Crow-AMSAA (NHPP): Difference between revisions

From ReliaWiki
Jump to navigation Jump to search
(Replaced content with '{{template:RGA BOOK|5|Crow-AMSAA}} {{crow-amsaa(nhpp)}}')
Line 2: Line 2:




=Crow-AMSAA (NHPP)=
{{crow-amsaa(nhpp)}}
In Reliability Analysis for Complex, Repairable Systems (1974), Dr. Larry H. Crow noted that the Duane model could be stochastically represented as a Weibull process, allowing for statistical procedures to be used in the application of this model in reliability growth. This statistical extension became what is known as the Crow-AMSAA (NHPP) model. This method was first developed at the U.S. Army Materiel Systems Analysis Activity (AMSAA). It is frequently used on systems when usage is measured on a continuous scale. It can also be applied for the analysis of one shot items when there is high reliability and large number of trials.
Test programs are generally conducted on a phase by phase basis. The Crow-AMSAA model is designed for tracking the reliability within a test phase and not across test phases. A development testing program may consist of several separate test phases. If corrective actions are introduced during a particular test phase then this type of testing and the associated data are appropriate for analysis by the Crow-AMSAA model. The model analyzes the reliability growth progress within each test phase and can aid in determining the following:
<br>
 
• Reliability of the configuration currently on test
<br>
• Reliability of the configuration on test at the end of the test phase
<br>
• Expected reliability if the test time for the phase is extended
<br>
• Growth rate
<br>
• Confidence intervals
<br>
• Applicable goodness-of-fit tests
<br>
 
The reliability growth pattern for the Crow-AMSAA model is exactly the same pattern as for the Duane postulate (Chapter 4). That is, the cumulative number of failures is linear when plotted on ln-ln scale. Unlike the Duane postulate, the Crow-AMSAA model is statistically based. Under the Duane postulate, the failure rate is linear on ln-ln scale. However for the Crow-AMSAA model statistical structure, the failure intensity of the underlying non-homogeneous Poisson process (NHPP) is linear when plotted on ln-ln scale.
Let  <math>N(t)</math>  be the cumulative number of failures observed in cumulative test time  <math>t</math>  and let  <math>\rho (t)</math>  be the failure intensity for the Crow-AMSAA model. Under the NHPP model,  <math>\rho (t)\Delta t</math>  is approximately the probably of a failure occurring over the interval  <math>[t,t+\Delta t]</math>  for small  <math>\Delta t</math> . In addition, the expected number of failures experienced over the test interval  <math>[0,T]</math>  under the Crow-AMSAA model is given by:
 
<br>
::<math>E[N(T)]=\mathop{}_{0}^{T}\rho (t)dt</math>
 
<br>
The Crow-AMSAA model assumes that  <math>\rho (T)</math>  may be approximated by the Weibull failure rate function:
 
<br>
::<math>\rho (T)=\frac{\beta }{{{\eta }^{\beta }}}{{T}^{\beta -1}}</math>
 
<br>
Therefore, if  <math>\lambda =\tfrac{1}{{{\eta }^{\beta }}},</math>  the intensity function,  <math>\rho (T),</math>  or the instantaneous failure intensity,  <math>{{\lambda }_{i}}(T)</math> , is defined as:
 
<br>
::<math>{{\lambda }_{i}}(T)=\lambda \beta {{T}^{\beta -1}},\text{with }T>0,\text{ }\lambda >0\text{ and }\beta >0</math>
 
In the special case of exponential failure times there is no growth and the failure intensity,  <math>\rho (t)</math> , is equal to  <math>\lambda </math> . In this case, the expected number of failures is given by:
 
<br>
::<math>\begin{align}
  & E[N(T)]= & \mathop{}_{0}^{T}\rho (t)dt \\
& = & \lambda T 
\end{align}</math>
 
In order for the plot to be linear when plotted on ln-ln scale under the general reliability growth case, the following must hold true where the expected number of failures is equal to:
 
<br>
::<math>\begin{align}
  & E[N(T)]= & \mathop{}_{0}^{T}\rho (t)dt \\
& = & \lambda {{T}^{\beta }} 
\end{align}</math>
 
To put a statistical structure on the reliability growth process, consider again the special case of no growth. In this case the number of failures,  <math>N(T),</math>  experienced during the testing over  <math>[0,T]</math>  is random. The expected number of failures,  <math>N(T),</math>  is said to follow the homogeneous (constant) Poisson process with mean  <math>\lambda T</math>  and is given by:
 
<br>
::<math>\underset{}{\overset{}{\mathop{\Pr }}}\,[N(T)=n]=\frac{{{(\lambda T)}^{n}}{{e}^{-\lambda T}}}{n!};\text{ }n=0,1,2,\ldots </math>
 
The Crow-AMSAA generalizes this no growth case to allow for reliability growth due to corrective actions. This generalization keeps the Poisson distribution for the number of failures but allows for the expected number of failures,  <math>E[N(T)],</math>  to be linear when plotted on ln-ln scale. The Crow-AMSAA model lets  <math>E[N(T)]=\lambda {{T}^{\beta }}</math> . The probability that the number of failures,  <math>N(T),</math>  will be equal to  <math>n</math>  under growth is then given by the Poisson distribution:
 
<br>
::<math>\underset{}{\overset{}{\mathop{\Pr }}}\,[N(T)=n]=\frac{{{(\lambda {{T}^{\beta }})}^{n}}{{e}^{-\lambda {{T}^{\beta }}}}}{n!};\text{ }n=0,1,2,\ldots </math>
 
This is the general growth situation and the number of failures,  <math>N(T)</math> , follows a non-homogeneous Poisson process. The exponential, "no growth" homogeneous Poisson process is a special case of the non-homogeneous Crow-AMSAA model. This is reflected in the Crow-AMSAA model parameter where  <math>\beta =1</math> .
The cumulative failure rate,  <math>{{\lambda }_{c}}</math> , is:
 
<br>
::<math>{{\lambda }_{c}}=\lambda {{T}^{\beta -1}}</math>
 
The cumulative  <math>MTB{{F}_{c}}</math>  is:
 
<br>
::<math>MTB{{F}_{c}}=\frac{1}{\lambda }{{T}^{1-\beta }}</math>
 
As mentioned above, the local pattern for reliability growth within a test phase is the same as the growth pattern observed by Duane, discussed in Chapter 4. The Duane  <math>MTB{{F}_{c}}</math>  is equal to:
 
<br>
::<math>MTB{{F}_{{{c}_{DUANE}}}}=b{{T}^{\alpha }}</math>
 
And the Duane cumulative failure rate,  <math>{{\lambda }_{c}}</math> , is:
 
<br>
::<math>{{\lambda }_{{{c}_{DUANE}}}}=\frac{1}{b}{{T}^{-\alpha }}</math>
 
Thus a relationship between Crow-AMSAA parameters and Duane parameters can be developed, such that:
 
<br>
::<math>\begin{align}
  & {{b}_{DUANE}}= & \frac{1}{{{\lambda }_{AMSAA}}} \\
& {{\alpha }_{DUANE}}= & 1-{{\beta }_{AMSAA}} 
\end{align}</math>
 
 
Note that these relationships are not absolute. They change according to how the parameters (slopes, intercepts, etc.) are defined when the analysis of the data is performed. For the exponential case,  <math>\beta =1</math> , then  <math>{{\lambda }_{i}}(T)=\lambda </math> , a constant. For  <math>\beta >1</math> ,  <math>{{\lambda }_{i}}(T)</math>  is increasing. This indicates a deterioration in system reliability. For  <math>\beta <1</math> ,  <math>{{\lambda }_{i}}(T)</math>  is decreasing. This is indicative of reliability growth. Note that the model assumes a Poisson process with Weibull intensity function, not the Weibull distribution. Therefore, statistical procedures for the Weibull distribution do not apply for this model. The parameter  <math>\lambda </math>  is called a scale parameter because it depends upon the unit of measurement chosen for  <math>T</math> .  <math>\beta </math>  is the shape parameter that characterizes the shape of the graph of the intensity function.
The total number of failures,  <math>N(T)</math> , is a random variable with Poisson distribution. Therefore, the probability that exactly  <math>n</math>  failures occur by time  <math>T</math>  is:
 
<br>
::<math>P[N(T)=n]=\frac{{{[\theta (T)]}^{n}}{{e}^{-\theta (T)}}}{n!}</math>
 
The number of failures occurring in the interval from  <math>{{T}_{1}}</math>  to  <math>{{T}_{2}}</math>  is a random variable having a Poisson distribution with mean:
 
<br>
::<math>\theta ({{T}_{2}})-\theta ({{T}_{1}})=\lambda (T_{2}^{\beta }-T_{1}^{\beta })</math>
 
The number of failures in any interval is statistically independent of the number of failures in any interval that does not overlap the first interval. At time  <math>{{T}_{0}}</math> , the failure intensity is  <math>{{\lambda }_{i}}({{T}_{0}})=\lambda \beta T_{0}^{\beta -1}</math> . If improvements are not made to the system after time  <math>{{T}_{0}}</math> , it is assumed that failures would continue to occur at the constant rate  <math>{{\lambda }_{i}}({{T}_{0}})=\lambda \beta T_{0}^{\beta -1}</math> . Future failures would then follow an exponential distribution with mean  <math>m({{T}_{0}})=\tfrac{1}{\lambda \beta T_{0}^{\beta -1}}</math> . The instantaneous  <math>MTBF</math>  of the system at time  <math>T</math>  is:
 
<br>
::<math>m(T)=\frac{1}{\lambda \beta {{T}^{\beta -1}}}</math>
 
==Parameter Estimation==
===Maximum Likelihood Estimators===
The probability density function ( <math>pdf</math> ) of the  <math>{{i}^{th}}</math>  event given that the  <math>{{(i-1)}^{th}}</math>  event occurred at  <math>{{T}_{i-1}}</math>  is:
 
<br>
::<math>f({{T}_{i}}|{{T}_{i-1}})=\frac{\beta }{\eta }{{\left( \frac{{{T}_{i}}}{\eta } \right)}^{\beta -1}}\cdot {{e}^{-\tfrac{1}{{{\eta }^{\beta }}}\left( T_{i}^{\beta }-T_{i-1}^{\beta } \right)}}</math>
 
The likelihood function is:
 
<br>
::<math>L={{\lambda }^{n}}{{\beta }^{n}}{{e}^{-\lambda {{T}^{*\beta }}}}\underset{i=1}{\overset{n}{\mathop \prod }}\,T_{i}^{\beta -1}</math>
 
where  <math>{{T}^{*}}</math>  is the termination time and is given by:
 
<br>
::<math>{{T}^{*}}=\left\{ \begin{matrix}
  {{T}_{n}}\text{ if the test is failure terminated}  \\
  T>{{T}_{n}}\text{ if the test is time terminated}  \\
\end{matrix} \right\}</math>
 
Taking the natural log on both sides:
 
<br>
::<math>\Lambda =n\ln \lambda +n\ln \beta -\lambda {{T}^{*\beta }}+(\beta -1)\underset{i=1}{\overset{n}{\mathop \sum }}\,\ln {{T}_{i}}</math>
 
<br>
And differentiating with respect to  <math>\lambda </math>  yields:
 
<br>
::<math>\frac{\partial \Lambda }{\partial \lambda }=\frac{n}{\lambda }-{{T}^{*\beta }}</math>
 
<br>
Set equal to zero and solve for  <math>\lambda </math> :
 
<br>
::<math>\widehat{\lambda }=\frac{n}{{{T}^{*\beta }}}</math>
 
<br>
Now differentiate Eqn. (amsaa4) with respect to  <math>\beta </math> :
 
<br>
::<math>\frac{\partial \Lambda }{\partial \beta }=\frac{n}{\beta }-\lambda {{T}^{*\beta }}\ln {{T}^{*}}+\underset{i=1}{\overset{n}{\mathop \sum }}\,\ln {{T}_{i}}</math>
 
<br>
Set equal to zero and solve for  <math>\beta </math> :
 
<br>
::<math>\widehat{\beta }=\frac{n}{n\ln {{T}^{*}}-\underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln {{T}_{i}}}</math>
 
===Biasing and Unbiasing of Beta===
Eqn. (6) returns the biased estimate of  <math>\beta </math> . The unbiased estimate of  <math>\beta </math>  can be calculated by using the following relationships. For time terminated data (meaning that the test ends after a specified number of failures):
 
::<math>\bar{\beta }=\frac{N-1}{N}\hat{\beta }</math>
 
<br>
For failure terminated data (meaning that the test ends after a specified test time):
 
<br>
::<math>\bar{\beta }=\frac{N-2}{N}\hat{\beta }</math>
 
<br>
'''Example 1'''
<br>
Two prototypes of a system were tested simultaneously with design changes incorporated during the test. Table 5.1 presents the data collected over the entire test. Find the Crow-AMSAA parameters and the intensity function using maximum likelihood estimators.
<br>
<br>
<center>Table 5.1 - Developmental test data for two identical systems </center>
{|style= align="center" border="1"
!Failure Number
!Failed Unit
!Test Time Unit 1(hr)
!Test Time Unit 2(hr)
!Total Test Time(hr)
!<math>ln{(T)}</math>
|-
|1|| 1|| 1.0|| 1.7|| 2.7|| 0.99325
|-
|2|| 1|| 7.3|| 3.0|| 10.3|| 2.33214
|-
|3|| 2|| 8.7|| 3.8|| 12.5|| 2.52573
|-
|4|| 2|| 23.3|| 7.3|| 30.6|| 3.42100
|-
|5|| 2|| 46.4|| 10.6|| 57.0|| 4.04305
|-
|6|| 1|| 50.1|| 11.2|| 61.3|| 4.11578
|-
|7|| 1|| 57.8|| 22.2|| 80.0|| 4.38203
|-
|8|| 2|| 82.1|| 27.4|| 109.5|| 4.69592
|-
|9|| 2|| 86.6|| 38.4|| 125.0||4.82831
|-
|10|| 1|| 87.0|| 41.6|| 128.6|| 4.85671
|-
|11|| 2|| 98.7|| 45.1|| 143.8|| 4.96842
|-
|12|| 1|| 102.2|| 65.7|| 167.9|| 5.12337
|-
|13|| 1|| 139.2 ||90.0||229.2|| 5.43459
|-
|14|| 1|| 166.6|| 130.1|| 296.7|| 5.69272
|-
|15|| 2|| 180.8|| 139.8 ||320.6||5.77019
|-
|16|| 1|| 181.3|| 146.9|| 328.2|| 5.79362
|-
|17|| 2|| 207.9|| 158.3 ||366.2||5.90318
|-
|18|| 2|| 209.8|| 186.9|| 396.7|| 5.98318
|-
|19|| 2|| 226.9|| 194.2|| 421.1|| 6.04287
|-
|20|| 1|| 232.2|| 206.0|| 438.2|| 6.08268
|-
|21|| 2|| 267.5|| 233.7|| 501.2|| 6.21701
|-
|22|| 2|| 330.1|| 289.9|| 620.0|| 6.42972
|}
'''Solution'''
<br>
For the failure terminated test, using Eqn. (amsaa6):
 
::<math>\widehat{\beta }=\frac{22}{22\ln 620-\underset{i=1}{\overset{22}{\mathop{\sum }}}\,\ln {{T}_{i}}}</math>
 
:where:
 
<br>
::<math>\underset{i=1}{\overset{22}{\mathop \sum }}\,\ln {{T}_{i}}=105.6355</math>
 
<br>
:Then:
 
<br>
::<math>\widehat{\beta }=\frac{22}{22\ln 620-105.6355}=0.6142</math>
 
<br>
From Eqn. (amsaa5):
 
<br>
::<math>\widehat{\lambda }=\frac{22}{{{620}^{0.6142}}}=0.4239</math>
 
<br>
Therefore,  <math>{{\lambda }_{i}}(T)</math>  becomes:
 
<br>
::<math>\begin{align}
  & {{\widehat{\lambda }}_{i}}(T)= & 0.4239\cdot 0.6142\cdot {{620}^{-0.3858}} \\
& = & 0.0217906\frac{\text{failures}}{\text{hr}} 
\end{align}</math>
 
<br>
Figure 4fig81 shows the plot of the failure rate. If no further changes are made, the estimated MTBF is  <math>\tfrac{1}{0.0217906}</math>  or 46 hr.
<br>
<br>
[[Image:rga5.1.png|thumb|center|400px|Failure rate plot for Example 5-1 using Maximum Likelihood Estimation.]]
<br>
 
==Confidence Bounds==
This section presents the methods used in the RGA software to estimate the confidence bounds for the Crow-AMSAA model when applied to developmental testing data. RGA provides two methods to estimate the confidence bounds. The Fisher Matrix (FM) method, which is commonly employed in the reliability field, is based on the Fisher information matrix. The Crow Bounds (Crow) method has been developed by Dr. Crow.
===Bounds on  <math>\beta </math>===
====Fisher Matrix Bounds====
The parameter  <math>\beta </math>  must be positive, thus  <math>\ln \beta </math>  is treated as being normally distributed as well. 
 
<br>
::<math>\frac{\ln \hat{\beta }-\ln \beta }{\sqrt{Var(\ln \hat{\beta }})}\ \tilde{\ }\ N(0,1)</math>
 
<br>
The approximate confidence bounds are given as:
 
<br>
::<math>C{{B}_{\beta }}=\hat{\beta }{{e}^{\pm {{z}_{\alpha }}\sqrt{Var(\hat{\beta })}/\hat{\beta }}}</math>
 
<br>
<math>\alpha </math>  in  <math>{{z}_{\alpha }}</math>  is different ( <math>\alpha /2</math> ,  <math>\alpha </math> ) according to a 2-sided confidence interval or a 1-sided confidence interval, and variances can be calculated using the Fisher Matrix.
 
<br>
::<math>\left[ \begin{matrix}
  -\tfrac{{{\partial }^{2}}\Lambda }{\partial {{\lambda }^{2}}} & -\tfrac{{{\partial }^{2}}\Lambda }{\partial \lambda \partial \beta }  \\
  -\tfrac{{{\partial }^{2}}\Lambda }{\partial \lambda \partial \beta } & -\tfrac{{{\partial }^{2}}\Lambda }{\partial {{\beta }^{2}}}  \\
\end{matrix} \right]_{\beta =\widehat{\beta },\lambda =\widehat{\lambda }}^{-1}=\left[ \begin{matrix}
  Var(\widehat{\lambda }) & Cov(\widehat{\beta },\widehat{\lambda })  \\
  Cov(\widehat{\beta },\widehat{\lambda }) & Var(\widehat{\beta })  \\
\end{matrix} \right]</math>
<br>
::<math>\Lambda </math>  is the natural log-likelihood function:
<br>
::<math>\Lambda =N\ln \lambda +N\ln \beta -\lambda {{T}^{\beta }}+(\beta -1)\underset{i=1}{\overset{N}{\mathop \sum }}\,\ln {{T}_{i}}</math>
<br>
::<math>\frac{{{\partial }^{2}}\Lambda }{\partial {{\lambda }^{2}}}=-\frac{N}{{{\lambda }^{2}}}</math>
<br>
:and:
<br>
::<math>\frac{{{\partial }^{2}}\Lambda }{\partial {{\beta }^{2}}}=-\frac{N}{{{\beta }^{2}}}-\lambda {{T}^{\beta }}{{(\ln T)}^{2}}</math>
<br>
:also:
<br>
::<math>\frac{{{\partial }^{2}}\Lambda }{\partial \lambda \partial \beta }=-{{T}^{\beta }}\ln T</math>
 
====Crow Bounds====
'''Time Terminated Data'''
 
For the 2-sided  <math>(1-\alpha )</math> 100-percent confidence interval on  <math>\beta </math> , calculate:
 
::<math>\begin{align}
  & {{D}_{L}}= & \frac{\chi _{\tfrac{\alpha }{2},2N}^{2}}{2(N-1)} \\
& {{D}_{U}}= & \frac{\chi _{1-\tfrac{\alpha }{2},2N}^{2}}{2(N-1)} 
\end{align}</math>
 
The fractiles can be found in the tables of the  <math>{{\chi }^{2}}</math>  distribution. Thus the confidence bounds on  <math>\beta </math>  are:
 
::<math>\begin{align}
  & {{\beta }_{L}}= & {{D}_{L}}\cdot \hat{\beta } \\
& {{\beta }_{U}}= & {{D}_{U}}\cdot \hat{\beta } 
\end{align}</math>
 
<br>
'''Failure Terminated Data'''
<br>
For the 2-sided  <math>(1-\alpha )</math> 100-percent confidence interval on  <math>\beta </math> , calculate:
 
::<math>\begin{align}
  & {{D}_{L}}= & \frac{N\cdot \chi _{\tfrac{\alpha }{2},2(N-1)}^{2}}{2(N-1)(N-2)} \\
& {{D}_{U}}= & \frac{N\cdot \chi _{1-\tfrac{\alpha }{2},2(N-1)}^{2}}{2(N-1)(N-2)} 
\end{align}</math>
 
Thus the confidence bounds on  <math>\beta </math>  are:
 
::<math>\begin{align}
  & {{\beta }_{L}}= & {{D}_{L}}\cdot \hat{\beta } \\
& {{\beta }_{U}}= & {{D}_{U}}\cdot \hat{\beta } 
\end{align}</math>
 
===Bounds on  <math>\lambda </math>===
====Fisher Matrix Bounds====
The parameter  <math>\lambda </math>  must be positive, thus  <math>\ln \lambda </math>  is treated as being normally distributed as well. These bounds are based on:
<br>
::<math>\frac{\ln \hat{\lambda }-\ln \lambda }{\sqrt{Var(\ln \hat{\lambda }})}\ \tilde{\ }\ N(0,1)</math>
<br>
The approximate confidence bounds on  <math>\lambda </math>  are given as:
<br>
::<math>C{{B}_{\lambda }}=\hat{\lambda }{{e}^{\pm {{z}_{\alpha }}\sqrt{Var(\hat{\lambda })}/\hat{\lambda }}}</math>
<br>
:where:
<br>
::<math>\hat{\lambda }=\frac{n}{{{T}^{*\hat{\beta }}}}</math>
<br>
The variance calculation is the same as Eqn. (variance1).
 
====Crow Bounds====
'''Time Terminated Data'''
<br>
For the 2-sided  <math>(1-\alpha )</math> 100-percent confidence interval, the confidence bounds on  <math>\lambda </math>  are:
 
::<math>\begin{align}
  & {{\lambda }_{L}}= & \frac{\chi _{\tfrac{\alpha }{2},2N}^{2}}{2{{T}^{{\hat{\beta }}}}} \\
& {{\lambda }_{U}}= & \frac{\chi _{1-\tfrac{\alpha }{2},2N+2}^{2}}{2{{T}^{{\hat{\beta }}}}} 
\end{align}</math>
 
The fractiles can be found in the tables of the  <math>{{\chi }^{2}}</math>  distribution.
<br>
<br>
'''Failure Terminated Data'''
<br>
For the 2-sided  <math>(1-\alpha )</math> 100-percent confidence interval, the confidence bounds on  <math>\lambda </math>  are:
 
::<math>\begin{align}
  & {{\lambda }_{L}}= & \frac{\chi _{\tfrac{\alpha }{2},2N}^{2}}{2{{T}^{{\hat{\beta }}}}} \\
& {{\lambda }_{U}}= & \frac{\chi _{1-\tfrac{\alpha }{2},2N}^{2}}{2{{T}^{{\hat{\beta }}}}} 
\end{align}</math>
 
===Bounds on Growth Rate===
Since the growth rate is equal to  <math>1-\beta </math> , the confidence bounds for both the Fisher Matrix and Crow methods are:
<br>
::<math>G\text{row}th Rate_L=1-\beta_U</math>
::<math>G\text{row}th Rate_U=1-\beta_L</math>
 
For the Fisher Matrix confidence bounds,  <math>{{\beta }_{L}}</math>  and  <math>{{\beta }_{U}}</math>  are obtained from Eqn. (amsaac1). For the Crow bounds,  <math>{{\beta }_{L}}</math>  and  <math>{{\beta }_{U}}</math>  are obtained from Eqns. (amsaac2) and (amsaac22) depending on whether the analysis is for time terminated data or failure terminated data.
 
===Bounds on Cumulative MTBF===
====Fisher Matrix Bounds====
The cumulative MTBF,  <math>{{m}_{c}}(t)</math> , must be positive, thus  <math>\ln {{m}_{c}}(t)</math>  is treated as being normally distributed as well.
 
::<math>\frac{\ln {{{\hat{m}}}_{c}}(t)-\ln {{m}_{c}}(t)}{\sqrt{Var(\ln {{{\hat{m}}}_{c}}(t)})}\ \tilde{\ }\ N(0,1)</math>
 
The approximate confidence bounds on the cumulative MTBF are then estimated from:
 
::<math>CB={{\hat{m}}_{c}}(t){{e}^{\pm {{z}_{\alpha }}\sqrt{Var({{{\hat{m}}}_{c}}(t))}/{{{\hat{m}}}_{c}}(t)}}</math>
<br>
:where:
<br>
::<math>{{\hat{m}}_{c}}(t)=\frac{1}{{\hat{\lambda }}}{{t}^{1-\hat{\beta }}}</math>
 
::<math>\begin{align}
  & Var({{{\hat{m}}}_{c}}(t))= & {{\left( \frac{\partial {{m}_{c}}(t)}{\partial \beta } \right)}^{2}}Var(\hat{\beta })+{{\left( \frac{\partial {{m}_{c}}(t)}{\partial \lambda } \right)}^{2}}Var(\hat{\lambda }) \\
&  & +2\left( \frac{\partial {{m}_{c}}(t)}{\partial \beta } \right)\left( \frac{\partial {{m}_{c}}(t)}{\partial \lambda } \right)cov(\hat{\beta },\hat{\lambda })\, 
\end{align}</math>
<br>
The variance calculation is the same as Eqn. (variance1) and:
 
::<math>\begin{align}
  & \frac{\partial {{m}_{c}}(t)}{\partial \beta }= & -\frac{1}{{\hat{\lambda }}}{{t}^{1-\hat{\beta }}}\ln t \\
& \frac{\partial {{m}_{c}}(t)}{\partial \lambda }= & -\frac{1}{{{{\hat{\lambda }}}^{2}}}{{t}^{1-\hat{\beta }}} 
\end{align}</math>
 
====Crow Bounds====
To calculate the Crow confidence bounds on cumulative MTBF, first calculate the Crow cumulative failure intensity confidence bounds:
 
::<math>C{{(t)}_{L}}=\frac{\chi _{\tfrac{\alpha }{2},2N}^{2}}{2\cdot t}</math>
 
::<math>C{{(t)}_{U}}=\frac{\chi _{1-\tfrac{\alpha }{2},2N+2}^{2}}{2\cdot t}</math>
 
:Then:
 
::<math>\begin{align}
  & {{[MTB{{F}_{c}}]}_{L}}= & \frac{1}{C{{(t)}_{U}}} \\
& {{[MTB{{F}_{c}}]}_{U}}= & \frac{1}{C{{(t)}_{L}}} 
\end{align}</math>
 
===Bounds on Instantaneous MTBF===
====Fisher Matrix Bounds====
The instantaneous MTBF,  <math>{{m}_{i}}(t)</math> , must be positive, thus  <math>\ln {{m}_{i}}(t)</math>  is treated as being normally distributed as well.
 
::<math>\frac{\ln {{{\hat{m}}}_{i}}(t)-\ln {{m}_{i}}(t)}{\sqrt{Var(\ln {{{\hat{m}}}_{i}}(t)})}\ \tilde{\ }\ N(0,1)</math>
 
The approximate confidence bounds on the instantaneous MTBF are then estimated from:
 
::<math>CB={{\hat{m}}_{i}}(t){{e}^{\pm {{z}_{\alpha }}\sqrt{Var({{{\hat{m}}}_{i}}(t))}/{{{\hat{m}}}_{i}}(t)}}</math>
 
<br>
:where:
 
<br>
::<math>{{\hat{m}}_{i}}(t)=\frac{1}{\lambda \beta {{t}^{\beta -1}}}</math>
 
::<math>\begin{align}
  & Var({{{\hat{m}}}_{i}}(t))= & {{\left( \frac{\partial {{m}_{i}}(t)}{\partial \beta } \right)}^{2}}Var(\hat{\beta })+{{\left( \frac{\partial {{m}_{i}}(t)}{\partial \lambda } \right)}^{2}}Var(\hat{\lambda }) \\
&  & +2\left( \frac{\partial {{m}_{i}}(t)}{\partial \beta } \right)\left( \frac{\partial {{m}_{i}}(t)}{\partial \lambda } \right)cov(\hat{\beta },\hat{\lambda }). 
\end{align}</math>
 
The variance calculation is the same as Eqn. (variance1) and:
 
::<math>\begin{align}
  & \frac{\partial {{m}_{i}}(t)}{\partial \beta }= & -\frac{1}{\hat{\lambda }{{{\hat{\beta }}}^{2}}}{{t}^{1-\hat{\beta }}}-\frac{1}{\hat{\lambda }\hat{\beta }}{{t}^{1-\hat{\beta }}}\ln t \\
& \frac{\partial {{m}_{i}}(t)}{\partial \lambda }= & -\frac{1}{{{{\hat{\lambda }}}^{2}}\hat{\beta }}{{t}^{1-\hat{\beta }}} 
\end{align}</math>
 
====Crow Bounds====
 
'''Failure Terminated Data'''
<br>
Consider the following equation:
 
::<math>G(\mu |n)=\mathop{}_{0}^{\infty }\frac{{{e}^{-x}}{{x}^{n-2}}}{(n-2)!}\underset{i=0}{\overset{n-1}{\mathop \sum }}\,\frac{1}{i!}{{\left( \frac{\mu }{x} \right)}^{i}}\exp (-\frac{\mu }{x})\,dx</math>
 
Find the values  <math>{{p}_{1}}</math>  and  <math>{{p}_{2}}</math>  by finding the solution  <math>c</math>  to  <math>G({{n}^{2}}/c|n)=\xi </math>  for  <math>\xi =\tfrac{\alpha }{2}</math>  and  <math>\xi =1-\tfrac{\alpha }{2}</math> , respectively. If using the biased parameters,  <math>\hat{\beta }</math>  and  <math>\hat{\lambda }</math> , then the upper and lower confidence bounds are:
 
::<math>\begin{align}
  & {{[MTB{{F}_{i}}]}_{L}}= & MTB{{F}_{i}}\cdot {{p}_{1}} \\
& {{[MTB{{F}_{i}}]}_{U}}= & MTB{{F}_{i}}\cdot {{p}_{2}} 
\end{align}</math>
 
where  <math>MTB{{F}_{i}}=\tfrac{1}{\hat{\lambda }\hat{\beta }{{t}^{\hat{\beta }-1}}}</math> . If using the unbiased parameters,  <math>\bar{\beta }</math>  and  <math>\bar{\lambda }</math> , then the upper and lower confidence bounds are:
 
::<math>\begin{align}
  & {{[MTB{{F}_{i}}]}_{L}}= & MTB{{F}_{i}}\cdot \left( \frac{N-2}{N} \right)\cdot {{p}_{1}} \\
& {{[MTB{{F}_{i}}]}_{U}}= & MTB{{F}_{i}}\cdot \left( \frac{N-2}{N} \right)\cdot {{p}_{2}} 
\end{align}</math>
 
where  <math>MTB{{F}_{i}}=\tfrac{1}{\hat{\lambda }\hat{\beta }{{t}^{\hat{\beta }-1}}}</math> .
<br>
<br>
'''Time Terminated Data'''
<br>
Consider the following equation where  <math>{{I}_{1}}(.)</math>  is the modified Bessel function of order one:
 
::<math>H(x|k)=\underset{j=1}{\overset{k}{\mathop \sum }}\,\frac{{{x}^{2j-1}}}{{{2}^{2j-1}}(j-1)!j!{{I}_{1}}(x)}</math>
 
Find the values  <math>{{\Pi }_{1}}</math>  and  <math>{{\Pi }_{2}}</math>  by finding the solution  <math>x</math>  to  <math>H(x|k)=\tfrac{\alpha }{2}</math>  and  <math>H(x|k)=1-\tfrac{\alpha }{2}</math>  in the cases corresponding to the lower and upper bounds, respectively. Calculate  <math>\Pi =\tfrac{4{{n}^{2}}}{{{x}^{2}}}</math>  for each case. If using the biased parameters,  <math>\hat{\beta }</math>  and  <math>\hat{\lambda }</math> , then the upper and lower confidence bounds are:
 
::<math>\begin{align}
  & {{[MTB{{F}_{i}}]}_{L}}= & MTB{{F}_{i}}\cdot {{\Pi }_{1}} \\
& {{[MTB{{F}_{i}}]}_{U}}= & MTB{{F}_{i}}\cdot {{\Pi }_{2}} 
\end{align}</math>
 
where  <math>MTB{{F}_{i}}=\tfrac{1}{\hat{\lambda }\hat{\beta }{{t}^{\hat{\beta }-1}}}</math> . If using the unbiased parameters,  <math>\bar{\beta }</math>  and  <math>\bar{\lambda }</math> , then the upper and lower confidence bounds are:
 
::<math>\begin{align}
  & {{[MTB{{F}_{i}}]}_{L}}= & MTB{{F}_{i}}\cdot \left( \frac{N-1}{N} \right)\cdot {{\Pi }_{1}} \\
& {{[MTB{{F}_{i}}]}_{U}}= & MTB{{F}_{i}}\cdot \left( \frac{N-1}{N} \right)\cdot {{\Pi }_{2}} 
\end{align}</math>
 
where  <math>MTB{{F}_{i}}=\tfrac{1}{\hat{\lambda }\hat{\beta }{{t}^{\hat{\beta }-1}}}</math> .
 
===Bounds on Cumulative Failure Intensity===
====Fisher Matrix Bounds====
The cumulative failure intensity,  <math>{{\lambda }_{c}}(t)</math> , must be positive, thus  <math>\ln {{\lambda }_{c}}(t)</math>  is treated as being normally distributed.
 
::<math>\frac{\ln {{{\hat{\lambda }}}_{c}}(t)-\ln {{\lambda }_{c}}(t)}{\sqrt{Var(\ln {{{\hat{\lambda }}}_{c}}(t)})}\ \tilde{\ }\ N(0,1)</math>
 
The approximate confidence bounds on the cumulative failure intensity are then estimated from:
 
::<math>CB={{\hat{\lambda }}_{c}}(t){{e}^{\pm {{z}_{\alpha }}\sqrt{Var({{{\hat{\lambda }}}_{c}}(t))}/{{{\hat{\lambda }}}_{c}}(t)}}</math>
 
:where:
 
::<math>{{\hat{\lambda }}_{c}}(t)=\hat{\lambda }{{t}^{\hat{\beta }-1}}</math>
 
:and:
 
::<math>\begin{align}
  & Var({{{\hat{\lambda }}}_{c}}(t))= & {{\left( \frac{\partial {{\lambda }_{c}}(t)}{\partial \beta } \right)}^{2}}Var(\hat{\beta })+{{\left( \frac{\partial {{\lambda }_{c}}(t)}{\partial \lambda } \right)}^{2}}Var(\hat{\lambda }) \\
&  & +2\left( \frac{\partial {{\lambda }_{c}}(t)}{\partial \beta } \right)\left( \frac{\partial {{\lambda }_{c}}(t)}{\partial \lambda } \right)cov(\hat{\beta },\,\,\,\hat{\lambda }) 
\end{align}</math>
 
The variance calculation is the same as Eqn. (variance1) and:
 
::<math>\begin{align}
  & \frac{\partial {{\lambda }_{c}}(t)}{\partial \beta }= & \hat{\lambda }{{t}^{\hat{\beta }-1}}\ln t \\
& \frac{\partial {{\lambda }_{c}}(t)}{\partial \lambda }= & {{t}^{\hat{\beta }-1}} 
\end{align}</math>
 
 
====Crow Bounds====
The Crow cumulative failure intensity confidence bounds are given as:
 
::<math>\begin{align}
  & C{{(t)}_{L}}= & \frac{\chi _{\tfrac{\alpha }{2},2N}^{2}}{2\cdot t} \\
& C{{(t)}_{U}}= & \frac{\chi _{1-\tfrac{\alpha }{2},2N+2}^{2}}{2\cdot t} 
\end{align}</math>
 
===Bounds on Instantaneous Failure Intensity===
====Fisher Matrix Bounds====
The instantaneous failure intensity,  <math>{{\lambda }_{i}}(t)</math> , must be positive, thus  <math>\ln {{\lambda }_{i}}(t)</math>  is treated as being normally distributed.
 
::<math>\frac{\ln {{{\hat{\lambda }}}_{i}}(t)-\ln {{\lambda }_{i}}(t)}{\sqrt{Var(\ln {{{\hat{\lambda }}}_{i}}(t)})}\text{ }\tilde{\ }\text{ }N(0,1)</math>
 
The approximate confidence bounds on the instantaneous failure intensity are then estimated from:
 
::<math>CB={{\hat{\lambda }}_{i}}(t){{e}^{\pm {{z}_{\alpha }}\sqrt{Var({{{\hat{\lambda }}}_{i}}(t))}/{{{\hat{\lambda }}}_{i}}(t)}}</math>
 
:where
 
::<math>{{\lambda }_{i}}(t)=\lambda \beta {{t}^{\beta -1}}</math> 
 
::<math>\begin{align}
  & Var({{{\hat{\lambda }}}_{i}}(t))= & {{\left( \frac{\partial {{\lambda }_{i}}(t)}{\partial \beta } \right)}^{2}}Var(\hat{\beta })+{{\left( \frac{\partial {{\lambda }_{i}}(t)}{\partial \lambda } \right)}^{2}}Var(\hat{\lambda }) \\
&  & +2\left( \frac{\partial {{\lambda }_{i}}(t)}{\partial \beta } \right)\left( \frac{\partial {{\lambda }_{i}}(t)}{\partial \lambda } \right)cov(\hat{\beta },\,\,\,\hat{\lambda }) 
\end{align}</math>
 
The variance calculation is the same as Eqn. (variance1) and:
 
<br>
::<math>\begin{align}
  & \frac{\partial {{\lambda }_{i}}(t)}{\partial \beta }= & \hat{\lambda }{{t}^{\hat{\beta }-1}}+\hat{\lambda }\hat{\beta }{{t}^{\hat{\beta }-1}}\ln t \\
& \frac{\partial {{\lambda }_{i}}(t)}{\partial \lambda }= & \hat{\beta }{{t}^{\hat{\beta }-1}} 
\end{align}</math>
 
====Crow Bounds====
The Crow instantaneous failure intensity confidence bounds are given as:
 
::<math>\begin{align}
  & {{\lambda }_{i}}{{(t)}_{L}}= & \frac{1}{{{[MTB{{F}_{i}}]}_{U}}} \\
& {{\lambda }_{i}}{{(t)}_{U}}= & \frac{1}{{{[MTB{{F}_{i}}]}_{L}}} 
\end{align}</math>
 
===Bounds on Time Given Cumulative Failure Intensity===
====Fisher Matrix Bounds====
The time,  <math>T</math> , must be positive, thus  <math>\ln T</math>  is treated as being normally distributed.
 
::<math>\frac{\ln \hat{T}-\ln T}{\sqrt{Var(\ln \hat{T}})}\ \tilde{\ }\ N(0,1)</math>
<br>
Confidence bounds on the time are given by:
<br>
::<math>CB=\hat{T}{{e}^{\pm {{z}_{\alpha }}\sqrt{Var(\hat{T})}/\hat{T}}}</math>
<br>
:where:
<br>
::<math>\begin{align}
  & Var(\hat{T})= & {{\left( \frac{\partial T}{\partial \beta } \right)}^{2}}Var(\hat{\beta })+{{\left( \frac{\partial T}{\partial \lambda } \right)}^{2}}Var(\hat{\lambda }) \\
&  & +2\left( \frac{\partial T}{\partial \beta } \right)\left( \frac{\partial T}{\partial \lambda } \right)cov(\hat{\beta },\,\,\,\hat{\lambda }) 
\end{align}</math>
<br>
The variance calculation is the same as Eqn. (variance1) and:
::<math>\begin{align}
  & \frac{\partial T}{\partial \beta }= & \frac{-{{\left( \tfrac{{{\lambda }_{c}}(T)}{\lambda } \right)}^{1/(\beta -1)}}\ln \left( \tfrac{{{\lambda }_{c}}(T)}{\lambda } \right)}{{{(1-\beta )}^{2}}} \\
& \frac{\partial T}{\partial \lambda }= & {{\left( \frac{{{\lambda }_{c}}(T)}{\lambda } \right)}^{1/(\beta -1)}}\frac{1}{\lambda (1-\beta )} 
\end{align}</math>
 
====Crow Bounds====
:Step 1: Calculate:
 
::<math>\hat{T}={{\left( \frac{{{\lambda }_{c}}(T)}{{\hat{\lambda }}} \right)}^{\tfrac{1}{\beta -1}}}</math>
 
:Step 2: Estimate the number of failures:
 
::<math>N(\hat{T})=\hat{\lambda }{{\hat{T}}^{{\hat{\beta }}}}</math>
 
:Step 3: Obtain the confidence bounds on time given the cumulative failure intensity by solving for  <math>{{t}_{l}}</math>  and  <math>{{t}_{u}}</math>  in the following equations:
 
::<math>\begin{align}
  & {{t}_{l}}= & \frac{\chi _{\tfrac{\alpha }{2},2N}^{2}}{2\cdot {{\lambda }_{c}}(T)} \\
& {{t}_{u}}= & \frac{\chi _{1-\tfrac{\alpha }{2},2N+2}^{2}}{2\cdot {{\lambda }_{c}}(T)} 
\end{align}</math>
 
===Bounds on Time Given Cumulative MTBF===
====Fisher Matrix Bounds====
The time,  <math>T</math> , must be positive, thus  <math>\ln T</math>  is treated as being normally distributed.
::<math>\frac{\ln \hat{T}-\ln T}{\sqrt{Var(\ln \hat{T}})}\ \tilde{\ }\ N(0,1)</math>
<br>
Confidence bounds on the time are given by:
<br>
::<math>CB=\hat{T}{{e}^{\pm {{z}_{\alpha }}\sqrt{Var(\hat{T})}/\hat{T}}}</math>
:where:
::<math>\begin{align}
  & Var(\hat{T})= & {{\left( \frac{\partial T}{\partial \beta } \right)}^{2}}Var(\hat{\beta })+{{\left( \frac{\partial T}{\partial \lambda } \right)}^{2}}Var(\hat{\lambda }) \\
&  & +2\left( \frac{\partial T}{\partial \beta } \right)\left( \frac{\partial T}{\partial \lambda } \right)cov(\hat{\beta },\,\,\,\hat{\lambda }) 
\end{align}</math>
<br>
The variance calculation is the same as Eqn. (variance1) and:
<br>
::<math>\hat{T}={{(\lambda \cdot {{m}_{c}})}^{1/(1-\beta )}}</math>
 
::<math>\begin{align}
  & \frac{\partial T}{\partial \beta }= & \frac{{{(\lambda \cdot \,{{m}_{c}})}^{1/(1-\beta )}}\ln (\lambda \cdot \text{ }{{m}_{c}})}{{{(1-\beta )}^{2}}} \\
& \frac{\partial T}{\partial \lambda }= & \frac{{{(\lambda \text{ }\cdot \text{ }{{m}_{c}})}^{1/(1-\beta )}}}{\lambda (1-\beta )} 
\end{align}</math>
 
====Crow Bounds====
:Step 1: Calculate  <math>{{\lambda }_{c}}(T)=\tfrac{1}{MTB{{F}_{c}}}</math> .
:Step 2: Use the equations from 5.2.8.2 to calculate the bounds on time given the cumulative failure intensity.
 
===Bounds on Time Given Instantaneous MTBF===
====Fisher Matrix Bounds====
The time,  <math>T</math> , must be positive, thus  <math>\ln T</math>  is treated as being normally distributed.
 
::<math>\frac{\ln \hat{T}-\ln T}{\sqrt{Var(\ln \hat{T}})}\ \tilde{\ }\ N(0,1)</math>
 
<br>
Confidence bounds on the time are given by:
 
::<math>CB=\hat{T}{{e}^{\pm {{z}_{\alpha }}\sqrt{Var(\hat{T})}/\hat{T}}}</math>
 
<br>
:where:
 
::<math>\begin{align}
  & Var(\hat{T})= & {{\left( \frac{\partial T}{\partial \beta } \right)}^{2}}Var(\hat{\beta })+{{\left( \frac{\partial T}{\partial \lambda } \right)}^{2}}Var(\hat{\lambda }) \\
&  & +2\left( \frac{\partial T}{\partial \beta } \right)\left( \frac{\partial T}{\partial \lambda } \right)cov(\hat{\beta },\,\,\,\hat{\lambda }) 
\end{align}</math>
 
<br>
The variance calculation is the same as Eqn. (variance1) and:
 
::<math>\hat{T}={{(\lambda \beta \cdot MTB{{F}_{i}})}^{1/(1-\beta )}}</math>
 
::<math>\begin{align}
  & \frac{\partial T}{\partial \beta }= & {{\left( \lambda \beta \cdot MTB{{F}_{i}} \right)}^{1/(1-\beta )}}\left[ \frac{1}{{{(1-\beta )}^{2}}}\ln (\lambda \beta \cdot MTB{{F}_{i}})+\frac{1}{\beta (1-\beta )} \right] \\
& \frac{\partial T}{\partial \lambda }= & \frac{{{(\lambda \beta \cdot MTB{{F}_{i}})}^{1/(1-\beta )}}}{\lambda (1-\beta )} 
\end{align}</math>
 
====Crow Bounds====
:Step 1: Calculate the confidence bounds on the instantaneous MTBF as presented in Section 5.5.2.
:Step 2: Calculate the bounds on time as follows.
 
====Failure Terminated Data====
 
::<math>\hat{T}={{(\frac{\lambda \beta \cdot MTB{{F}_{i}}}{c})}^{1/(1-\beta )}}</math>
 
So the lower an upper bounds on time are:
 
::<math>{{\hat{T}}_{L}}={{(\frac{\lambda \beta \cdot MTB{{F}_{i}}}{{{c}_{1}}})}^{1/(1-\beta )}}</math>
 
::<math>{{\hat{T}}_{U}}={{(\frac{\lambda \beta \cdot MTB{{F}_{i}}}{{{c}_{2}}})}^{1/(1-\beta )}}</math>
 
'''Time Terminated Data'''
 
::<math>\hat{T}={{(\frac{\lambda \beta \cdot MTB{{F}_{i}}}{\Pi })}^{1/(1-\beta )}}</math>
<br>
So the lower and upper bounds on time are:
 
::<math>{{\hat{T}}_{L}}={{(\frac{\lambda \beta \cdot MTB{{F}_{i}}}{{{\Pi }_{1}}})}^{1/(1-\beta )}}</math>
 
::<math>{{\hat{T}}_{U}}={{(\frac{\lambda \beta \cdot MTB{{F}_{i}}}{{{\Pi }_{2}}})}^{1/(1-\beta )}}</math>
 
===Bounds on Time Given Instantaneous Failure Intensity===
====Fisher Matrix Bounds====
The time,  <math>T</math> , must be positive, thus  <math>\ln T</math>  is treated as being normally distributed.
 
::<math>\frac{\ln \hat{T}-\ln T}{\sqrt{Var(\ln \hat{T}})}\ \tilde{\ }\ N(0,1)</math>
 
<br>
Confidence bounds on the time are given by:
 
::<math>CB=\hat{T}{{e}^{\pm {{z}_{\alpha }}\sqrt{Var(\hat{T})}/\hat{T}}}</math>
 
<br>
:where:
 
::<math>\begin{align}
  & Var(\hat{T})= & {{\left( \frac{\partial T}{\partial \beta } \right)}^{2}}Var(\hat{\beta })+{{\left( \frac{\partial T}{\partial \lambda } \right)}^{2}}Var(\hat{\lambda }) \\
&  & +2\left( \frac{\partial T}{\partial \beta } \right)\left( \frac{\partial T}{\partial \lambda } \right)cov(\hat{\beta },\,\,\,\hat{\lambda }) 
\end{align}</math>
 
<br>
The variance calculation is the same as Eqn. (variance1) and: 
 
::<math>\hat{T}={{\left( \frac{{{\lambda }_{i}}(T)}{\lambda \beta } \right)}^{1/(\beta -1)}}</math>
<br>
::<math>\begin{align}
  & \frac{\partial T}{\partial \beta }= & {{\left( \frac{{{\lambda }_{i}}(T)}{\lambda \beta } \right)}^{1/(\beta -1)}}\left[ -\frac{\ln (\tfrac{{{\lambda }_{i}}(T)}{\lambda \beta })}{{{(\beta -1)}^{2}}}+\frac{1}{\beta (1-\beta )} \right] \\
& \frac{\partial T}{\partial \lambda }= & {{\left( \frac{{{\lambda }_{i}}(T)}{\lambda \beta } \right)}^{1/(\beta -1)}}\frac{1}{\lambda (1-\beta )} 
\end{align}</math>
 
====Crow Bounds====
:Step 1: Calculate  <math>MTB{{F}_{i}}=\tfrac{1}{{{\lambda }_{i}}(T)}</math> .
:Step 2: Use the equations from 5.2.10.2 to calculate the bounds on time given the instantaneous failure intensity.
 
===Bounds on Cumulative Number of Failures===
====Fisher Matrix Bounds====
The cumulative number of failures,  <math>N(t)</math> , must be positive, thus  <math>\ln N(t)</math>  is treated as being normally distributed. 
 
::<math>\frac{\ln \hat{N}(t)-\ln N(t)}{\sqrt{Var(\ln \hat{N}(t)})}\ \tilde{\ }\ N(0,1)</math>
 
::<math>N(t)=\hat{N}(t){{e}^{\pm {{z}_{\alpha }}\sqrt{Var(\hat{N}(t))}/\hat{N}(t)}}</math>
 
<br>
:where:
 
::<math>\hat{N}(t)=\hat{\lambda }{{t}^{{\hat{\beta }}}}</math>
 
::<math>\begin{align}
  & Var(\hat{N}(t))= & {{\left( \frac{\partial \hat{N}(t)}{\partial \beta } \right)}^{2}}Var(\hat{\beta })+{{\left( \frac{\partial \hat{N}(t)}{\partial \lambda } \right)}^{2}}Var(\hat{\lambda }) \\
&  & +2\left( \frac{\partial \hat{N}(t)}{\partial \beta } \right)\left( \frac{\partial \hat{N}(t)}{\partial \lambda } \right)cov(\hat{\beta },\hat{\lambda }) 
\end{align}</math>
 
The variance calculation is the same as Eqn. (variance1) and:
 
::<math>\begin{align}
  & \frac{\partial \hat{N}(t)}{\partial \beta }= & \hat{\lambda }{{t}^{{\hat{\beta }}}}\ln t \\
& \frac{\partial \hat{N}(t)}{\partial \lambda }= & {{t}^{{\hat{\beta }}}} 
\end{align}</math>
 
====Crow Bounds====
<br>
The Crow cumulative number of failure confidence bounds are:
 
::<math>\begin{align}
  & {{N}_{L}}(T)= & \frac{T}{{\hat{\beta }}}{{\lambda }_{i}}{{(T)}_{L}} \\
& {{N}_{U}}(T)= & \frac{T}{{\hat{\beta }}}{{\lambda }_{i}}{{(T)}_{U}} 
\end{align}</math>
 
<br>
where  <math>{{\lambda }_{i}}{{(T)}_{L}}</math>  and  <math>{{\lambda }_{i}}{{(T)}_{U}}</math>  can be obtained from Eqn. (amsaac14).
<br>
<br>
'''Example 2'''
<br>
Calculate the 90% 2-sided confidence bounds on the cumulative and instantaneous failure intensity for the data from Example 1 given in Table 5.1. 
 
'''Solution'''
'''Fisher Matrix Bounds'''
<br>
Using  <math>\widehat{\beta }</math>  and  <math>\widehat{\lambda }</math>  estimated in Example 1, Eqns. (lambda2partial), (beta2partial) and (lambdabeta2partial) are:
 
::<math>\begin{align}
  & \frac{{{\partial }^{2}}\Lambda }{\partial {{\lambda }^{2}}}= & -\frac{22}{{{0.4239}^{2}}}=-122.43 \\
& \frac{{{\partial }^{2}}\Lambda }{\partial {{\beta }^{2}}}= & -\frac{22}{{{0.6142}^{2}}}-0.4239\cdot {{620}^{0.6142}}{{(\ln 620)}^{2}}=-967.68 \\
& \frac{{{\partial }^{2}}\Lambda }{\partial \lambda \partial \beta }= & -{{620}^{0.6142}}\ln 620=-333.64 
\end{align}</math>
 
<br>
The Fisher Matrix then becomes:
<br>
For  <math>T=620</math>  hr, the partial derivatives of the cumulative and instantaneous failure intensities are:
 
<br>
::<math>\begin{align}
  & \frac{\partial {{\lambda }_{c}}(T)}{\partial \beta }= & \widehat{\lambda }{{T}^{\widehat{\beta }-1}}\ln (T) \\
& = & 0.4239\cdot {{620}^{-0.3858}}\ln 620 \\
& = & 0.22811336 \\
& \frac{\partial {{\lambda }_{c}}(T)}{\partial \lambda }= & {{T}^{\widehat{\beta }-1}} \\
& = & {{620}^{-0.3858}} \\
& = & 0.083694185 
\end{align}</math>
 
<br>
::<math>\begin{align}
  & \frac{\partial {{\lambda }_{i}}(T)}{\partial \beta }= & \widehat{\lambda }{{T}^{\widehat{\beta }-1}}+\widehat{\lambda }\widehat{\beta }{{T}^{\widehat{\beta }-1}}\ln T \\
& = & 0.4239\cdot {{620}^{-0.3858}}+0.4239\cdot 0.6142\cdot {{620}^{-0.3858}}\ln 620 \\
& = & 0.17558519 
\end{align}</math>
<br>
::<math>\begin{align}
  & \frac{\partial {{\lambda }_{i}}(T)}{\partial \lambda }= & \widehat{\beta }{{T}^{\widehat{\beta }-1}} \\
& = & 0.6142\cdot {{620}^{-0.3858}} \\
& = & 0.051404969 
\end{align}</math>
 
Therefore, the variances become:
 
<br>
The cumulative and instantaneous failure intensities at  <math>T=620</math>  hr are:
<br>
::<math>\begin{align}
  & {{\lambda }_{c}}(T)= & 0.03548 \\
& {{\lambda }_{i}}(T)= & 0.02179 
\end{align}</math>
 
So, at the 90% confidence level and for  <math>T=620</math>  hr, the Fisher Matrix confidence bounds for the cumulative failure intensity are:
 
::<math>\begin{align}
  & {{[{{\lambda }_{c}}(T)]}_{L}}= & 0.02499 \\
& {{[{{\lambda }_{c}}(T)]}_{U}}= & 0.05039 
\end{align}</math>
 
The confidence bounds for the instantaneous failure intensity are:
 
::<math>\begin{align}
  & {{[{{\lambda }_{i}}(T)]}_{L}}= & 0.01327 \\
& {{[{{\lambda }_{i}}(T)]}_{U}}= & 0.03579 
\end{align}</math>
 
Figures 4fig82 and 4fig83 display plots of the Fisher Matrix confidence bounds for the cumulative and instantaneous failure intensity, respectively.
<br>
[[Image:rga5.2.png|thumb|center|400px|Cumulative failure intensity with 2-sided 90% Fisher Matrix confidence bounds.]]
<br>
[[Image:rga5.3.png|thumb|center|400px|Instantaneous failure intensity with 2-sided 90% Fisher Matrix confidence bounds.]]
<br>
'''Crow Bounds'''
<br>
The Crow confidence bounds for the cumulative failure intensity at the 90% confidence level and for  <math>T=620</math>  hr are:
 
::<math>\begin{align}
  & {{[{{\lambda }_{c}}(T)]}_{L}}= & \frac{\chi _{\tfrac{\alpha }{2},2N}^{2}}{2\cdot t} \\
& = & \frac{29.787476}{2*620} \\
& = & 0.02402 \\
& {{[{{\lambda }_{c}}(T)]}_{U}}= & \frac{\chi _{1-\tfrac{\alpha }{2},2N+2}^{2}}{2\cdot t} \\
& = & \frac{62.8296}{2*620} \\
& = & 0.05067 
\end{align}</math>
 
The Crow confidence bounds for the instantaneous failure intensity at the 90% confidence level and for  <math>T=620</math>  hr are:
 
::<math>\begin{align}
  & {{[{{\lambda }_{i}}(t)]}_{L}}= & \frac{1}{{{[MTB{{F}_{i}}]}_{U}}} \\
& = & \frac{1}{MTB{{F}_{i}}\cdot U} \\
& = & 0.01179 
\end{align}</math>
 
::<math>\begin{align}
  & {{[{{\lambda }_{i}}(t)]}_{U}}= & \frac{1}{{{[MTB{{F}_{i}}]}_{L}}} \\
& = & \frac{1}{MTB{{F}_{i}}\cdot L} \\
& = & 0.03253 
\end{align}</math>
 
Figures 4fig84 and 4fig85 display plots of the Crow confidence bounds for the cumulative and instantaneous failure intensity, respectively.
<br>
[[Image:rga5.4.png|thumb|center|400px|Cumulative failure intensity with 2-sided 90% Crow confidence bounds.]]
<br>
[[Image:rga5.5.png|thumb|center|400px|Instantaneous failure intensity with 2-sided 90% Crow confidence bounds.]]
<br>
::<math>\begin{align}
  & Var(\widehat{\lambda })= & 0.13519969 \\
& Var(\widehat{\beta })= & 0.017105343 \\
& Cov(\widehat{\beta },\widehat{\lambda })= & -0.046614609 
\end{align}</math>
'''Example 3'''
<br>
Calculate the confidence bounds on the cumulative and instantaneous MTBF for the data in Table 5.1.
<br>
'''Solution'''
<br>
'''Fisher Matrix Bounds'''
<br>
From the previous example:
 
And for  <math>T=620</math>  hr, the partial derivatives of the cumulative and instantaneous MTBF are:
 
::<math>\begin{align}
  & \frac{\partial {{m}_{c}}(T)}{\partial \beta }= & -\frac{1}{\widehat{\lambda }}{{T}^{1-\widehat{\beta }}}\ln T \\
& = & -\frac{1}{0.4239}{{620}^{0.3858}}\ln 620 \\
& = & -181.23135 \\
& \frac{\partial {{m}_{c}}(T)}{\partial \lambda }= & -\frac{1}{{{\widehat{\lambda }}^{2}}}{{T}^{1-\widehat{\beta }}} \\
& = & -\frac{1}{{{0.4239}^{2}}}{{620}^{0.3858}} \\
& = & -66.493299 \\
& \frac{\partial {{m}_{i}}(T)}{\partial \beta }= & -\frac{1}{\widehat{\lambda }{{\widehat{\beta }}^{2}}}{{T}^{1-\beta }}-\frac{1}{\widehat{\lambda }\widehat{\beta }}{{T}^{1-\widehat{\beta }}}\ln T \\
& = & -\frac{1}{0.4239\cdot {{0.6142}^{2}}}{{620}^{0.3858}}-\frac{1}{0.4239\cdot 0.6142}{{620}^{0.3858}}\ln 620 \\
& = & -369.78634 \\
& \frac{\partial {{m}_{i}}(T)}{\partial \lambda }= & -\frac{1}{{{\widehat{\lambda }}^{2}}\widehat{\beta }}{{T}^{1-\widehat{\beta }}} \\
& = & -\frac{1}{{{0.4239}^{2}}\cdot 0.6142}\cdot {{620}^{0.3858}} \\
& = & -108.26001 
\end{align}</math>
 
Therefore, the variances become:
 
::<math>\begin{align}
  & Var({{\widehat{m}}_{c}}(T))= & {{\left( -181.23135 \right)}^{2}}\cdot 0.017105343+{{\left( -66.493299 \right)}^{2}}\cdot 0.13519969 \\
&  & -2\cdot \left( -181.23135 \right)\cdot \left( -66.493299 \right)\cdot 0.046614609 \\
& = & 36.113376 
\end{align}</math>
 
::<math>\begin{align}
  & Var({{\widehat{m}}_{i}}(T))= & {{\left( -369.78634 \right)}^{2}}\cdot 0.017105343+{{\left( -108.26001 \right)}^{2}}\cdot 0.13519969 \\
&  & -2\cdot \left( -369.78634 \right)\cdot \left( -108.26001 \right)\cdot 0.046614609 \\
& = & 191.33709 
\end{align}</math>
 
So, at 90% confidence level and  <math>T=620</math>  hr, the Fisher Matrix confidence bounds are:
 
::<math>\begin{align}
  & {{[{{m}_{c}}(T)]}_{L}}= & {{{\hat{m}}}_{c}}(t){{e}^{-{{z}_{\alpha }}\sqrt{Var({{{\hat{m}}}_{c}}(t))}/{{{\hat{m}}}_{c}}(t)}} \\
& = & 19.84581 \\
& {{[{{m}_{c}}(T)]}_{U}}= & {{{\hat{m}}}_{c}}(t){{e}^{{{z}_{\alpha }}\sqrt{Var({{{\hat{m}}}_{c}}(t))}/{{{\hat{m}}}_{c}}(t)}} \\
& = & 40.01927 
\end{align}</math>
<br>
::<math>\begin{align}
  & {{[{{m}_{i}}(T)]}_{L}}= & {{{\hat{m}}}_{i}}(t){{e}^{-{{z}_{\alpha }}\sqrt{Var({{{\hat{m}}}_{i}}(t))}/{{{\hat{m}}}_{i}}(t)}} \\
& = & 27.94261 \\
& {{[{{m}_{i}}(T)]}_{U}}= & {{{\hat{m}}}_{i}}(t){{e}^{{{z}_{\alpha }}\sqrt{Var({{{\hat{m}}}_{i}}(t))}/{{{\hat{m}}}_{i}}(t)}} \\
& = & 75.34193 
\end{align}</math>
 
Figures 4fig86 and 4fig87 show plots of the Fisher Matrix confidence bounds for the cumulative and instantaneous MTBFs.
<br>
[[Image:rga5.6.png|thumb|center|400px|Cumulative MTBF with 2-sided 90% Fisher Matrix confidence bounds.]]
<br>
<br>
[[Image:rga5.7.png|thumb|center|400px|Instantaneous MTBF with 2-sided Fisher Matrix confidence bounds.]]
<br>
'''Crow Bounds'''
<br>
The Crow confidence bounds for the cumulative MTBF and the instantaneous MTBF at the 90% confidence level and for  <math>T=620</math>  hr are:
 
::<math>\begin{align}
  & {{[{{m}_{c}}(T)]}_{L}}= & \frac{1}{{{[{{\lambda }_{c}}(T)]}_{U}}} \\
& = & 20.5023 \\
& {{[{{m}_{c}}(T)]}_{U}}= & \frac{1}{{{[{{\lambda }_{c}}(T)]}_{L}}} \\
& = & 41.6282 
\end{align}</math>
 
::<math>\begin{align}
  & {{[MTB{{F}_{i}}]}_{L}}= & MTB{{F}_{i}}\cdot {{\Pi }_{1}} \\
& = & 30.7445 \\
& {{[MTB{{F}_{i}}]}_{U}}= & MTB{{F}_{i}}\cdot {{\Pi }_{2}} \\
& = & 84.7972 
\end{align}</math>
 
Figures 4fig88 and 4fig89 show plots of the Crow confidence bounds for the cumulative and instantaneous MTBF.
<br>
[[Image:rga5.8.png|thumb|center|400px|Cumulative MTBF with 2-sided 90% Crow confidence bounds.]]
<br>
[[Image:rga5.9.png|thumb|center|400px|Instantaneous MTBF with 2-sided 90% Crow confidence bounds.]]
Confidence bounds can also be obtained on the parameters  <math>\widehat{\beta }</math>  and  <math>\widehat{\lambda }</math> . For Fisher Matrix confidence bounds:
 
::<math>\begin{align}
  & {{\beta }_{L}}= & \hat{\beta }{{e}^{{{z}_{\alpha }}\sqrt{Var(\hat{\beta })}/\hat{\beta }}} \\
& = & 0.4325 \\
& {{\beta }_{U}}= & \hat{\beta }{{e}^{-{{z}_{\alpha }}\sqrt{Var(\hat{\beta })}/\hat{\beta }}} \\
& = & 0.8722 
\end{align}</math>
<br>
:and:
<br>
::<math>\begin{align}
  & {{\lambda }_{L}}= & \hat{\lambda }{{e}^{{{z}_{\alpha }}\sqrt{Var(\hat{\lambda })}/\hat{\lambda }}} \\
& = & 0.1016 \\
& {{\lambda }_{U}}= & \hat{\lambda }{{e}^{-{{z}_{\alpha }}\sqrt{Var(\hat{\lambda })}/\hat{\lambda }}} \\
& = & 1.7691 
\end{align}</math>
<br>
For Crow confidence bounds:
 
::<math>\begin{align}
  & {{\beta }_{L}}= & 0.4527 \\
& {{\beta }_{U}}= & 0.9350 
\end{align}</math>
<br>
:and:
<br>
::<math>\begin{align}
  & {{\lambda }_{L}}= & 0.2870 \\
& {{\lambda }_{U}}= & 0.5827 
\end{align}</math>
 
==Grouped Data==
For analyzing grouped data, we follow the same logic described in Chapter 4 for the Duane model. If Eqn. (amsaa2a) is linearized:
 
::<math>\ln [E(N(T))]=\ln \lambda +\beta \ln T</math>
 
According to Crow [9], the likelihood function for the grouped data case, (where  <math>{{n}_{1}},</math>  <math>{{n}_{2}},</math>  <math>{{n}_{3}},\ldots ,</math>  <math>{{n}_{k}}</math>  failures are observed and  <math>k</math>  is the number of groups), is:
 
::<math>\underset{i=1}{\overset{k}{\mathop \prod }}\,\underset{}{\overset{}{\mathop{\Pr }}}\,({{N}_{i}}={{n}_{i}})=\underset{i=1}{\overset{k}{\mathop \prod }}\,\frac{{{(\lambda T_{i}^{\beta }-\lambda T_{i-1}^{\beta })}^{{{n}_{i}}}}\cdot {{e}^{-(\lambda T_{i}^{\beta }-\lambda T_{i-1}^{\beta })}}}{{{n}_{i}}!}</math>
 
And the MLE of  <math>\lambda </math>  based on this relationship is:
 
::<math>\widehat{\lambda }=\frac{n}{T_{k}^{\widehat{\beta }}}</math>
 
And the estimate of  <math>\beta </math>  is the value  <math>\widehat{\beta }</math>  that satisfies:
 
::<math>\underset{i=1}{\overset{k}{\mathop \sum }}\,{{n}_{i}}\left[ \frac{T_{i}^{\widehat{\beta }}\ln {{T}_{i}}-T_{i-1}^{\widehat{\beta }}\ln {{T}_{i-1}}}{T_{i}^{\widehat{\beta }}-T_{i-1}^{\widehat{\beta }}}-\ln {{T}_{k}} \right]=0</math>
 
'''Example 4'''
<br>
Consider the grouped failure times data given in Table 5.2. Solve for the Crow-AMSAA parameters using MLE.
<br>
{|style= align="center" border="1"
|+'''Table 5.2 - Grouped failure times data'''
!Run Number
!Cumulative Failures
!End Time(hr)
!<math>\ln{(T_i)}</math>
!<math>\ln{(T_i)^2}</math>
!<math>\ln{(\theta_i)}</math>
!<math>\ln{(T_i)}\cdot\ln{(\theta_i)}</math>
|-
|1|| 2|| 200|| 5.298|| 28.072|| 0.693|| 3.673
|-
|2|| 3|| 400|| 5.991 ||35.898|| 1.099|| 6.582
|-
|3|| 4|| 600|| 6.397|| 40.921|| 1.386|| 8.868
|-
|4|| 11|| 3000|| 8.006|| 64.102|| 2.398 ||19.198
|-
| ||   ||<span style="color:blue">Sum =</span>|| <span style="color:blue">25.693</span> ||<span style="color:blue">168.992</span>||<span style="color:blue">5.576</span>||<span style="color:blue">38.321</span>
|}
 
'''Solution'''
To obtain the estimator of  <math>\beta </math> , Eqn. (vv) must be solved numerically for  <math>\beta </math> . Using RGA, the value of  <math>\widehat{\beta }</math>  is  <math>0.6315</math> . Now plugging this value into Eqn. (vv1), the estimator of  <math>\lambda </math>  is:
 
::<math>\begin{align}
  & \widehat{\lambda }= & \frac{11}{3,{{000}^{0.6315}}} \\
& = & 0.0701 
\end{align}</math>
 
Therefore, the intensity function becomes:
 
::<math>\widehat{\rho }(T)=0.0701\cdot 0.6315\cdot {{T}^{-0.3685}}</math>
 
==Grouped Data Confidence Bounds==
===Bounds on  <math>\beta </math>===
====Fisher Matrix Bounds====
The parameter  <math>\beta </math>  must be positive, thus  <math>\ln \beta </math>  is treated as being normally distributed as well. 
 
::<math>\frac{\ln \hat{\beta }-\ln \beta }{\sqrt{Var(\ln \hat{\beta }})}\ \tilde{\ }\ N(0,1)</math>
 
The approximate confidence bounds are given as:
 
::<math>C{{B}_{\beta }}=\hat{\beta }{{e}^{\pm {{z}_{\alpha }}\sqrt{Var(\hat{\beta })}/\hat{\beta }}}</math>
 
::<math>\widehat{\beta }</math>  can be obtained by  <math>\underset{i=1}{\overset{K}{\mathop{\sum }}}\,{{n}_{i}}\left( \tfrac{T_{i}^{{\hat{\beta }}}\ln {{T}_{i}}-T_{i-1}^{{\hat{\beta }}}\ln \,{{T}_{i-1}}}{T_{i}^{{\hat{\beta }}}-T_{i-1}^{{\hat{\beta }}}}-\ln {{T}_{k}} \right)=0</math> .
<br>
All variance can be calculated using the Fisher Matrix:
 
::<math>\left[ \begin{matrix}
  -\tfrac{{{\partial }^{2}}\Lambda }{\partial {{\lambda }^{2}}} & -\tfrac{{{\partial }^{2}}\Lambda }{\partial \lambda \partial \beta }  \\
  -\tfrac{{{\partial }^{2}}\Lambda }{\partial \lambda \partial \beta } & -\tfrac{{{\partial }^{2}}\Lambda }{\partial {{\beta }^{2}}}  \\
\end{matrix} \right]_{\beta =\widehat{\beta },\lambda =\widehat{\lambda }}^{-1}=\left[ \begin{matrix}
  Var(\widehat{\lambda }) & Cov(\widehat{\beta },\widehat{\lambda })  \\
  Cov(\widehat{\beta },\widehat{\lambda }) & Var(\widehat{\beta })  \\
\end{matrix} \right]</math>
 
<br>
<math>\Lambda </math>  is the natural log-likelihood function where ln <math>^{2}T={{\left( \ln T \right)}^{2}}</math>  and:
 
::<math>\Lambda =\underset{i=1}{\overset{k}{\mathop \sum }}\,\left[ {{n}_{i}}\ln (\lambda T_{i}^{\beta }-\lambda T_{i-1}^{\beta })-(\lambda T_{i}^{\beta }-\lambda T_{i-1}^{\beta })-\ln {{n}_{i}}! \right]</math>
 
::<math>\begin{align}
  & \frac{{{\partial }^{2}}\Lambda }{\partial {{\lambda }^{2}}}= & -\frac{n}{{{\lambda }^{2}}} \\
& \frac{{{\partial }^{2}}\Lambda }{\partial {{\beta }^{2}}}= & \underset{i=1}{\overset{k}{\mathop \sum }}\,\left[ \begin{matrix}
  {{n}_{i}}\left( \tfrac{(T_{i}^{{\hat{\beta }}}{{\ln }^{2}}{{T}_{i}}-T_{i-1}^{{\hat{\beta }}}{{\ln }^{2}}{{T}_{i-1}})(T_{i}^{{\hat{\beta }}}-T_{i-1}^{{\hat{\beta }}})-{{\left( T_{i}^{{\hat{\beta }}}\ln {{T}_{i}}-T_{i-1}^{{\hat{\beta }}}\ln {{T}_{i-1}} \right)}^{2}}}{{{(T_{i}^{{\hat{\beta }}}-T_{i-1}^{{\hat{\beta }}})}^{2}}} \right)  \\
  -\left( \lambda T_{i}^{{\hat{\beta }}}{{\ln }^{2}}{{T}_{i}}-\lambda T_{i-1}^{{\hat{\beta }}}{{\ln }^{2}}{{T}_{i-1}} \right)  \\
\end{matrix} \right] \\
& \frac{{{\partial }^{2}}\Lambda }{\partial \lambda \partial \beta }= & -T_{K}^{\beta }\ln {{T}_{k}} 
\end{align}</math>
 
====Crow Bounds====
:Step 1: Calculate  <math>P(i)=\tfrac{{{T}_{i}}}{{{T}_{K}}},\,\,i=1,2,\ldots ,K</math> .
:Step 2: Calculate:
 
::<math>A=\underset{i=1}{\overset{K}{\mathop \sum }}\,\frac{{{[P{{(i)}^{{\hat{\beta }}}}\ln P{{(i)}^{{\hat{\beta }}}}-P{{(i-1)}^{\widehat{\beta }}}\ln P{{(i-1)}^{{\hat{\beta }}}}]}^{2}}}{[P{{(i)}^{{\hat{\beta }}}}-P{{(i-1)}^{{\hat{\beta }}}}]}</math>
 
:Step 3: Calculate  <math>c=\tfrac{1}{\sqrt{A}}</math>  and  <math>S=\tfrac{({{z}_{1-\alpha /2}})\cdot C}{\sqrt{N}}</math> . Thus an approximate 2-sided  <math>(1-\alpha )</math> 100-percent confidence interval on  <math>\widehat{\beta }</math>  is:
 
===Bounds on  <math>\lambda </math>===
====Fisher Matrix Bounds====
The parameter  <math>\lambda </math>  must be positive, thus  <math>\ln \lambda </math>  is treated as being normally distributed as well. These bounds are based on:
 
::<math>\frac{\ln \hat{\lambda }-\ln \lambda }{\sqrt{Var(\ln \hat{\lambda }})}\ \tilde{\ }\
<math>\hat{\beta }(1\pm S)</math>
::<math>N(0,1)</math>
 
The approximate confidence bounds on  <math>\lambda </math>  are given as:
 
::<math>C{{B}_{\lambda }}=\hat{\lambda }{{e}^{\pm {{z}_{\alpha }}\sqrt{Var(\hat{\lambda })}/\hat{\lambda }}}</math>
 
:where:
 
::<math>\hat{\lambda }=\frac{n}{T_{k}^{{\hat{\beta }}}}</math>
 
The variance calculation is the same as Eqn. (variances).
 
====Crow Bounds====
<br>
'''Time Terminated Data'''
<br>
For the 2-sided  <math>(1-\alpha )</math> 100-percent confidence interval, the confidence bounds on  <math>\lambda </math>  are:
 
::<math>\begin{align}
  & {{\lambda }_{L}}= & \frac{\chi _{\tfrac{\alpha }{2},2N}^{2}}{2\cdot T_{k}^{\beta }} \\
& {{\lambda }_{U}}= & \frac{\chi _{1-\tfrac{\alpha }{2},2N+2}^{2}}{2\cdot T_{k}^{\beta }} 
\end{align}</math>
 
'''Failure Terminated Data'''
<br>
For the 2-sided  <math>(1-\alpha )</math> 100-percent confidence interval, the confidence bounds on  <math>\lambda </math>  are:
 
::<math>\begin{align}
  & {{\lambda }_{L}}= & \frac{\chi _{\tfrac{\alpha }{2},2N}^{2}}{2\cdot T_{k}^{\beta }} \\
& {{\lambda }_{U}}= & \frac{\chi _{1-\tfrac{\alpha }{2},2N}^{2}}{2\cdot T_{k}^{\beta }} 
\end{align}</math>
 
===Bounds on Growth Rate===
====Fisher Matrix Bounds====
Since the growth rate is equal to  <math>1-\beta </math> , the confidence bounds are calculated from:
 
::<math>\begin{align}
  & G\operatorname{row}th\text{ }Rat{{e}_{L}}= & 1-{{\beta }_{U}} \\
& G\operatorname{row}th\text{ }Rat{{e}_{U}}= & 1-{{\beta }_{L}} 
\end{align}</math>
 
For the Fisher Matrix confidence bounds,  <math>{{\beta }_{L}}</math>  and  <math>{{\beta }_{U}}</math>  are obtained from Eqn. (Gcbb). For the Crow bounds,  <math>{{\beta }_{L}}</math>  and  <math>{{\beta }_{U}}</math>  are obtained from Eqn. (gcbb).
 
===Bounds on Cumulative MTBF===
====Fisher Matrix Bounds====
The cumulative MTBF,  <math>{{m}_{c}}(t)</math> , must be positive, thus  <math>\ln {{m}_{c}}(t)</math>  is treated as being normally distributed as well.
 
::<math>\frac{\ln {{{\hat{m}}}_{c}}(t)-\ln {{m}_{c}}(t)}{\sqrt{Var(\ln {{{\hat{m}}}_{c}}(t)})}\ \tilde{\ }\ N(0,1)</math>
 
The approximate confidence bounds on the cumulative MTBF are then estimated from:
 
::<math>CB={{\hat{m}}_{c}}(t){{e}^{\pm {{z}_{\alpha }}\sqrt{Var({{{\hat{m}}}_{c}}(t))}/{{{\hat{m}}}_{c}}(t)}}</math>
 
:where:
 
<br>
::<math>{{\hat{m}}_{c}}(t)=\frac{1}{{\hat{\lambda }}}{{t}^{1-\hat{\beta }}}</math>
 
::<math>\begin{align}
  & Var({{{\hat{m}}}_{c}}(t))= & {{\left( \frac{\partial {{m}_{c}}(t)}{\partial \beta } \right)}^{2}}Var(\hat{\beta })+{{\left( \frac{\partial {{m}_{c}}(t)}{\partial \lambda } \right)}^{2}}Var(\hat{\lambda }) \\
&  & +2\left( \frac{\partial {{m}_{c}}(t)}{\partial \beta } \right)\left( \frac{\partial {{m}_{c}}(t)}{\partial \lambda } \right)cov(\hat{\beta },\hat{\lambda })\, 
\end{align}</math>
 
The variance calculation is the same as Eqn. (variances) and:
 
::<math>\begin{align}
  & \frac{\partial {{m}_{c}}(t)}{\partial \beta }= & -\frac{1}{{\hat{\lambda }}}{{t}^{1-\hat{\beta }}}\ln t \\
& \frac{\partial {{m}_{c}}(t)}{\partial \lambda }= & -\frac{1}{{{{\hat{\lambda }}}^{2}}}{{t}^{1-\hat{\beta }}} 
\end{align}</math>
 
====Crow Bounds====
Calculate the Crow cumulative failure intensity confidence bounds:
 
::<math>C{{(t)}_{L}}=\frac{\chi _{\tfrac{\alpha }{2},2N}^{2}}{2\cdot t}</math>
 
::<math>C{{(t)}_{U}}=\frac{\chi _{1-\tfrac{\alpha }{2},2N+2}^{2}}{2\cdot t}</math>
 
:Then:
 
::<math>\begin{align}
  & {{[MTB{{F}_{c}}]}_{L}}= & \frac{1}{C{{(t)}_{U}}} \\
& {{[MTB{{F}_{c}}]}_{U}}= & \frac{1}{C{{(t)}_{L}}} 
\end{align}</math>
 
===Bounds on Instantaneous MTBF===
====Fisher Matrix Bounds====
The instantaneous MTBF,  <math>{{m}_{i}}(t)</math> , must be positive, thus  <math>\ln {{m}_{i}}(t)</math>  is approximately treated as being normally distributed as well.
 
::<math>\frac{\ln {{{\hat{m}}}_{i}}(t)-\ln {{m}_{i}}(t)}{\sqrt{Var(\ln {{{\hat{m}}}_{i}}(t)})}\ \tilde{\ }\ N(0,1)</math>
 
The approximate confidence bounds on the instantaneous MTBF are then estimated from:
 
::<math>CB={{\hat{m}}_{i}}(t){{e}^{\pm {{z}_{\alpha }}\sqrt{Var({{{\hat{m}}}_{i}}(t))}/{{{\hat{m}}}_{i}}(t)}}</math>
 
:where:
 
::<math>{{\hat{m}}_{i}}(t)=\frac{1}{\lambda \beta {{t}^{\beta -1}}}</math>
 
::<math>\begin{align}
  & Var({{{\hat{m}}}_{i}}(t))= & {{\left( \frac{\partial {{m}_{i}}(t)}{\partial \beta } \right)}^{2}}Var(\hat{\beta })+{{\left( \frac{\partial {{m}_{i}}(t)}{\partial \lambda } \right)}^{2}}Var(\hat{\lambda }) \\
&  & +2\left( \frac{\partial {{m}_{i}}(t)}{\partial \beta } \right)\left( \frac{\partial {{m}_{i}}(t)}{\partial \lambda } \right)cov(\hat{\beta },\,\,\,\hat{\lambda }) 
\end{align}</math>
 
The variance calculation is the same as Eqn. (variances) and:
 
::<math>\begin{align}
  & \frac{\partial {{m}_{i}}(t)}{\partial \beta }= & -\frac{1}{\hat{\lambda }{{{\hat{\beta }}}^{2}}}{{t}^{1-\hat{\beta }}}-\frac{1}{\hat{\lambda }\hat{\beta }}{{t}^{1-\hat{\beta }}}\ln t \\
& \frac{\partial {{m}_{i}}(t)}{\partial \lambda }= & -\frac{1}{{{{\hat{\lambda }}}^{2}}\hat{\beta }}{{t}^{1-\hat{\beta }}} 
\end{align}</math>
 
====Crow Bounds====
:Step 1: Calculate  <math>P(i)=\tfrac{{{T}_{i}}}{{{T}_{K}}},\,\,i=1,2,\ldots ,K</math> .
:Step 2: Calculate:
 
::<math>A=\underset{i=1}{\overset{K}{\mathop \sum }}\,\frac{{{\left[ P{{(i)}^{{\hat{\beta }}}}\ln P{{(i)}^{{\hat{\beta }}}}-P{{(i-1)}^{\widehat{\beta }}}\ln P{{(i-1)}^{{\hat{\beta }}}} \right]}^{2}}}{\left[ P{{(i)}^{{\hat{\beta }}}}-P{{(i-1)}^{{\hat{\beta }}}} \right]}</math>
 
:Step 3: Calculate  <math>D=\sqrt{\tfrac{1}{A}+1}</math>  and  <math>W=\tfrac{({{z}_{1-\alpha /2}})\cdot D}{\sqrt{N}}</math> . Thus an approximate 2-sided  <math>(1-\alpha )</math> 100-percent confidence interval on  <math>{{\hat{m}}_{i}}(t)</math>  is:
 
::<math>MTB{{F}_{i}}={{\widehat{m}}_{i}}(1\pm W)</math>
 
===Bounds on Cumulative Failure Intensity===
====Fisher Matrix Bounds====
The cumulative failure intensity,  <math>{{\lambda }_{c}}(t)</math> , must be positive, thus  <math>\ln {{\lambda }_{c}}(t)</math>  is treated as being normally distributed. 
 
::<math>\frac{\ln {{{\hat{\lambda }}}_{c}}(t)-\ln {{\lambda }_{c}}(t)}{\sqrt{Var(\ln {{{\hat{\lambda }}}_{c}}(t)})}\ \tilde{\ }\ N(0,1)</math>
 
The approximate confidence bounds on the cumulative failure intensity are then estimated from:
 
::<math>CB={{\hat{\lambda }}_{c}}(t){{e}^{\pm {{z}_{\alpha }}\sqrt{Var({{{\hat{\lambda }}}_{c}}(t))}/{{{\hat{\lambda }}}_{c}}(t)}}</math>
 
:where:
 
<br>
::<math>{{\hat{\lambda }}_{c}}(t)=\hat{\lambda }{{t}^{\hat{\beta }-1}}</math>
<br>
:and:
<br>
::<math>\begin{align}
  & Var({{{\hat{\lambda }}}_{c}}(t))= & {{\left( \frac{\partial {{\lambda }_{c}}(t)}{\partial \beta } \right)}^{2}}Var(\hat{\beta })+{{\left( \frac{\partial {{\lambda }_{c}}(t)}{\partial \lambda } \right)}^{2}}Var(\hat{\lambda }) \\
&  & +2\left( \frac{\partial {{\lambda }_{c}}(t)}{\partial \beta } \right)\left( \frac{\partial {{\lambda }_{c}}(t)}{\partial \lambda } \right)cov(\hat{\beta },\,\,\,\hat{\lambda }) 
\end{align}</math>
 
The variance calculation is the same as Eqn. (variances) and:
 
::<math>\begin{align}
  & \frac{\partial {{\lambda }_{c}}(t)}{\partial \beta }= & \hat{\lambda }{{t}^{\hat{\beta }-1}}\ln t \\
& \frac{\partial {{\lambda }_{c}}(t)}{\partial \lambda }= & {{t}^{\hat{\beta }-1}} 
\end{align}</math>
 
====Crow Bounds====
The Crow cumulative failure intensity confidence bounds are given as:
 
::<math>\begin{align}
  & C{{(t)}_{L}}= & \frac{\chi _{\tfrac{\alpha }{2},2N}^{2}}{2\cdot t} \\
& C{{(t)}_{U}}= & \frac{\chi _{1-\tfrac{\alpha }{2},2N+2}^{2}}{2\cdot t} 
\end{align}</math>
 
===Bounds on Instantaneous Failure Intensity===
====Fisher Matrix Bounds====
The instantaneous failure intensity,  <math>{{\lambda }_{i}}(t)</math> , must be positive, thus  <math>\ln {{\lambda }_{i}}(t)</math>  is treated as being normally distributed.
 
::<math>\frac{\ln {{{\hat{\lambda }}}_{i}}(t)-\ln {{\lambda }_{i}}(t)}{\sqrt{Var(\ln {{{\hat{\lambda }}}_{i}}(t)})}\tilde{\ }N(0,1)</math>
 
The approximate confidence bounds on the instantaneous failure intensity are then estimated from:
 
::<math>CB={{\hat{\lambda }}_{i}}(t){{e}^{\pm {{z}_{\alpha }}\sqrt{Var({{{\hat{\lambda }}}_{i}}(t))}/{{{\hat{\lambda }}}_{i}}(t)}}</math>
 
 
where  <math>{{\lambda }_{i}}(t)=\lambda \beta {{t}^{\beta -1}}</math>  and:
 
::<math>\begin{align}
  & Var({{{\hat{\lambda }}}_{i}}(t))= & {{\left( \frac{\partial {{\lambda }_{i}}(t)}{\partial \beta } \right)}^{2}}Var(\hat{\beta })+{{\left( \frac{\partial {{\lambda }_{i}}(t)}{\partial \lambda } \right)}^{2}}Var(\hat{\lambda }) \\
&  & +2\left( \frac{\partial {{\lambda }_{i}}(t)}{\partial \beta } \right)\left( \frac{\partial {{\lambda }_{i}}(t)}{\partial \lambda } \right)cov(\hat{\beta },\,\,\,\hat{\lambda }) 
\end{align}</math>
 
The variance calculation is the same as Eqn. (variances) and:
 
::<math>\begin{align}
  & \frac{\partial {{\lambda }_{i}}(t)}{\partial \beta }= & \hat{\lambda }{{t}^{\hat{\beta }-1}}+\hat{\lambda }\hat{\beta }{{t}^{\hat{\beta }-1}}\ln t \\
& \frac{\partial {{\lambda }_{i}}(t)}{\partial \lambda }= & \hat{\beta }{{t}^{\hat{\beta }-1}} 
\end{align}</math>
 
====Crow Bounds====
The Crow instantaneous failure intensity confidence bounds are given as:
 
::<math>\begin{align}
  & {{[{{\lambda }_{i}}(t)]}_{L}}= & \frac{1}{{{[MTB{{F}_{i}}]}_{U}}} \\
& {{[{{\lambda }_{i}}(t)]}_{U}}= & \frac{1}{{{[MTB{{F}_{i}}]}_{L}}} 
\end{align}</math>
 
===Bounds on Time Given Cumulative MTBF===
====Fisher Matrix Bounds====
The time,  <math>T</math> , must be positive, thus  <math>\ln T</math>  is treated as being normally distributed.
 
::<math>\frac{\ln \hat{T}-\ln T}{\sqrt{Var(\ln \hat{T}})}\ \tilde{\ }\ N(0,1)</math>
 
Confidence bounds on the time are given by:
 
::<math>CB=\hat{T}{{e}^{\pm {{z}_{\alpha }}\sqrt{Var(\hat{T})}/\hat{T}}}</math>
 
:where:
 
::<math>\begin{align}
  & Var(\hat{T})= & {{\left( \frac{\partial T}{\partial \beta } \right)}^{2}}Var(\hat{\beta })+{{\left( \frac{\partial T}{\partial \lambda } \right)}^{2}}Var(\hat{\lambda }) \\
&  & +2\left( \frac{\partial T}{\partial \beta } \right)\left( \frac{\partial T}{\partial \lambda } \right)cov(\hat{\beta },\,\,\,\hat{\lambda }) 
\end{align}</math>
 
The variance calculation is the same as Eqn. (variances) and:
 
::<math>\hat{T}={{(\lambda \cdot {{m}_{c}})}^{1/(1-\beta )}}</math>
 
::<math>\begin{align}
  & \frac{\partial T}{\partial \beta }= & \frac{{{(\lambda \cdot \,{{m}_{c}})}^{1/(1-\beta )}}\ln (\lambda \cdot \text{ }{{m}_{c}})}{{{(1-\beta )}^{2}}} \\
& \frac{\partial T}{\partial \lambda }= & \frac{{{(\lambda \cdot {{m}_{c}})}^{1/(1-\beta )}}}{\lambda (1-\beta )} 
\end{align}</math>
 
====Crow Bounds====
:Step 1: Calculate  <math>{{\lambda }_{c}}(T)=\tfrac{1}{MTB{{F}_{c}}}</math> .
:Step 2: Use equations in 5.4.10.1 to calculate the bounds on time given the cumulative failure intensity.
 
===Bounds on Time Given Instantaneous MTBF===
====Fisher Matrix Bounds====
The time,  <math>T</math> , must be positive, thus  <math>\ln T</math>  is treated as being normally distributed.
 
::<math>\frac{\ln \hat{T}-\ln T}{\sqrt{Var(\ln \hat{T}})}\ \tilde{\ }\ N(0,1)</math>
 
Confidence bounds on the time are given by:
 
::<math>CB=\hat{T}{{e}^{\pm {{z}_{\alpha }}\sqrt{Var(\hat{T})}/\hat{T}}}</math>
 
:where:
 
::<math>\begin{align}
  & Var(\hat{T})= & {{\left( \frac{\partial T}{\partial \beta } \right)}^{2}}Var(\hat{\beta })+{{\left( \frac{\partial T}{\partial \lambda } \right)}^{2}}Var(\hat{\lambda }) \\
&  & +2\left( \frac{\partial T}{\partial \beta } \right)\left( \frac{\partial T}{\partial \lambda } \right)cov(\hat{\beta },\,\,\,\hat{\lambda }) 
\end{align}</math>
 
The variance calculation is the same as Eqn. (variances) and:
 
::<math>\hat{T}={{(\lambda \beta \cdot {{m}_{i}}(T))}^{1/(1-\beta )}}</math>
 
::<math>\begin{align}
  & \frac{\partial T}{\partial \beta }= & {{\left( \lambda \beta \cdot \text{ }{{m}_{i}}(T) \right)}^{1/(1-\beta )}}\left[ \frac{1}{{{(1-\beta )}^{2}}}\ln (\lambda \beta \cdot {{m}_{i}}(T))+\frac{1}{\beta (1-\beta )} \right] \\
& \frac{\partial T}{\partial \lambda }= & \frac{{{(\lambda \beta \cdot \text{ }{{m}_{i}}(T))}^{1/(1-\beta )}}}{\lambda (1-\beta )} 
\end{align}</math>
 
====Crow Bounds====
:Step 1: Calculate the confidence bounds on the instantaneous MTBF:
 
::<math>MTB{{F}_{i}}={{\widehat{m}}_{i}}(1\pm W)</math>
 
:Step 2: Use equations in 5.4.5.2 to calculate the time given the instantaneous MTBF.
 
===Bounds on Time Given Cumulative Failure Intensity===
====Fisher Matrix Bounds====
The time,  <math>T</math> , must be positive, thus  <math>\ln T</math>  is treated as being normally distributed.
 
::<math>\frac{\ln \hat{T}-\ln T}{\sqrt{Var(\ln \hat{T}})}\ \tilde{\ }\ N(0,1)</math>
 
Confidence bounds on the time are given by:
 
::<math>CB=\hat{T}{{e}^{\pm {{z}_{\alpha }}\sqrt{Var(\hat{T})}/\hat{T}}}</math>
 
:where:
 
::<math>\begin{align}
  & Var(\hat{T})= & {{\left( \frac{\partial T}{\partial \beta } \right)}^{2}}Var(\hat{\beta })+{{\left( \frac{\partial T}{\partial \lambda } \right)}^{2}}Var(\hat{\lambda }) \\
&  & +2\left( \frac{\partial T}{\partial \beta } \right)\left( \frac{\partial T}{\partial \lambda } \right)cov(\hat{\beta },\,\,\,\hat{\lambda }) 
\end{align}</math>
 
The variance calculation is the same as Eqn. (variances) and:
 
::<math>\begin{align}
  & \frac{\partial T}{\partial \beta }= & \frac{-{{\left( \tfrac{{{\lambda }_{c}}(T)}{\lambda } \right)}^{1/(\beta -1)}}\ln \left( \tfrac{{{\lambda }_{c}}(T)}{\lambda } \right)}{{{(1-\beta )}^{2}}} \\
& \frac{\partial T}{\partial \lambda }= & {{\left( \frac{{{\lambda }_{c}}(T)}{\lambda } \right)}^{1/(\beta -1)}}\frac{1}{\lambda (1-\beta )} 
\end{align}</math>
 
 
====Crow Bounds====
:Step 1: Calculate:
 
::<math>\hat{T}={{\left( \frac{{{\lambda }_{c}}(T)}{{\hat{\lambda }}} \right)}^{\tfrac{1}{\beta -1}}}</math>
 
:Step 2: Estimate the number of failures:
 
::<math>N(\hat{T})=\hat{\lambda }{{\hat{T}}^{{\hat{\beta }}}}</math>
 
:Step 3: Obtain the confidence bounds on time given the cumulative failure intensity by solving for  <math>{{t}_{l}}</math>  and  <math>{{t}_{u}}</math>  in the following equations:
 
::<math>\begin{align}
  & {{t}_{l}}= & \frac{\chi _{\tfrac{\alpha }{2},2N}^{2}}{2\cdot {{\lambda }_{c}}(T)} \\
& {{t}_{u}}= & \frac{\chi _{1-\tfrac{\alpha }{2},2N+2}^{2}}{2\cdot {{\lambda }_{c}}(T)} 
\end{align}</math>
 
===Bounds on Time Given Instantaneous Failure Intensity===
====Fisher Matrix Bounds====
The time,  <math>T</math> , must be positive, thus  <math>\ln T</math>  is treated as being normally distributed.
 
::<math>\frac{\ln \hat{T}-\ln T}{\sqrt{Var(\ln \hat{T}})}\ \tilde{\ }\ N(0,1)</math>
 
Confidence bounds on the time are given by:
 
::<math>CB=\hat{T}{{e}^{\pm {{z}_{\alpha }}\sqrt{Var(\hat{T})}/\hat{T}}}</math>
 
:where:
 
::<math>\begin{align}
  & Var(\hat{T})= & {{\left( \frac{\partial T}{\partial \beta } \right)}^{2}}Var(\hat{\beta })+{{\left( \frac{\partial T}{\partial \lambda } \right)}^{2}}Var(\hat{\lambda }) \\
&  & +2\left( \frac{\partial T}{\partial \beta } \right)\left( \frac{\partial T}{\partial \lambda } \right)cov(\hat{\beta },\,\,\,\hat{\lambda }) 
\end{align}</math>
 
The variance calculation is the same as Eqn. (variances) and: 
 
::<math>\hat{T}={{\left( \frac{{{\lambda }_{i}}(T)}{\lambda \beta } \right)}^{1/(\beta -1)}}</math>
 
::<math>\begin{align}
  & \frac{\partial T}{\partial \beta }= & {{\left( \frac{{{\lambda }_{i}}(T)}{\lambda \beta } \right)}^{1/(\beta -1)}}\left[ -\frac{\ln (\tfrac{{{\lambda }_{i}}(T)}{\lambda \beta })}{{{(\beta -1)}^{2}}}+\frac{1}{\beta (1-\beta )} \right] \\
& \frac{\partial T}{\partial \lambda }= & {{\left( \frac{{{\lambda }_{i}}(T)}{\lambda \beta } \right)}^{1/(\beta -1)}}\frac{1}{\lambda (1-\beta )} 
\end{align}</math>
 
 
====Crow Bounds====
:Step 1: Calculate  <math>MTB{{F}_{i}}=\tfrac{1}{{{\lambda }_{i}}(T)}</math> .
:Step 2: Follow the same process as in 5.4.9.2 to calculate the bounds on time given the instantaneous failure intensity.
 
===Bounds on Cumulative Number of Failures===
====Fisher Matrix Bounds====
The cumulative number of failures,  <math>N(t)</math> , must be positive, thus  <math>\ln N(t)</math>  is treated as being normally distributed. 
 
::<math>\frac{\ln \hat{N}(t)-\ln N(t)}{\sqrt{Var(\ln \hat{N}(t)})}\ \tilde{\ }\ N(0,1)</math>
 
::<math>N(t)=\hat{N}(t){{e}^{\pm {{z}_{\alpha }}\sqrt{Var(\hat{N}(t))}/\hat{N}(t)}}</math>
 
:where:
 
::<math>\hat{N}(t)=\hat{\lambda }{{t}^{{\hat{\beta }}}}</math>
 
 
::<math>\begin{align}
  & Var(\hat{N}(t))= & {{\left( \frac{\partial \hat{N}(t)}{\partial \beta } \right)}^{2}}Var(\hat{\beta })+{{\left( \frac{\partial \hat{N}(t)}{\partial \lambda } \right)}^{2}}Var(\hat{\lambda }) \\
&  & +2\left( \frac{\partial \hat{N}(t)}{\partial \beta } \right)\left( \frac{\partial \hat{N}(t)}{\partial \lambda } \right)cov(\hat{\beta },\hat{\lambda }) 
\end{align}</math>
 
 
The variance calculation is the same as Eqn. (variances) and: 
 
::<math>\begin{align}
  & \frac{\partial \hat{N}(t)}{\partial \beta }= & \hat{\lambda }{{t}^{{\hat{\beta }}}}\ln t \\
& \frac{\partial \hat{N}(t)}{\partial \lambda }= & {{t}^{{\hat{\beta }}}} 
\end{align}</math>
 
 
====Crow Bounds====
The Crow confidence bounds on cumulative number of failures are:
 
::<math>\begin{align}
  & {{N}_{L}}(T)= & \frac{T}{{\hat{\beta }}}{{\lambda }_{i}}{{(T)}_{L}} \\
& {{N}_{U}}(T)= & \frac{T}{{\hat{\beta }}}{{\lambda }_{i}}{{(T)}_{U}} 
\end{align}</math>
 
 
where  <math>{{\lambda }_{i}}{{(T)}_{L}}</math>  and  <math>{{\lambda }_{i}}{{(T)}_{U}}</math>  can be obtained from Eqn. (dsaf).
<br>
<br>
'''Example 5'''
<br>
A new helicopter system is under development. System failure data has been collected on five helicopters during the final test phase. The actual failure times cannot be determined since the failures are not discovered until after the helicopters are brought into the maintenance area. However, total flying hours are known when the helicopters are brought in for service and every two weeks, each helicopter undergoes a thorough inspection to uncover any failures that may have occurred since the last inspection. Therefore, the cumulative total number of flight hours and the cumulative total number of failures for the five helicopters are known for each two-week period. The total number of flight hours from the test phase is 500, which was accrued over a period of 12 weeks (6 2-week intervals). For each 2-week interval, the total number of flight hours and total number of failures for the five helicopters were recorded. The grouped data set is displayed in Table 5.3.
<br>
{|style= align="center" border="1"
|+'''Table 5.3 - Grouped data for a new helicopter system'''
!Interval
!Interval Length
!Failures in Interval
|-
|1|| 0 - 62|| 12
|-
|2|| 62 -100|| 6
|-
|3|| 100 - 187|| 15
|-
|4|| 187 - 210|| 3
|-
|5|| 210 - 350|| 18
|-
|6|| 350 - 500|| 16
|}
<br>
<br>
<br>
:1) Estimate the parameters of the Crow-AMSAA model using maximum likelihood estimation.
:2) Calculate the confidence bounds on the cumulative and instantaneous MTBF using the <br>
Fisher Matrix and Crow methods.
<br>
<br>
'''Solution'''
<br>
:1) Obtain the estimator of  <math>\beta </math>  using Eqn. (vv). Using RGA, the value of  <math>\widehat{\beta }</math>  is 0.81361. Now plug this value into Eqn. (vv1) and  <math>\widehat{\lambda }</math>  is:
<br>
::<math>\widehat{\lambda }=0.44585</math>
Fisher Matrix confidence bounds can be obtained on the parameters  <math>\widehat{\beta }</math>  and  <math>\widehat{\lambda }</math>  at the 90% confidence level by:
 
 
::<math>\begin{align}
  & {{\beta }_{L}}= & \hat{\beta }{{e}^{{{z}_{\alpha }}\sqrt{Var(\hat{\beta })}/\hat{\beta }}} \\
& = & 0.6546 \\
& {{\beta }_{U}}= & \hat{\beta }{{e}^{-{{z}_{\alpha }}\sqrt{Var(\hat{\beta })}/\hat{\beta }}} \\
& = & 1.0112 
\end{align}</math>
<br>
 
:and:
<br>
 
::<math>\begin{align}
  & {{\lambda }_{L}}= & \hat{\lambda }{{e}^{{{z}_{\alpha }}\sqrt{Var(\hat{\lambda })}/\hat{\lambda }}} \\
& = & 0.14594 \\
& {{\lambda }_{U}}= & \hat{\lambda }{{e}^{-{{z}_{\alpha }}\sqrt{Var(\hat{\lambda })}/\hat{\lambda }}} \\
& = & 1.36207 
\end{align}</math>
 
 
Crow confidence bounds can also be obtained on the parameters  <math>\widehat{\beta }</math>  and  <math>\widehat{\lambda }</math>  at the 90% confidence level, as:
 
 
::<math>\begin{align}
  & {{\beta }_{L}}= & \hat{\beta }(1-S) \\
& = & 0.63552 \\
& {{\beta }_{U}}= & \hat{\beta }(1+S) \\
& = & 0.99170 
\end{align}</math>
 
:and:
 
::<math>\begin{align}
  & {{\lambda }_{L}}= & \frac{\chi _{\tfrac{\alpha }{2},2N}^{2}}{2\cdot T_{k}^{\beta }} \\
& = & 0.36197 \\
& {{\lambda }_{U}}= & \frac{\chi _{1-\tfrac{\alpha }{2},2N+2}^{2}}{2\cdot T_{k}^{\beta }} \\
& = & 0.53697 
\end{align}</math>
 
 
:2) The Fisher Matrix confidence bounds for the cumulative MTBF and the instantaneous MTBF at the 90% 2-sided confidence level and for  <math>T=500</math>  hr are:
 
 
::<math>\begin{align}
  & {{[{{m}_{c}}(T)]}_{L}}= & {{{\hat{m}}}_{c}}(t){{e}^{{{z}_{\alpha /2}}\sqrt{Var({{{\hat{m}}}_{c}}(t))}/{{{\hat{m}}}_{c}}(t)}} \\
& = & 5.8680 \\
& {{[{{m}_{c}}(T)]}_{U}}= & {{{\hat{m}}}_{c}}(t){{e}^{-{{z}_{\alpha /2}}\sqrt{Var({{{\hat{m}}}_{c}}(t))}/{{{\hat{m}}}_{c}}(t)}} \\
& = & 8.6947 
\end{align}</math>
 
:and:
 
::<math>\begin{align}
  & {{[MTB{{F}_{i}}]}_{L}}= & {{{\hat{m}}}_{i}}(t){{e}^{{{z}_{\alpha /2}}\sqrt{Var({{{\hat{m}}}_{i}}(t))}/{{{\hat{m}}}_{i}}(t)}} \\
& = & 6.6483 \\
& {{[MTB{{F}_{i}}]}_{U}}= & {{{\hat{m}}}_{i}}(t){{e}^{-{{z}_{\alpha /2}}\sqrt{Var({{{\hat{m}}}_{i}}(t))}/{{{\hat{m}}}_{i}}(t)}} \\
& = & 11.5932 
\end{align}</math>
 
Figures 4fig810 and 4fig811 show plots of the Fisher Matrix confidence bounds for the cumulative and instantaneous MTBF.
 
<br>
[[Image:rga5.10.png|thumb|center|400px|Cumulative MTBF with 2-sided 90% Fisher Matrix confidence bounds.]]
<br>
<br>
<br>
[[Image:rga5.11.png|thumb|center|400px|Instantaneous MTBF with 2-sided 90% Fisher Matrix confidence bounds.]]
 
<br>
The Crow confidence bounds for the cumulative and instantaneous MTBF at the 90% 2-sided confidence level and for    hours are:
 
::<math>T=500</math>
::<math>\begin{align}
  & {{[{{m}_{c}}(T)]}_{L}}= & \frac{1}{C{{(t)}_{U}}} \\
& = & 5.85449 \\
& {{[{{m}_{c}}(T)]}_{U}}= & \frac{1}{C{{(t)}_{L}}} \\
& = & 8.79822 
\end{align}</math>
 
:and:
 
::<math>\begin{align}
  & {{[MTB{{F}_{i}}]}_{L}}= & {{\widehat{m}}_{i}}(1-W) \\
& = & 6.19623 \\
& {{[MTB{{F}_{i}}]}_{U}}= & {{\widehat{m}}_{i}}(1+W) \\
& = & 11.36223 
\end{align}</math>
 
Figures 4fig812 and 4fig813 show plots of the Crow confidence bounds for the cumulative and instantaneous MTBF.
 
<br>
[[Image:rga5.12.png|thumb|center|400px|Cumulative MTBF with 2-sided 90% Crow confidence bounds.]]
<br>
<br>
<br>
[[Image:rga5.13.png|thumb|center|400px|Instantaneous MTBF with 2-sided 90% Crow confidence bounds.]]
<br>
<br>
 
==Goodness-of-Fit Tests==
While using the Crow-AMSAA model in the RGA 7 software, there are four goodness-of-fit tests which may become available depending on their applicability. The Cramér-von Mises goodness-of-fit test tests the hypothesis that the data follows a nonhomogeneous Poisson process with failure intensity equal to  <math>u(t)=\lambda \beta {{t}^{\beta -1}}</math> . This test can be applied when the failure data is complete over the continuous interval  <math>[0,{{T}_{q}}]</math>  with no gaps in the data. The Chi-Squared test is a goodness-of-fit test that can be applied under more general circumstances, particularly when the data set is grouped. In addition, for multiple system data the Common Beta Hypothesis (CBH) test also can be used to compare the intensity functions of the individual systems by comparing the  <math>{{\beta }_{q}}</math>  results for each system. Lastly, the Laplace Trend test checks for trends within the data. Due to their general application to multiple models, the Common Beta Hypothesis test and the Laplace Trend test are both presented in Appendix B. The Cramér-von Mises and Chi-Squared tests are described here since they apply to the Crow-AMSAA model only.
<br>
===Cramér-von Mises Test for Individual Failure Times===
If the individual failure times are known, a Cramér-von Mises statistic is used to test the null hypothesis that a non-homogeneous Poisson process with failure intensity function  <math>\rho \left( t \right)=\lambda \,\beta \,{{t}^{\beta -1}}\left( \lambda >0,\beta >0,t>0 \right)</math>  properly describes the reliability growth of a system. The Cramér-von Mises goodness-of-fit statistic is then given by the following expression:
 
 
::<math>C_{M}^{2}=\frac{1}{12M}+\underset{i=1}{\overset{M}{\mathop \sum }}\,{{\left[ {{\left( \frac{{{T}_{i}}}{T} \right)}^{{\hat{\beta }}}}-\frac{2i-1}{2M} \right]}^{2}}</math>
 
:where:
 
::<math>M=\left\{ \begin{matrix}
  N\text{ if the test is time terminated}  \\
  N-1\text{ if the test is failure terminated}  \\
\end{matrix} \right\}</math>
 
The failure times,  <math>{{T}_{i}}</math> , must be ordered so that  <math>{{T}_{1}}<{{T}_{2}}<\ldots <{{T}_{M}}</math> .
If the statistic  <math>C_{M}^{2}</math>  exceeds the critical value corresponding to  <math>M</math>  for a chosen significance level, then the null hypothesis that the Crow-AMSAA model adequately fits the data shall be rejected. Otherwise, the model shall be accepted. Critical values of  <math>C_{M}^{2}</math>  are shown in Appendix B, Table B.2, where the table is indexed by the total number of observed failures,  <math>M</math> .
===Chi-Squared Test for Grouped Data===
A Chi-Squared goodness-of-fit test is used to test the null hypothesis that the Crow-AMSAA reliability model adequately represents a set of grouped data. The expected number of failures in the interval from  <math>{{T}_{i-1}}</math>  to  <math>{{T}_{i}}</math>  is approximated by:
 
::<math>{{\widehat{\theta }}_{i}}=\hat{\lambda }\left( T_{i}^{{\hat{\beta }}}-T_{i-1}^{{\hat{\beta }}} \right)</math>
 
For each interval,  <math>{{\widehat{\theta }}_{i}}</math>  shall not be less than 5 and, if necessary, adjacent intervals may have to be combined so that the expected number of failures in any combined interval is at least 5. Let the number of intervals after this recombination be  <math>d</math>  and let the observed number of failures in the  <math>{{i}^{th}}</math>  new interval be  <math>{{N}_{i}}</math>  and let the expected number of failures in the  <math>{{i}^{th}}</math>  new interval be  <math>{{\widehat{\theta }}_{i}}</math> . Then the following statistic is approximately distributed as a Chi-Squared random variable with degrees of freedom  <math>d-2</math> .
 
::<math>{{\chi }^{2}}=\underset{i=1}{\overset{d}{\mathop \sum }}\,\frac{{{({{N}_{i}}-{{\widehat{\theta }}_{i}})}^{2}}}{{{\widehat{\theta }}_{i}}}</math>
 
The null hypothesis is rejected if the  <math>{{\chi }^{2}}</math>  statistic exceeds the critical value for a chosen significance level. This means that the hypothesis that the Crow-AMSAA model adequately fits the grouped data shall be rejected. Critical values for this statistic can be found in tables of the Chi-Squared distribution.
<br>
<br>
'''Example 6'''
<br>
An aircraft has scheduled inspections at intervals of 20 flight hours. Table 5.4 gives the data set from the first 100 hours of flight testing.
<br>
<center>'''Table 5.4 - Grouped test data'''</center>
{|style= align="center" border="1"
!Start Time
!End Time
!Number of Failures
|-
|0|| 20|| 13
|-
|20|| 40|| 16
|-
|40|| 60|| 5
|-
|60|| 80|| 8
|-
|80|| 100|| 7
|}
<br>
:1) Estimate the parameters of the Crow-AMSAA model using maximum likelihood estimation.
<br>
:2) Evaluate the goodness-of-fit.
<br>
<br>
'''Solution'''
<br>
:1) Obtain the estimator of  <math>\beta </math>  using Eqn. (vv). Using RGA the value of  <math>\widehat{\beta }</math>  is 0.75285. Now plug this value into Eqn. (vv1) and  <math>\widehat{\lambda }</math>  is:
::<math>\widehat{\lambda }=1.52931</math>
:2) There are a total of    observed failures from  <math>d=5</math>  intervals. Table 5.5 shows that those adjacent intervals do not have to be combined after applying Eqn. (seta) to the original intervals.
 
<center>'''Table 5.5 - Observed vs. Expected Number of Failures for Grouped data'''</center>
{|style= align="center" border="1"
!Start Time
!End Time
!Observed Number of Failures
!Expected Number of Failures
|-
|0|| 20|| 13|| 14.59
|-
|20|| 40|| 16|| 9.99
|-
|40|| 60|| 5|| 8.77
|-
|60|| 80|| 8|| 8.07
|-
|80|| 100|| 7|| 7.58
|}
<br>
 
To test the model's goodness-of-fit, a Chi-Squared statistic of 5.45 is compared to the critical value of 7.8 corresponding to 3 degrees of freedom and a 0.05 significance level. Since the statistic is less than the critical value, the applicability of the Crow-AMSAA model is accepted.
 
==Estimation and Analysis with Missing Data==
Most of the reliability growth models used for estimating and tracking reliability growth based on test data assume that the data set represents all actual system failure times consistent with a uniform definition of failure (complete data). In practice, this may not always be the case and may result in too few or too many failures being reported over some interval of test time. This may result in distorted estimates of the growth rate and current system reliability. This section discusses a practical reliability growth estimation and analysis procedure based on the assumption that anomalies may exist within the data over some interval of the test period but the remaining failure data follows the Crow-AMSAA reliability growth model. In particular, it is assumed that the beginning and ending points in which the anomalies lie are generated independently of the underlying reliability growth process. The approach for estimating the parameters of the growth model with problem data over some interval of time is basically to not use this failure information. The analysis retains the contribution of the interval to the total test time, but no assumptions are made regarding the actual number of failures over the interval. This is often referred to as gap analysis.
<br>
<br>
Consider the case where a system is tested for time  <math>T</math>  and the actual failure times are recorded. The time  <math>T</math>  may possibly be an observed failure time. Also, the end points of the gap interval may or may not correspond to a recorded failure time. The underlying assumption is that the data used in the maximum likelihood estimation follows the Crow-AMSAA model with a Weibull intensity function  <math>\lambda \beta {{t}^{\beta -1}}</math> . It is not assumed that zero failures occurred during the gap interval. Rather, it is assumed that the actual number of failures is unknown, and hence no information at all regarding these failure is used to estimate  <math>\lambda </math>  and  <math>\beta </math> .
<br>
<br>
Let  <math>{{S}_{1}}</math> ,  <math>{{S}_{2}}</math>  denote the end points of the gap interval,  <math>{{S}_{1}}<{{S}_{2}}.</math>  Let  <math>0<{{X}_{1}}<{{X}_{2}}<\ldots <{{X}_{{{N}_{1}}}}\le {{S}_{1}}</math>  be the failure times over  <math>(0,\,{{S}_{1}})</math>  and let  <math>{{S}_{2}}<{{Y}_{1}}<{{Y}_{2}}<\ldots <{{Y}_{{{N}_{1}}}}\le T</math>  be the failure times over  <math>({{S}_{2}},\,T)</math> . The maximum likelihood estimates of  <math>\lambda </math>  and  <math>\beta </math>  are values  <math>\widehat{\lambda }</math>  and  <math>\widehat{\beta }</math>  satisfying the following equations.
 
::<math>\widehat{\lambda }=\frac{{{N}_{1}}+{{N}_{2}}}{S\widehat{_{1}^{\beta }}+{{T}^{\widehat{\beta }}}-S_{2}^{\widehat{\beta }}}</math>
 
::<math>\widehat{\beta }=\frac{{{N}_{1}}+{{N}_{2}}}{\widehat{\lambda }\left[ S\widehat{_{1}^{\beta }}\ln {{S}_{1}}+{{T}^{\widehat{\beta }}}\ln T-S_{2}^{\widehat{\beta }}\ln {{S}_{2}} \right]-\left[ \underset{i=1}{\overset{{{N}_{1}}}{\mathop{\sum }}}\,\ln {{X}_{i}}+\underset{i=1}{\overset{{{N}_{2}}}{\mathop{\sum }}}\,\ln {{Y}_{i}} \right]}</math>
 
In general, these equations cannot be solved explicitly for  <math>\widehat{\lambda }</math>  and  <math>\widehat{\beta }</math> , but must be solved by an iterative procedure.
<br>
<br>
'''Example 7'''
<br>
Consider a system under development that was subjected to a reliability growth test for  <math>T=1000</math>  hours. Each month, the successive failure times on a cumulative test time basis were reported. According to the test plan, 125 hours of test time were accumulated on each prototype system each month. The total reliability growth test program lasted for 7 months. One prototype was tested for each of the months 1, 3, 4, 5, 6 and 7 with 125 hours of test time. During the second month, two prototypes were tested for a total of 250 hours of test time. The next table shows the successive  <math>N=86</math>  failure times that were reported for  <math>T=1000</math>  hours of testing.
 
<center><caption><math>{{X}_{i}},</math>  <math>i=1,2,\ldots ,86</math>, <math>N = 86, T = 1000</math></caption></center>
{|style= align="center"
|-
|.5  || .6  ||10.7|| 16.6|| 18.3|| 19.2|| 19.5|| 25.3
|-
|39.2|| 39.4 ||43.2|| 44.8|| 47.4|| 65.7|| 88.1|| 97.2
|-
|104.9||105.1|| 120.8|| 195.7 ||217.1 ||219|| 257.5|| 260.4
|-
|281.3 || 283.7||289.8|| 306.6|| 328.6|| 357.0|| 371.7|| 374.7
|-
|393.2|| 403.2|| 466.5|| 500.9|| 501.5|| 518.4|| 520.7|| 522.7
|-
|524.6|| 526.9|| 527.8|| 533.6|| 536.5|| 542.6|| 543.2|| 545.0
|-
|547.4|| 554.0|| 554.1|| 554.2|| 554.8|| 556.5|| 570.6|| 571.4
|-
|574.9|| 576.8|| 578.8|| 583.4|| 584.9|| 590.6|| 596.1|| 599.1
|-
|600.1|| 602.5|| 613.9|| 616.0|| 616.2|| 617.1|| 621.4|| 622.6
|-
|624.7|| 628.8|| 642.4|| 684.8|| 731.9|| 735.1|| 753.6|| 792.5
|-
|803.7|| 805.4|| 832.5|| 836.2|| 873.2|| 975.1
|}
The observed and cumulative number of failures for each month are:
 
{|style= align="center" border="1"
!Month
!Time Period
!Observed Failure Times
!Cumulative Failure Times
|-
|1|| 0-125|| 19|| 19
|-
|2|| 125-375||13|| 32
|-
|3|| 375-500 ||3|| 35
|-
|4|| 500-625 ||38|| 73
|-
|5|| 625-750 ||5|| 78
|-
|6|| 750-875 ||7|| 85
|-
|7|| 875-1000||1|| 86
|}
 
:1) Determine the maximum likelihood estimators for the Crow-AMSAA model.
:2) Evaluate the goodness-of-fit for the model.
:3) Consider  <math>(500,\ 625)</math>  as the gap interval and determine the maximum likelihood estimates of  <math>\lambda </math>  and  <math>\beta </math> .
<br>
<br>
'''Solution'''
:1) For the time terminated test, using Eqn. (amsaa6):
::<math>\begin{align}
& \widehat{\beta }= & 0.7597 \\
& \widehat{\lambda }= & 0.4521 
\end{align}</math>
:2) The Cramér-von Mises goodness-of-fit test for this data set yields:
::<math>C_{M}^{2}=\tfrac{1}{12M}+\underset{i=1}{\overset{M}{\mathop{\sum }}}\,{{\left[ (\tfrac{{{T}_{i}}}{T})\widehat{^{\beta }}-\tfrac{2i-1}{2M} \right]}^{2}}=</math>  <math>0.6989</math>
[[Image:rga5.14.png|thumb|center|400px|Observed and estimated number of failures for the full data set.]]
<br>
[[Image:rga5.15.png|thumb|center|400px|Observed and estimated number of failures for the gap data set.]]
<br>
 
The critical value at the 10% significance level is 0.173. Therefore, the test indicated that the analyst should reject the hypothesis that the data set follows the Crow-AMSAA reliability growth model. Figure 4fig814 is a plot of  <math>\ln N(t)</math>  versus  <math>\ln t</math>  with the fitted line  <math>\ln \hat{\lambda }+\hat{\beta }\ln t</math> , where  <math>\widehat{\lambda }=0.4521</math>  and  <math>\widehat{\beta }=0.7597</math>  are the maximum likelihood estimates. Observing the data during the fourth month (between 500 and 625 hr), 38 failures were reported. This number is very high in comparison to the failures reported in the other months. A quick investigation found that a number of new data collectors were assigned to the project during this month. It was also discovered that extensive design changes were made during this period, which involved the removal of a large number of parts. It is possible that these removals, which were not failures, were incorrectly reported as failed parts. Based on knowledge of the system and the test program, it was clear that such a large number of actual system failures was extremely unlikely. The consensus was that this anomaly was due to the failure reporting. It was decided that the actual number of failures over this month would be assumed for this analysis to be unknown but consistent with the remaining data and the Crow-AMSAA reliability growth model.
<br>
:3) Considering the problem interval  <math>(500,625)</math>  as the gap interval, we will use the data over the interval  <math>(0,500)</math>  and over the interval  <math>(625,1000).</math>  Eqns. (gaplambda) and (gapbeta) are the appropriate equations to estimate  <math>\lambda </math>  and  <math>\beta </math>  since the failure times are known. In this case  <math>{{S}_{1}}=500,\,{{S}_{2}}=625</math>  and  <math>T=1000,\ {{N}_{1}}=35,\,{{N}_{2}}=13.</math>  The maximum likelihood estimates of  <math>\lambda </math>  and  <math>\beta </math>  are:
 
::<math>\begin{align}
  & \widehat{\beta }= & 0.5596 \\
& \widehat{\lambda }= & 1.1052 
\end{align}</math>
 
Figure 5.15 is a plot of the cumulative number of failures versus time. This plot is approximately linear, which also indicates a good fit of the model.
 
==Crow Discrete Reliability Growth Model==
The Crow-AMSAA model can be adapted for the analysis of success/failure data (also called "discrete" or "attribute" data).
<br>
===Model Development===
Suppose system development is represented by  <math>i</math>  configurations. This corresponds to  <math>i-1</math>  configuration changes, unless fixes are applied at the end of the test phase, in which case there would be  <math>i</math>  configuration changes. Let  <math>{{N}_{i}}</math>  be the number of trials during configuration  <math>i</math>  and let  <math>{{M}_{i}}</math>  be the number of failures during configuration  <math>i</math> . Then the cumulative number of trials through configuration  <math>i</math> , namely  <math>{{T}_{i}}</math> , is the sum of the  <math>{{N}_{i}}</math>  for all  <math>i</math> , or:
 
::<math>{{T}_{i}}=\underset{}{\overset{}{\mathop \sum }}\,{{N}_{i}}</math>
 
And the cumulative number of failures through configuration  <math>i</math> , namely  <math>{{K}_{i}}</math> , is the sum of the  <math>{{M}_{i}}</math>  for all  <math>i</math> , or:
 
::<math>{{K}_{i}}=\underset{}{\overset{}{\mathop \sum }}\,{{M}_{i}}</math>
 
The expected value of  <math>{{K}_{i}}</math>  can be expressed as  <math>E[{{K}_{i}}]</math>  and defined as the expected number of failures by the end of configuration  <math>i</math> . Applying the learning curve property to  <math>E[{{K}_{i}}]</math>  implies:
 
::<math>E\left[ {{K}_{i}} \right]=\lambda T_{i}^{\beta }</math>
 
Denote  <math>{{f}_{1}}</math>  as the probability of failure for configuration 1 and use it to develop a generalized equation for  <math>{{f}_{i}}</math>  in terms of the  <math>{{T}_{i}}</math>  and  <math>{{N}_{i}}</math> . From Eqn. (expectedn), the expected number of failures by the end of configuration 1 is:
 
::<math>E\left[ {{K}_{1}} \right]=\lambda T_{1}^{\beta }={{f}_{1}}{{N}_{1}}</math>
 
::<math>\therefore {{f}_{1}}=\frac{\lambda T_{1}^{\beta }}{{{N}_{1}}}</math>
 
Applying Eqn. (expectedn) again and noting that the expected number of failures by the end of configuration 2 is the sum of the expected number of failures in configuration 1 and the expected number of failures in configuration 2:
 
::<math>\begin{align}
  & E\left[ {{K}_{2}} \right]= & \lambda T_{2}^{\beta } \\
& = & {{f}_{1}}{{N}_{1}}+{{f}_{2}}{{N}_{2}} \\
& = & \lambda T_{1}^{\beta }+{{f}_{2}}{{N}_{2}} 
\end{align}</math>
 
::<math>\therefore {{f}_{2}}=\frac{\lambda T_{2}^{\beta }-\lambda T_{1}^{\beta }}{{{N}_{2}}}</math>
 
By this method of inductive reasoning, a generalized equation for the failure probability on a configuration basis,  <math>{{f}_{i}}</math> , is obtained, such that:
 
::<math>{{f}_{i}}=\frac{\lambda T_{i}^{\beta }-\lambda T_{i-1}^{\beta }}{{{N}_{i}}}</math>
 
For the special case where  <math>{{N}_{i}}=1</math>  for all  <math>i</math> , Eqn. (dfi) becomes a smooth curve,  <math>{{g}_{i}}</math> , that represents the probability of failure for trial by trial data, or:
 
::<math>{{g}_{i}}=\lambda \cdot {{i}^{\beta }}-\lambda \cdot {{\left( i-1 \right)}^{\beta }}</math>
 
In Eqn. (dfi1),  <math>i</math>  represents the trial number. Thus using Eqn. (dfi), an equation for the reliability (probability of success) for the  <math>{{i}^{th}}</math>  configuration is obtained:
 
::<math>{{R}_{i}}=1-{{f}_{i}}</math>
 
And using Eqn. (dfi1), the equation for the reliability for the  <math>{{i}^{th}}</math>  trial is:
 
::<math>{{R}_{i}}=1-{{g}_{i}}</math>
 
===Maximum Likelihood Estimators===
This section describes procedures for estimating the parameters of the Crow-AMSAA model for success/failure data. An example is presented illustrating these concepts. The estimation procedures described below provide maximum likelihood estimates (MLEs) for the model's two parameters,  <math>\lambda </math>  and  <math>\beta </math> . The MLEs for  <math>\lambda </math>  and  <math>\beta </math>  allow for point estimates for the probability of failure, given by:
 
::<math>{{\hat{f}}_{i}}=\frac{\hat{\lambda }T_{i}^{{\hat{\beta }}}-\hat{\lambda }T_{i-1}^{{\hat{\beta }}}}{{{N}_{i}}}=\frac{\hat{\lambda }\left( T_{i}^{{\hat{\beta }}}-T_{i-1}^{{\hat{\beta }}} \right)}{{{N}_{i}}}</math>
 
And the probability of success (reliability) for each configuration  <math>i</math>  is equal to:
 
::<math>{{\hat{R}}_{i}}=1-{{\hat{f}}_{i}}</math>
 
The likelihood function is:
<br>
::<math>\underset{i=1}{\overset{k}{\mathop \prod }}\,\left( \begin{matrix}
  {{N}_{i}}  \\
  {{M}_{i}}  \\
\end{matrix} \right){{\left( \frac{\lambda T_{i}^{\beta }-\lambda T_{i-1}^{\beta }}{{{N}_{i}}} \right)}^{{{M}_{i}}}}{{\left( \frac{{{N}_{i}}-\lambda T_{i}^{\beta }+\lambda T_{i-1}^{\beta }}{{{N}_{i}}} \right)}^{{{N}_{i}}-{{M}_{i}}}}</math>
 
Taking the natural log on both sides yields:
 
::<math>\begin{align}
  & \Lambda = & \underset{i=1}{\overset{K}{\mathop \sum }}\,\left[ \ln \left( \begin{matrix}
  {{N}_{i}}  \\
  {{M}_{i}}  \\
\end{matrix} \right)+{{M}_{i}}\left[ \ln (\lambda T_{i}^{\beta }-\lambda T_{i-1}^{\beta })-\ln {{N}_{i}} \right] \right] \\
&  & +\underset{i=1}{\overset{K}{\mathop \sum }}\,\left[ ({{N}_{i}}-{{M}_{i}})\left[ \ln ({{N}_{i}}-\lambda T_{i}^{\beta }+\lambda T_{i-1}^{\beta })-\ln {{N}_{i}} \right] \right] 
\end{align}</math>
 
Taking the derivative with respect to  <math>\lambda </math>  and  <math>\beta </math>  respectively, exact MLEs for  <math>\lambda </math>  and  <math>\beta </math>  are values satisfying the following two equations:
 
::<math>\begin{align}
  & \underset{i=1}{\overset{K}{\mathop \sum }}\,{{H}_{i}}\times {{S}_{i}}= & 0 \\
& \underset{i=1}{\overset{K}{\mathop \sum }}\,{{U}_{i}}\times {{S}_{i}}= & 0 
\end{align}</math>
 
:where:
 
::<math>\begin{align}
  & {{H}_{i}}= & \underset{i=1}{\overset{K}{\mathop \sum }}\,\left[ T_{i}^{\beta }\ln {{T}_{i}}-T_{i-1}^{\beta }\ln {{T}_{i-1}} \right] \\
& {{S}_{i}}= & \frac{{{M}_{i}}}{\left[ \lambda T_{i}^{\beta }-\lambda T_{i-1}^{\beta } \right]}-\frac{{{N}_{i}}-{{M}_{i}}}{\left[ {{N}_{i}}-\lambda T_{i}^{\beta }+\lambda T_{i-1}^{\beta } \right]} \\
& {{U}_{i}}= & T_{i}^{\beta }-T_{i-1}^{\beta }\, 
\end{align}</math>
 
'''Example 8'''
<br>
A one-shot system underwent reliability growth development testing for a total of 68 trials. Delayed corrective actions were incorporated after the 14th, 33rd and 48th trials. From trial 49 to trial 68, the configuration was not changed.
<br>
• Configuration 1 experienced 5 failures,
<br>
• Configuration 2 experienced 3 failures,
<br>
• Configuration 3 experienced 4 failures and
<br>
• Configuration 4 experienced 4 failures.
<br>
<br>
:1) Estimate the parameters of the Crow-AMSAA model using maximum likelihood estimation.
:2) Estimate the unreliability and reliability by configuration.
<br>
<br>
'''Solution'''
<br>
:1) The solution of Eqns. (solution1) and (solution2) provides for  <math>\lambda </math>  and  <math>\beta </math>  corresponding to 0.5954 and 0.7801, respectively.
:2) Table 5.6 displays the results of Eqns. (ffffi) and (rrrri).
Figures 4fig816 and 4fig817 show plots of the estimated unreliability and reliability by configuration.
<br>
<center>Table 5.6 - Estimated failure probability and reliability by configuration</center>
{|style= align="center" border="2"
!Configuration(<math>i</math>)
!Estimated Failure Probability
!Estimated Reliability
|-
|1|| 0.333|| 0.667
|-
|2|| 0.234|| 0.766
|-
|3|| 0.206|| 0.794
|-
|4|| 0.190|| 0.810
|}
<br>
[[Image:rga5.16.png|thumb|center|400px|Estimated unreliability by configuration.]]
<br>
[[Image:rga5.17.png|thumb|center|400px|Estimated reliability by configuration.]]
<br>
 
===Mixed Data===
<br>
In the RGA Software, the Discrete Data > Mixed Data option gives a data sheet that can have input data that is either configuration in groups or individual trial by trial, or a mixed combination of individual trials and configurations of more than one trial. The calculations use the same mathematical methods described in section 5.3 for the Crow-AMSAA grouped data.
<br>
'''Example 9'''
<br>
Table 5.7 shows the number of fai
<math>\widehat{\beta }=0.7950</math>
lures of each interval of trials and the cumulative number of trials in each interval for a reliability growth test. For example, the first row of Table 5.7 indicates that for an interval of 14 trials, 5 failures occurred.
<br>
{|style= align="center" border="2"
|+'''Table 5.7 - Mixed data for Example 9'''
!Failures in Interval
!Cumulative Trials
|-
|5|| 14
|-
|3|| 33
|-
|4|| 48
|-
|0|| 52
|-
|1|| 53
|-
|0|| 57
|-
|1|| 58
|-
|0|| 62
|-
|1|| 63
|-
|0|| 67
|-
|1|| 68
|}
 
<br>
Using RGA 7, the parameters of the Crow-AMSAA model are estimated as follows:
 
:and:
 
::<math>\widehat{\lambda }=0.5588</math>
 
As we have seen, the Crow-AMSAA instantaneous failure intensity,  <math>{{\lambda }_{i}}(T)</math> , is defined as:
 
::<math>{{\lambda }_{i}}(T)=\lambda \beta {{T}^{\beta -1}},\text{with }T>0,\text{ }\lambda >0\text{ and }\beta >0</math>
 
Using the above parameter estimates, we can calculate the or instantaneous unreliability at the end of the test, or  <math>T=68.</math>
 
::<math>{{R}_{i}}(68)=0.5588\cdot 0.7950\cdot {{68}^{0.7950-1}}=0.1871</math>
 
This result that can be obtained from the Quick Calculation Pad (QCP), for  <math>T=68,</math>  as seen in Figure Mixednst.FI.
<br>
[[Image:rga5.18.png|thumb|center|400px|Instantaneous unreliability at the end of the test.]]
<br>
The instantaneous reliability can then be calculated as:
 
::<math>{{R}_{inst}}=1-0.1871=0.8129</math>
 
The average unreliability is calculated as:
 
::<math>\text{Average Unreliability }({{t}_{1,}}{{t}_{2}})=\frac{\lambda t_{2}^{\beta }-\lambda t_{1}^{\beta }}{{{t}_{2}}-{{t}_{1}}}</math>
 
and the average reliability is calculated as:
 
::<math>\text{Average Reliability }({{t}_{1,}}{{t}_{2}})=1-\frac{\lambda t_{2}^{\beta }-\lambda t_{1}^{\beta }}{{{t}_{2}}-{{t}_{1}}}</math>
 
====Bounds on Average Failure Probability for Mixed Data====
The process to calculate the average unreliability confidence bounds for mixed data is as follows:
<br>
:1) Calculate the average failure probability    .
:2) There will exist a  <math>{{t}^{*}}</math>  between  <math>{{t}_{1}}</math>  and  <math>{{t}_{2}}</math>  such that the instantaneous unreliability at  <math>{{t}^{*}}</math>  equals the average unreliability    . The confidence intervals for the instantaneous unreliability at  <math>{{t}^{*}}</math>  are the confidence intervals for the average unreliability    .
<br>
<br>
====Bounds on Average Reliability for Mixed Data====
The process to calculate the average reliability confidence bounds for mixed data is as follows:
<br>
:1) Calculate confidence bounds for average unreliability    as described above.
:2) The confidence bounds for reliability are 1 minus these confidence bounds for average unreliability.
 
==Applicability==
The Duane and Crow-AMSAA models are the most frequently used reliability growth models. Their relationship comes from the fact that both make use of the underlying observed linear relationship between the logarithm of cumulative MTBF and cumulative test time. However, the Duane model does not provide a capability to test whether the change in MTBF observed over time is significantly different from what might be seen due to random error between phases. The Crow-AMSAA model allows for such assessments. Also, the Crow-AMSAA allows for development of hypothesis testing procedures to determine growth presence in the data where ( <math>\beta <1</math>  indicates that there is growth in MTBF,  <math>\beta =1</math>  indicates a constant MTBF and  <math>\beta >1</math>  indicates a decreasing MTBF). Additionally, the Crow-AMSAA model views the process of reliability growth as probabilistic, while the Duane model views the process as deterministic.
 
==Change of Slope==
The assumption of the Crow-AMSAA (NHPP) model is that the failure intensity is monotonically increasing, decreasing or remaining constant over time. However, there might be cases in which the system design or the operational environment experiences major changes during the observation period and, therefore, a single model will not be appropriate to describe the failure behavior for the entire timeline.
RGA incorporates a methodology that can be applied to scenarios where a major change occurs during a reliability growth test. The test data can be broken into two segments with a separate Crow-AMSAA (NHPP) model applied to each segment.
Consider the data in Figure changeflopeisual that were obtained during a reliability growth test.
As discussed above, the cumulative number of failures vs. the cumulative time should be linear on logarithmic scales. Figure changeflopeisualog shows the data plotted on logarithmic scales.
<br>
[[Image:rga5.19.png|thumb|center|400px|Data from a reliability growth test.]]
<br>
<br>
<br>
[[Image:rga5.20.png|thumb|center|400px|Cumulative number of failures plotted on logarithmic axes.]]
<br>
 
One can easily recognize that the failure behavior is not constant throughout the duration of the test. Just by observing the data, it can be asserted that a major change occurred at around  <math>140</math>  hours that resulted in a change in the rate of failures. Therefore, using a single model to analyze this data set likely will not be appropriate.
The Change of Slope methodology proposes to split the data into two segments and apply a Crow-AMSAA (NHPP) model to each segment. The time of change that will be used to split the data into the two segments (it will be referred to as  <math>{{T}_{1}}</math> ) could be estimated just by observing the data but will most likely be dictated by engineering knowledge of the specific change to the system design or operating conditions. It is important to note that although two separate models will be applied to each segment, the information collected in the first segment (i.e. data up to  <math>{{T}_{1}}</math> ) will be considered when creating the model for the second segment (i.e. data after  <math>{{T}_{1}}</math> ). The models presented next can be applied to the reliability growth analysis of a single system or multiple systems.
<br>
<br>
===Model for First Segment (Data up to  <math>{{T}_{1}}</math> )===
The data up to the point of the change that occurs at  <math>{{T}_{1}}</math>  will be analyzed using the Crow-AMSAA (NHPP) model. Based on Eqns. (amsaa5) and (amsaa6), the ML estimators of the model are:
 
::<math>\widehat{{{\lambda }_{1}}}=\frac{{{n}_{1}}}{T_{1}^{{{\beta }_{1}}}}</math>
 
:and
 
::<math>{{\widehat{\beta }}_{1}}=\frac{{{n}_{1}}}{{{n}_{1}}\ln {{T}_{1}}-\underset{i=1}{\overset{{{n}_{1}}}{\mathop{\sum }}}\,\ln {{t}_{i}}}</math>
 
:where:
<br>
• <math>{{T}_{1}}</math>  is the time when the change occurs.
<br>
• <math>{{n}_{1}}</math> is the number of failures observed up to time  <math>{{T}_{1}}.</math>
<br>
• <math>{{t}_{i}}</math>  is the time at which each corresponding failure was observed.
Eqn. (beta1) can be rewritten as follows:
 
::<math>\begin{align}
  & {{\widehat{\beta }}_{1}}= & \frac{{{n}_{1}}}{{{n}_{1}}\ln {{T}_{1}}-\left( \ln {{t}_{1}}+\ln {{t}_{2}}+...+\ln {{t}_{{{n}_{1}}}} \right)} \\
& = & \frac{{{n}_{1}}}{(\ln {{T}_{1}}-\ln {{t}_{1}})+(\ln {{T}_{1}}-\ln {{t}_{2}})+(...)+(\ln {{T}_{1}}-\ln {{t}_{{{n}_{1}}}})} \\
& = & \frac{{{n}_{1}}}{\ln \tfrac{{{T}_{1}}}{{{t}_{1}}}+\ln \tfrac{{{T}_{1}}}{{{t}_{2}}}+...+\ln \tfrac{{{T}_{1}}}{{{t}_{{{n}_{1}}}}}} 
\end{align}</math>
 
:or
 
::<math>{{\widehat{\beta }}_{1}}=\frac{{{n}_{1}}}{\underset{i=1}{\overset{{{n}_{1}}}{\mathop{\sum }}}\,\ln \tfrac{{{T}_{1}}}{{{t}_{i}}}}</math>
 
===Model for Second Segment (Data after  <math>{{T}_{1}}</math> )===
The Crow-AMSAA (NHPP) model will be used again to analyze the data after  <math>{{T}_{1}}</math> . However, the information collected during the first segment will be used when creating the model for the second segment. Given that, the ML estimators of the model parameters in the second segment are:
 
::<math>\widehat{{{\lambda }_{2}}}=\frac{{{n}_{2}}}{T_{2}^{{{\beta }_{2}}}}</math>
 
and similar to Eqn. (beta1mallq):
 
::<math>{{\widehat{\beta }}_{2}}=\frac{{{n}_{2}}}{{{n}_{1}}\ln \tfrac{{{T}_{2}}}{{{T}_{1}}}+\underset{i={{n}_{1}}+1}{\overset{n}{\mathop{\sum }}}\,\ln \tfrac{{{T}_{2}}}{{{t}_{i}}}}</math>
 
:where:
 
<br>
• <math>{{n}_{2}}</math>  is the number of failures that were observed after  <math>{{T}_{1}}</math> .
<br>
• <math>n={{n}_{1}}+{{n}_{2}}</math>  is the total number of failures observed throughout the test.
<br>
• <math>{{T}_{2}}</math>  is the end time of the test. The test can either be failure terminated or time terminated.
<br>
<br>
===Example 10===
<br>
<center><span style="color:blue">Table 5.8 - Failure times from a reliability growth test</span></center>
<center><math>\begin{matrix}
  \text{7}\text{.8} & \text{99}\text{.2} & \text{151} & \text{260}\text{.1} & \text{342} & \text{430}\text{.2}  \\
  \text{17}\text{.6} & \text{99}\text{.6} & \text{163} & \text{273}\text{.1} & \text{350}\text{.2} & \text{445}\text{.7}  \\
  \text{25}\text{.3} & \text{100}\text{.3} & \text{174}\text{.5} & \text{274}\text{.7} & \text{355}\text{.2} & \text{475}\text{.9}  \\
  \text{15} & \text{102}\text{.5} & \text{177}\text{.4} & \text{282}\text{.8} & \text{364}\text{.6} & \text{490}\text{.1}  \\
  \text{47}\text{.5} & \text{112} & \text{191}\text{.6} & \text{285} & \text{364}\text{.9} & \text{535}  \\
  \text{54} & \text{112}\text{.2} & \text{192}\text{.7} & \text{315}\text{.4} & \text{366}\text{.3} & \text{580}\text{.3}  \\
  \text{54}\text{.5} & \text{120}\text{.9} & \text{213} & \text{317}\text{.1} & \text{379}\text{.4} & \text{610}\text{.6}  \\
  \text{56}\text{.4} & \text{121}\text{.9} & \text{244}\text{.8} & \text{320}\text{.6} & \text{389} & \text{640}\text{.5}  \\
  \text{63}\text{.6} & \text{125}\text{.5} & \text{249} & \text{324}\text{.5} & \text{394}\text{.9} & {}  \\
  \text{72}\text{.2} & \text{133}\text{.4} & \text{250}\text{.8} & \text{324}\text{.9} & \text{395}\text{.2} & {}  \\
\end{matrix}</math></center>
 
The test has a duration of 660 hours.
First, apply a single Crow-AMSAA (NHPP) model to all of the data. Figure Changeflopeingleodel shows the expected failures obtained from the model (the line) along with the observed failures (the points).
<br>
[[Image:rga5.21.png|thumb|center|400px|Analysis of the entire data set with a single Crow-AMSAA(NHPP) model.]]
<br>
[[Image:rga5.22.png|thumb|center|400px|Single Crow-AMSAA(NHPP) calculated parameters and statistical test results.]]
<br>
[[Image:rga5.23.png|thumb|center|400px|Specifying a breakpoint foor a Change of Slope Crow-AMSAA(NHPP) analysis in RGA 7.]]
<br>
As it can be seen from the plot, the model does not seem to accurately track the data. This is confirmed by performing the Cramér-von Mises goodness-of-fit test which checks the hypothesis that the data follows a non-homogeneous Poisson process with a power law failure intensity. The model fails the goodness-of-fit test because the test statistic (0.3309) is higher than the critical value (0.1729) at the 0.1 significance level. Figure Changeflopeingleodelesults shows a customized report that displays both the calculated parameters and the statistical test results.
 
Through further investigation, it is discovered that a significant design change occurred at 400 hours of test time. It is suspected that this modification is responsible for the change in the failure behavior.
<br>
 
In RGA 7 you have the option to perform a standard Crow-AMSAA (NHPP) analysis or to apply the Change of Slope, where you can specify a specific breakpoint, as shown in Figure changeflopereakoint. RGA 7 actually creates a grouped data set where the data in Segment 1 is included and defined by a single interval to calculate the Segment 2 parameters. However, these results are equivalent to the parameters estimated using the equations presented here.
 
Therefore, the Change of Slope methodology is applied to break the data into two segments for analysis. The first segment is set from 0 to 400 hours and the second segment is from 401 to 660 hours (which is the end time of the test). Based on Eqns. (lambda1) and (beta1mallq), the Crow-AMSAA (NHPP) parameters for the first segment (0-400 hours) are:
 
::<math>\widehat{{{\lambda }_{1}}}=\frac{{{n}_{1}}}{T_{1}^{{{\beta }_{1}}}}=\frac{50}{{{400}^{1.0359}}}=0.1008</math>
 
:and
 
::<math>{{\widehat{\beta }}_{1}}=\frac{{{n}_{1}}}{\underset{i=1}{\overset{{{n}_{1}}}{\mathop{\sum }}}\,\ln \tfrac{{{T}_{1}}}{{{t}_{i}}}}=\frac{50}{\underset{i=1}{\overset{50}{\mathop{\sum }}}\,\ln \tfrac{400}{{{t}_{i}}}}=1.0359</math>
 
Based on Eqns. (lambda2) and (beta2mallq), the Crow-AMSAA (NHPP) parameters for the second segment (401-660 hours) are:
 
::<math>\widehat{{{\lambda }_{2}}}=\frac{{{n}_{2}}}{T_{2}^{{{\beta }_{2}}}}=\frac{58}{{{660}^{0.2971}}}=8.4304</math>
 
::<math>{{\widehat{\beta }}_{2}}=\frac{{{n}_{2}}}{{{n}_{1}}\ln \tfrac{{{T}_{2}}}{{{T}_{1}}}+\underset{i={{n}_{1}}+1}{\overset{n}{\mathop{\sum }}}\,\ln \tfrac{{{T}_{2}}}{{{t}_{i}}}}=\frac{8}{50\ln \tfrac{660}{400}+\underset{i=51}{\overset{58}{\mathop{\sum }}}\,\ln \tfrac{660}{{{T}_{i}}}}=0.2971</math>
 
Figure changeflopelot shows a plot of the two-segment analysis along with the observed data. It is obvious that the "Change of Slope" method tracks the data more accurately.
 
This can also be verified by performing a Chi-Squared goodness-of-fit test. The Chi-Squared statistic is 1.2956, which is lower than the critical value of 12.017 at the 0.1 significance level; therefore, the analysis passes the test. Figure Changeflopereakodelesults shows a customized report that displays both the calculated parameters and the statistical test results.
 
<br>
[[Image:rga5.24.png|thumb|center|400px|Change of Slope methodology with two Crow-AMSAA(NHPP) models.]]
<br>
[[Image:rga5.25.png|thumb|center|400px|Crow-AMSAA(NHPP) Change of Slope calculated parameters and statistical test results.]]
<br>
When you have a model that fits the data, it can be used to make accurate predictions and calculations. Metrics such as the demonstrated MTBF at the end of the test or the expected number of failures at later times can be calculated. For example, Figure changeflopeTBF shows the instantaneous MTBF vs. time, together with the two-sided 90% confidence bounds. Note that confidence bounds are available for the second segment only. For times up to 400 hours, the parameters of the first segment were used to calculate the MTBF; while the parameters of the second segment were used for times after 400 hours. Also note that the number of failures at the end of segment 1 is not assumed to be equal to the number of failures at the start of segment 2. This can result in a visible jump in the plot, as in this example.
<br>
<br>
[[Image:rga5.26.png|thumb|center|400px|Instantaneous MTBF with 90% two-sided confidence bounds for the Crow-AMSAA(NHPP) model with Change of Slope.]]
<br>
Figure ChangeflopeCP shows the use of the Quick Calculation Pad (QCP) in RGA 7 to calculate the Demonstrated MTBF at the end of the test (instantaneous MTBF at time = 660), together with the two-sided 90% confidence bounds. All the calculations were based on the parameters of the second segment.
 
==General Examples==
===Example 11===
Six systems were subjected to a reliability growth test and a total of 81 failures were observed. Table 5.9 presents the start and end times, along with the times-to-failure for each system. Do the following:
<br>
:1) Estimate the parameters of the Crow-AMSAA model using maximum likelihood estimation.
:2) How many additional failures would be generated if testing continues until 3000 hours?
<br>
<br>
[[Image:rga5.27.png|thumb|center|400px|Calculation of the Demonstrated MTBF (Instantaneous MTBF at time 660).]]
<br>
<br>
{|style= align="center" border="1"
|+<span style="color:blue">Table 5.9 - Multiple systems (concurrent operating times) data for Example 11</span>
|System|| 1|| 2|| 3|| 4|| 5|| 6
|-
|Start Time|| 0|| 0|| 0|| 0|| 0|| 0
|-
|End Time|| 504|| 541|| 454|| 474|| 436|| 500
|-
|Times-to-Failure|| 21|| 83|| 26|| 36|| 23|| 7
|-
| || 29|| 83|| 26|| 306|| 46|| 13
|-
| || 43|| 83|| 57|| 306|| 127|| 13
|-
| || 43|| 169|| 64|| 334|| 166|| 31
|-
| || 43|| 213|| 169|| 354|| 169|| 31
|-
| || 66|| 299|| 213|| 395|| 213|| 82
|-
| || 115|| 375|| 231|| 403|| 213|| 109
|-
| || 159|| 431|| 231|| 448|| 255|| 137
|-
| || 199|| || 231|| 456|| 369|| 166
|-
| || 202|| || 231|| 461|| 374|| 200
|-
| || 222|| || 304|| || 380|| 210
|-
| || 248|| || 383|| || 415|| 220
|-
| || 248|| || || || || 422
|-
| || 255|| || || || || 437
|-
| || 286|| || || || || 469
|-
| || 286|| || || || || 469
|-
| || 304
|-
| || 320
|-
| || 348
|-
| || 364
|-
| || 404
|-
| || 410
|-
| || 429
|}
 
====Solution to Example 11====
:1) Figure ex9a shows the parameters estimated using RGA.
:2) The number of failures can be estimated using the Quick Calculation Pad as shown in Figure ex9b. The estimated number of failures at 3000 hours is equal to  <math>83.2451</math>  and 81 failures were observed during testing. Therefore, the number of additional failures generated if testing continues until 3000 hours is equal to  <math>83.2451-81=2.2451\approx 3</math> .
 
<math></math>
[[Image:rga5.28.png|thumb|center|400px|Estimated parameters of the Crow-AMSAA model.]]
<br>
<br>
<br>
[[Image:rga5.29.png|thumb|center|400px|Expected number of failures at 3000 hours.]]
<br>
 
===Example 12===
A prototype of a system was tested at the end of one of its design stages. The test was run for a total of 300 hours and 27 failures were observed. Table 5.10 shows the collected data set. The prototype has a design specification of an MTBF equal to 10 hours with a 90% confidence level at 300 hours. Do the following:
:1) Estimate the parameters of the Crow-AMSAA model using maximum likelihood estimation.
:2) Does the prototype meet the specified goal?
 
<center><span style="color:blue">Table 5.10 - Failure times data for Example 12</span></center>
{|style= align="center" border="1"
|-
|2.6|| 56.5|| 98.1|| 190.7
|-
|16.5|| 63.1|| 101.1|| 193
|-
|16.5|| 70.6|| 132|| 198.7
|-
|17|| 73|| 142.2|| 251.9
|-
|21.4|| 77.7|| 147.7|| 282.5
|-
|29.1|| 93.9|| 149|| 286.1
|-
|33.3|| 95.5|| 167.2
|}
 
====Solution to Example 12====
<br>
:1) Figure ex10a shows the parameters estimated using RGA.
:2) The instantaneous MTBF with one-sided 90% confidence bounds can be calculated using the <br>
Quick Calculation Pad (QCP) as shown in Figure ex10b. From the QCP, it is estimated that the lower limit on the MTBF at 300 hours with a 90% confidence level is equal to 10.8170 hours. Therefore, the prototype has met the specified goal.
<math></math>
[[Image:rga5.30.png|thumb|center|300px|Estimated parameters of the Crow-AMSAA model.]]
<br>
[[Image:rga5.31.png|thumb|center|300px|Instantaneous MTBF with one-sided 90% confidence bounds.]]
<br>
<br>
 
===Example 13===
A one-shot system underwent reliability growth development for a total of 50 trials. The test was performed as a combination of configuration in groups and individual trial by trial. Table 5.11 shows the obtained test data set. The first column specifies the number of failures that occurred in each interval and the second column the cumulative number of trials in that interval. Do the following:
<br>
:1) Estimate the parameters of the Crow-AMSAA model using maximum likelihood estimators.
:2) What are the instantaneous reliability and the 2-sided 90% confidence bounds at the end of the test?
:3) Plot the cumulative reliability with 2-sided 90% confidence bounds.
:4) If the test was continued for another 25 trials what would the expected number of additional failures be?
<br>
<br>
<center><span style="color:blue">Table 5.11 - Mixed data for Example 13</span></center>
{|style= align="center" border="1"
!Failures in Interval
!Cumulative Trials
!Failures in Interval
!Cumulative Trials
|-
|3|| 4|| 1|| 25
|-
|0|| 5|| 1|| 28
|-
|4|| 9|| 0|| 32
|-
|1|| 12|| 2|| 37
|-
|0|| 13|| 0|| 39
|-
|1|| 15|| 1|| 40
|-
|2|| 19|| 1|| 44
|-
|1|| 20|| 0|| 46
|-
|1|| 22|| 1|| 49
|-
|0|| 24|| 0|| 50
|}
 
====Solution to Example 13====
<br>
:1) Figure Mixedolio shows the parameters estimated using RGA.
 
[[Image:rga5.32.png|thumb|center|400px|Estimated parameters of the Crow-AMSAA model.]]
<br>
 
:2) Figure MixedCP shows the calculation of the instantaneous reliability with the 2-sided 90% confidence bounds. From the QCP it is estimated that the instantaneous reliability at stage 50 (or at the end of the test) is 72.6971% with an upper and lower 2-sided 90% confidence bound of 82.3627% and 39.5926% respectively.
 
[[Image:rga5.33.png|thumb|center|300px|Instantaneous reliability with 2-sided 90% confidence bounds.]]
<br>
 
:3) Figure Mixedeliabilitylot shows the plot of the cumulative reliability with the 2-sided 90% confidence bounds.
 
[[Image:rga5.34.png|thumb|center|300px|Plot of cumulative reliability with 2-sided 90% confidence bounds.]]
<br>
 
:4) Figure MixedCPumFailures shows the calculation of the expected number of failures after 75 trials. From the QCP it is estimated that the cumulative number of failures after 75 trials is  <math>26.3770\approx 27</math> . Since 20 failures occurred in the first 50 trials, the estimated number of additional failures is 7.
<br>
[[Image:rga5.35.png|thumb|center|300px|Cumulative number of failures after 75 trials.]]
<br>

Revision as of 20:47, 5 January 2012

New format available! This reference is now available in a new format that offers faster page load, improved display for calculations and images, more targeted search and the latest content available as a PDF. As of September 2023, this Reliawiki page will not continue to be updated. Please update all links and bookmarks to the latest reference at help.reliasoft.com/reference/reliability_growth_and_repairable_system_analysis

Chapter 5: Crow-AMSAA (NHPP)


RGAbox.png

Chapter 5  
Crow-AMSAA (NHPP)  

Synthesis-icon.png

Available Software:
RGA

Examples icon.png

More Resources:
RGA examples


New format available! This reference is now available in a new format that offers faster page load, improved display for calculations and images, more targeted search and the latest content available as a PDF. As of September 2023, this Reliawiki page will not continue to be updated. Please update all links and bookmarks to the latest reference at help.reliasoft.com/reference/reliability_growth_and_repairable_system_analysis

Chapter 5: Crow-AMSAA (NHPP)


RGAbox.png

Chapter 5  
Crow-AMSAA (NHPP)  

Synthesis-icon.png

Available Software:
RGA

Examples icon.png

More Resources:
RGA examples


Template loop detected: Template:Crow-amsaa(nhpp)

Retrieved from "https://www.reliawiki.com/index.php?title=Crow-AMSAA_(NHPP)&oldid=11365"