters.
  2. Plot the cumulative and instantaneous MTBF curves.
  3. How many cumulative test and development hours are required to meet an instantaneous MTBF goal of 500 hours?
  4. How many cumulative test and development hours are required to meet a cumulative MTBF goal of 500 hours?

Solution

  1. The next figure shows the data entered into RGA along with the estimated Duane parameters.
    Rga4.11.png
  2. The following figure shows the cumulative and instantaneous MTBF curves.
    Rga4.12.png
  3. The next figure shows the cumulative test and development hours needed for an instantaneous MTBF goal of 500 hours.
    Rga4.13.png
  4. The figure below shows the cumulative test and development hours needed for a cumulative MTBF goal of 500 hours.
    Rga4.14.png

Multiple Systems - Known Operating Times Example

Two identical systems were tested. Any design changes made to improve the reliability of these systems were incorporated into both systems when any system failed. A total of 29 failures occurred. The data set is given in the table below.

Do the following:

  1. Estimate the Duane parameters.
  2. Assume both units are tested for an additional 100 hours each. How many failures do you expect in that period?
  3. If testing/development were halted at this point, what would the reliability equation for this system be?
Developmental Test Data
Failure Number Failed Unit Test Time Unit 1(hours) Test Time Unit 2 (hours)
1 1 0.2 2.0
2 2 1.7 2.9
3 2 4.5 5.2
4 2 5.8 9.1
5 2 17.3 9.2
6 2 29.3 24.1
7 1 36.5 61.1
8 2 46.3 69.6
9 1 63.6 78.1
10 2 64.4 85.4
11 1 74.3 93.6
12 1 106.6 103
13 2 195.2 117
14 2 235.1 134.3
15 1 248.7 150.2
16 2 256.8 164.6
17 2 261.1 174.3
18 2 299.4 193.2
19 1 305.3 234.2
20 1 326.9 257.3
21 1 339.2 290.2
22 1 366.1 293.1
23 2 466.4 316.4
24 1 504 373.2
25 1 510 375.1
26 2 543.2 386.1
27 2 635.4 453.3
28 1 641.2 485.8
29 2 755.8 573.6

Solution

  1. The figure below shows the data entered into RGA along with the estimated Duane parameters.
    Rga4.15.png
  2. The current accumulated test time for both units is 1329.4 hours. If the process were to continue for an additional combined time of 200 hours, the expected cumulative number of failures at [math]\displaystyle{ T=1529.4\,\! }[/math] is 31.2695, as shown in the figure below. At T = 1329.4, the expected number of failures is 29.2004. Therefore, the expected number of failures that would be observed over the additional 200 hours is [math]\displaystyle{ 31.2695-29.2004=2.0691\approx 2\,\! }[/math].
    Rga4.16.png
  3. If testing/development were halted at this point, the system failure intensity would be equal to the instantaneous failure intensity at that time, or [math]\displaystyle{ \lambda =0.0107\,\! }[/math] failures/hour. See the following figure.
    Rga4.17.png

    An exponential distribution can be assumed since the value of the failure intensity at that instant in time is known. Therefore:

    [math]\displaystyle{ \begin{align} R(t)= & {{e}^{-\lambda t}} \\ = & {{e}^{-(0.0107)t}} \end{align}\,\! }[/math]

    Weibull++ can be utilized to provide a Reliability vs. Time plot which is shown below.

    Rga4.18.png

Using the Duane Model for Success/Failure Data

Given the sequential success/failure data in the table below, do the following:

  1. Estimate the Duane parameters.
  2. What is the instantaneous Reliability at the end of the test?
  3. How many additional test runs with a one-sided 90% confidence level are required to meet an instantaneous Reliability goal of 80%?
Sequential Data
Run Number Result
1 F
2 F
3 S
4 S
5 S
6 F
7 S
8 F
9 F
10 S
11 S
12 S
13 F
14 S
15 S
16 S
17 S
18 S
19 S
20 S

Solution

  1. The following figure shows the data set entered into RGA along with the estimated Duane parameters.
    Rga4.19.png
  2. The Reliability at the end of the test is equal to 78.22%. Note that this is the DRel that is shown in the control panel in the above figure.
  3. The figure below shows the number of test runs with both one-sided confidence bounds at 90% confidence level to achieve an instantaneous Reliability of 80%. Therefore, the number of additional test runs required with a 90% confidence level is equal to [math]\displaystyle{ 42.2481-20=22.2481\approx 23\,\! }[/math] test runs.
    Rga4.20.png