|
|
| (2 intermediate revisions by the same user not shown) |
| Line 1: |
Line 1: |
| {{Allexamplesindex}} __NOTOC__ | | {{Banner BlockSim Examples}} |
| | |
| | |
| ==Reference Examples==
| |
| *[[BlockSim_Reference_Examples|BlockSim Reference Examples]] (demonstrate how BlockSim solves a variety of problems from published references)
| |
| | |
| | |
| ==Examples==
| |
| ===Analytical Diagrams and Optimization===
| |
| * Reliability Analysis of a Storage Cluster System
| |
| * Optimized Reliability Allocation
| |
| *[http://www.reliasoft.com/BlockSim/examples/rc4/index.htm Using RBDs for Modeling Failure Modes]
| |
| *[[BlockSim_Analytical_Fault_Tree_and_RBD_Plot_Examples| Analytical Diagram Plots]]
| |
| *[[BlockSim_Allocation_Analysis_Example| Allocation Analysis]]
| |
| *[[Time-Dependent System Reliability for Components in Series]]
| |
| *[[Time-Dependent System Reliability for Components in Parallel]]
| |
| *[[Example_Using_a_Distribution_to_Approximate_the_CDF|Using a Distribution to Approximate the System cdf]]
| |
| *[[Example Calculating System Reliability with Duty Cycles|Calculating System Reliability with Duty Cycles]]
| |
| *[[Load Sharing Configuration Example|Load Sharing Configuration Example - Failure Modes Analysis]]
| |
| *[[Standby Configuration Example|Standby Configuration Example - Car Tires]]
| |
| *[[Reliability_Importance_Example|Reliability Importance Plot Example]]
| |
| | |
| ===Fault Tree Diagrams===
| |
| *Simple Examples for Fault Tree Gates
| |
| **[[AND Gate Example]]
| |
| **[[OR Gate Example]]
| |
| **[[Voting OR Gate Example]]
| |
| **[[Example_Using_Load_Sharing_Gates_in_Fault_Trees|Load Sharing Gate Example]]
| |
| **[[Standby Gate Example]]
| |
| *[[Same Example Modeled with RBDs or Fault Trees|Same Example Modeled with RBDs or Fault Trees (Modeling Failure Modes)]]
| |
| **[http://www.reliasoft.com/BlockSim/examples/rc6/index.htm Using Fault Trees for Modeling Failure Modes]
| |
| | |
| ===Simulation Diagrams===
| |
| *[http://www.reliasoft.com/BlockSim/examples/rc5/index.htm RAM Analysis for Remote Telecommunications System]
| |
| *[http://www.reliasoft.com/BlockSim/examples/rc3/index.htm Effect of Inspection Intervals]
| |
| *[[BlockSim_Example:_CM_Triggered_by_Subsystem_Down|Corrective Maintenance Triggered by Failure of a Subsystem]]
| |
| *[[Life Cycle Cost Analysis Example]]
| |
| | |
| ===Phase Diagrams===
| |
| *[[BlockSim_Example:_Aircraft_Phases_with_Forced_Landing|Aircraft Phases with Forced Landing]]
| |
| *[[BlockSim_Phase_Simulation_Plot_Examples|Oil Refinery Phase Diagram Simulation]]
| |
| *[[Example Using Success Failure Paths in Phase Diagrams|Using Success/Failure Paths in Phase Diagrams]]
| |
| *[[Example Using Subdiagram Phase Blocks|Using Subdiagram Phase Blocks]]
| |
| *[[Interval Maintenance Threshold Example|Using an Interval Maintenance Threshold in a Maintenance Phase]]
| |
| *[[Phase Throughput Examples]]
| |
| | |
| ===State Change Triggers (SCTs)===
| |
| *[[Example Using SCT for Standby Rotation|Using State Change Triggers for Standby Rotation]]
| |
| *[[Example_Using_SCT_to_Analyze_Tire_Maintenance|Using State Change Triggers to Analyze Tire Maintenance]]
| |
| *[[Example_Using_SCT_to_Analyze_Standby_with_Delay|Using State Change Triggers to Model Standby with Delay]]
| |
| *[[Example_Using_SCT_to_Model_Two_Standby_Blocks|Using State Change Triggers to Model Two Standby Devices]]
| |
| *[[Example_Demonstrating_the_State_Upon_Repair_Option_for_SCT|SCT: The State Upon Repair Option]]
| |
| *[[BlockSim_Example:_Default_OFF_unless_SCT_Overridden|Demonstrating the "Default OFF unless SCT overridden" option]]
| |
| *[[BlockSim_Example:_Default_ON_unless_SCT_Overridden|Demonstrating the "Default ON unless SCT overridden" option]]
| |
| | |
| ===Throughput Analysis===
| |
| *[[Simple_Throughput_Analysis_Example|Simple Throughput Analysis Example]]
| |
| | |
| ===Utilities===
| |
| *[[Overlay_Plot_Example|Overlay Plots]]
| |
| *[[Optimum Replacement Time Example]]
| |
| *[[BlockSim_Analytical_FRED_Report_Example| Analytical FRED Report]]
| |
