Availability Analysis Reference Example: Difference between revisions
Jump to navigation
Jump to search
Kate Racaza (talk | contribs) (Created page with '{{Reference Example|{{Banner BlockSim Reference Examples}}}} This example validates the results for availability analysis BlockSim. {{Reference_Example_Heading1}} The data se…') |
Kate Racaza (talk | contribs) No edit summary |
||
| Line 10: | Line 10: | ||
{{Reference_Example_Heading2}} | {{Reference_Example_Heading2}} | ||
A two component system’s point and interval availability for a 10 hour mission and the steady-state availability for both series and parallel configurations are calculated. The components share the same failure rate and repair rate distributions. The failure and repair rates both follow exponential distributions with a failure rate of 0.1 failures per hour and a repair rate of 0.2 repairs per hour. | A two-component system’s point and interval availability for a 10 hour mission and the steady-state availability for both series and parallel configurations are calculated. The components share the same failure rate and repair rate distributions. The failure and repair rates both follow exponential distributions with a failure rate of 0.1 failures per hour and a repair rate of 0.2 repairs per hour. | ||
{| {{Table}} | {| {{Table}} | ||
| Line 27: | Line 27: | ||
The point availability is formulated in Equation 11.12 on page 257 in the reference book as: | The point availability is formulated in Equation 11.12 on page 257 in the reference book as: | ||
::<math>P_{1}(t) = \frac{r}{\lambda + r} + \frac{\lambda}{\lambda + r}e^{-(\lambda+r) | ::<math>P_{1}(t) = \frac{r}{\lambda + r} + \frac{\lambda}{\lambda + r}e^{-(\lambda+r)t}\,\!</math> | ||
| Line 35: | Line 35: | ||
The system availability for n independent components in series, each having a component availability of <math> A_{s}(t)\,\!</math>, is given Equation 11.15 on page 259 in the reference book as: | The system availability for ''n'' independent components in series, each having a component availability of <math> A_{s}(t)\,\!</math>, is given in Equation 11.15 on page 259 in the reference book as: | ||
::<math>A_{s}(t) = \prod _{i | ::<math>A_{s}(t) = \prod _{i=1}^{n}A_{i}(t)\,\!</math> | ||
The system availability for ''n'' independent components in parallel, each having a component availability of <math> A_{s}(t)\,\!</math>, is given Equation 11.16 on page 259 in the reference book as: | The system availability for ''n'' independent components in parallel, each having a component availability of <math> A_{s}(t)\,\!</math>, is given in Equation 11.16 on page 259 in the reference book as: | ||
::<math>A_{s}(t) = 1- \prod _{i | ::<math>A_{s}(t) = 1- \prod _{i=1}^{n}(1-A_{i}(t))\,\!</math> | ||
Plugging in the numbers to the given equations, point and interval availability for a 10 hour mission and steady-state availability are calculated | Plugging in the numbers to the given equations, the point and interval availability for a 10 hour mission, and steady-state availability are calculated below. | ||
For series configuration: | For a series configuration: | ||
::<math>\begin{align} | ::<math>\begin{align} | ||
A_{s}(10) | A_{s}(10) = (0.684)^{2} = 0.468\\ | ||
A_{s,0-10} | A_{s,0-10} = (0.772)^{2} = 0.596\\ | ||
A_{s} | A_{s} = (0.667)^{2} = 0.445\\ | ||
\end{align}\,\!</math> | \end{align}\,\!</math> | ||
And for parallel configuration: | And for a parallel configuration: | ||
::<math>\begin{align} | ::<math>\begin{align} | ||
A_{s}(10) | A_{s}(10) = 1- (1- 0.684)^{2} = 0.900\\ | ||
A_{s,0-10} | A_{s,0-10} = 1- (1- 0.772)^{2} = 0.948\\ | ||
A_{s} | A_{s} = 1- (1- 0.667)^{2} = 0.889\\ | ||
\end{align}\,\!</math> | \end{align}\,\!</math> | ||
{{Reference_Example_Heading4|BlockSim}} | |||
<!-- | |||
In BlockSim, the system RBDs are configured as shown below for series and parallel configurations. Since this is an availability example, we will validate the results via simulation. | |||
[[Image:availability_rbd.png|center]] | |||
Each component is modeled using a 1-parameter exponential distribution with the given lambda (failure rate) values. They also share a corrective task that is modeled again with 1-parameter exponential distribution with the given lambda (repair rate) values. In this example, we are assuming that the component is fixed upon item failure to as good as new condition. One important point to keep in mind is that the component that is not failed still accumulates time while the corrective task is taking place for the component that failed. The reference book follows this assumption while driving the equations given above. | |||
[[Image:availability_properties.png|center]] | |||
The same simulation setup is used for both series and parallel configurations. While estimating the point and interval availability for a 10 hour mission, the simulation end time is used as 10 hours. 1000 hours is used for the simulation end time while estimating the steady-state availability since the system is assumed to reach steady state at that time. Simulation setups of the series configuration for each case are given as examples below. | |||
[[Image:availability_sim.png|center]] | |||
The results of the BlockSim simulations for each configuration are given below. The numbers match with the results calculated in the reference book. | |||
For series configuration: | |||
::<math>\begin{align} | |||
A_{s}(10) &= 0.468\\ | |||
A_{s,0-10} &= 0.6019\\ | |||
A_{s} &= 0.4459\\ | |||
\end{align}\,\!</math> | |||
{{ | And for parallel configuration: | ||
::<math>\begin{align} | |||
A_{s}(10) &= 0.9000\\ | |||
A_{s,0-10} &= 0.9419\\ | |||
A_{s} &= 0.8893\\ | |||
\end{align}\,\!</math> | |||
--> | |||
Revision as of 20:34, 3 August 2015
 |
New format available! This reference is now available in a new format that offers faster page load, improved display for calculations and images and more targeted search.
As of January 2024, this Reliawiki page will not continue to be updated. Please update all links and bookmarks to the latest references at BlockSim examples and BlockSim reference examples.