Example Using SCT for Standby Rotation

New format available! This reference is now available in a new format that offers faster page load, improved display for calculations and images and more targeted search.

As of January 2024, this Reliawiki page will not continue to be updated. Please update all links and bookmarks to the latest references at BlockSim examples and BlockSim reference examples.

---

This example also appears in the System analysis reference.

This example illustrates the use of state change triggers in BlockSim (Version 8 and above) by using a simple standby configuration. Note that this example could also be done using the standby container functionality in BlockSim.

More specifically, the following settings are illustrated:

1. State Upon Repair: Default OFF unless SCT overridden
2. Activate a block if any item from these associated maintenance group(s) goes down
   

Problem Statement

Assume three devices A, B and C in a standby redundancy (or only one unit is needed for system operation). The system begins with device A working. When device A fails, B is turned on and repair actions are initiated on A. When B fails, C is turned on and so forth.

BlockSim Solution

The BlockSim model of this system is shown in the figure below.

• The failure distributions of all three blocks follow a Weibull distribution with Beta = 1.5 and Eta = 1,000 hours.
• The repair distributions of the three blocks follow a Weibull distribution with Beta = 1.5 and Eta = 100 hours.
• After repair, the blocks are "as good as new."

There are three maintenance groups, 2_A, 2_B and 2_C, set as follows:

• Block A belongs to maintenance group 2_A.
  • It has a state change trigger.
    • The initial state is ON and the state upon repair is "Default OFF unless SCT overridden."
    • If any item from maintenance group 2_C goes down, then activate this block.

• Block B belongs to maintenance group 2_B.
  • It has a state change trigger.
    • The initial state is OFF and the state upon repair is "Default OFF unless SCT overridden."
    • If any item from maintenance group 2_A goes down, then activate this block.

• Block C belongs to maintenance group 2_C.
  • It has a state change trigger.
    • The initial state is OFF and the state upon repair is "Default OFF unless SCT overridden."
    • If any item from maintenance group 2_B goes down, then activate this block.

• All blocks A, B and C are as good as new after repair.

System Events

The system event log for a single run through the simulation algorithm is shown in the Block Up/Down plot below, and is as follows:

1. At 73 hours, Block A fails and activates Block B.
2. At 183 hours, Block B fails and activates Block C.
3. At 215 hours, Block B is done with repair. At this time, Block C is operating, so according to the settings, Block B is standby.
4. At 238 hours, Block A is done with repair. At this time, Block C is operating. Thus Block A is standby.
5. At 349 hours, Block C fails and activates Block A.
6. At 396 hours, Block A fails and activates Block B.
7. At 398 hours, Block C is done with repair. At this time, Block B is operating. Thus Block C is standby.
8. At 432 hours, Block A is done with repair. At this time, Block B is operating. Thus Block A is standby.
9. At 506 hours, Block B fails and activates Block C.
10. At 515 hours, Block B is done with repair and stays standby because Block C is operating.
11. At 536 hours, Block C fails and activates Block A.
12. At 560 hours, Block A fails and activates Block B.
13. At 575 hours, Block B fails and makes a request to activate Block C. However, Block C is under repair at the time. Thus when Block C is done with repair at 606 hours, the OFF setting is overridden and it is operating immediately.
14. At 661 hours, Block C fails and makes a request to activate Block A. However, Block A is under repair at the time. Thus when Block A is done with repair at 699 hours, the OFF setting is overridden and it is operating immediately.
15. Block B and Block C are done with repair at 682 hours and at 746 hours respectively. However, at these two time points, Block A is operating. Thus they are both standby upon repair according to the settings.