Duane Model

In 1962, J. T. Duane published a report in which he presented failure data of different systems during their development programs [8]. While analyzing the data, it was observed that the cumulative MTBF versus cumulative operating time followed a straight line when plotted on log-log paper, as shown next.

Based on that observation, Duane developed his model as follows. If [math]\displaystyle{ N(T)\,\! }[/math] is the number of failures by time [math]\displaystyle{ T\,\! }[/math], the observed mean (average) time between failures, [math]\displaystyle{ MTB{{F}_{c}},\,\! }[/math] at time [math]\displaystyle{ T\,\! }[/math] is:

[math]\displaystyle{ MTB{{F}_{c}}=\frac{T}{N(T)}\,\! }[/math]

The equation of the line can be expressed as:

[math]\displaystyle{ \begin{align} y=mx+c \end{align}\,\! }[/math]

Setting:

[math]\displaystyle{ \begin{align} y= & \ln (MTB{{F}_{c}}) \\ x= & \ln (T) \\ m= & \alpha \\ c= & \ln b \end{align}\,\! }[/math]

yields:

[math]\displaystyle{ \begin{align} \ln (MTB{{F}_{c}})=\alpha \ln (T)+\ln b \end{align}\,\! }[/math]

Then equating [math]\displaystyle{ MTB{{F}_{c}}\,\! }[/math] to its expected value, and assuming an exact linear relationship, gives:

[math]\displaystyle{ \begin{align} E(MTB{{F}_{c}})=b{{T}^{\alpha }} \end{align}\,\! }[/math]

or:

[math]\displaystyle{ \begin{align} MTB{{F}_{c}}=b{{T}^{\alpha }} \end{align}\,\! }[/math]

And, if you assume a constant failure intensity, then the cumulative failure intensity, [math]\displaystyle{ {{\lambda }_{c}}\,\! }[/math], is:

[math]\displaystyle{ E({{\lambda }_{c}})=\frac{1}{b}{{T}^{-\alpha }}\,\! }[/math]

or:

[math]\displaystyle{ {{\hat{{\bar{\lambda }}}}_{c}}=\frac{1}{b}{{T}^{-\alpha }}\,\! }[/math]

Also, the expected number of failures up to time [math]\displaystyle{ T\,\! }[/math] is:

[math]\displaystyle{ \begin{align} E(N(T))= & {{\hat{{\bar{\lambda }}}}_{c}}\cdot T \\ = & \frac{1}{b}{{T}^{1-\alpha }} \end{align}\,\! }[/math]

where:

• [math]\displaystyle{ {{\hat{{\bar{\lambda }}}}_{c}}\,\! }[/math] is the average estimate of the cumulative failure intensity, failures/hour.
• [math]\displaystyle{ T\,\! }[/math] is the total accumulated unit hours of test and/or development time.
• [math]\displaystyle{ 1/b\,\! }[/math] is the cumulative failure intensity at [math]\displaystyle{ T = 1\,\! }[/math] or at the beginning of the test, or the earliest time at which the first [math]\displaystyle{ {{\hat{{\bar{\lambda }}}}}\,\! }[/math] is predicted, or the [math]\displaystyle{ {{\hat{{\bar{\lambda }}}}}\,\! }[/math] for the equipment at the start of the design and development process.
• [math]\displaystyle{ \alpha\,\! }[/math]is the improvement rate in the [math]\displaystyle{ {{\hat{{\bar{\lambda }}}}}, 0\le \alpha \le 1\,\! }[/math].

The corresponding [math]\displaystyle{ MTB{{F}_{c}}\,\! }[/math], or [math]\displaystyle{ {{\hat{m}}_{c}}\,\! }[/math], is equal to:

[math]\displaystyle{ {{\hat{m}}_{c}}=b{{T}^{\alpha }}\,\! }[/math]

where [math]\displaystyle{ b=\,\! }[/math] cumulative MTBF at [math]\displaystyle{ T=1\,\! }[/math] or at the beginning of the test, or the earliest time at which the first [math]\displaystyle{ \hat{m}\,\! }[/math] can be determined, or the [math]\displaystyle{ \hat{m}\,\! }[/math] predicted at the start of the design and development process ( [math]\displaystyle{ b\gt 0\,\! }[/math] ).

The cumulative MTBF, [math]\displaystyle{ {{\hat{m}}_{c}}\,\! }[/math], and [math]\displaystyle{ {{\hat{{\bar{\lambda }}}}_{c}}\,\! }[/math] tell whether [math]\displaystyle{ m\,\! }[/math] is increasing or [math]\displaystyle{ \lambda \,\! }[/math] is decreasing with time, utilizing all data up to that time. You may want to know, however, the instantaneous [math]\displaystyle{ {{\hat{m}}_{i}}\,\! }[/math] or [math]\displaystyle{ {{\hat{{\bar{\lambda }}}}_{i}}\,\! }[/math] to see what you are doing at a specific instant or after a specific test and development time. The instantaneous failure intensity, [math]\displaystyle{ {{\lambda }_{i}}\,\! }[/math], is:

[math]\displaystyle{ \begin{align} {{\lambda }_{i}}= & \frac{d(E(N(T)))}{dT} \\ = & \frac{1}{b}(1-\alpha ){{T}^{-\alpha }} \\ = & (1-\alpha ){{\lambda }_{c}} \end{align}\,\! }[/math]

Similarly, using the equation for the expected number of failures up to time [math]\displaystyle{ T\,\! }[/math], this procedure yields:

[math]\displaystyle{ \begin{align} {{m}_{i}}= & \frac{1}{1-\alpha }b{{T}^{\alpha }} \\ = & \frac{1}{1-\alpha }{{{\hat{m}}}_{c}},:\ \ \alpha \not{=}1 \end{align}\,\! }[/math]

where [math]\displaystyle{ \alpha =1\,\! }[/math] implies infinite MTBF growth.

As shown in these derivations, the instantaneous failure intensity improvement line is obtained by shifting the cumulative failure intensity line down, parallel to itself, by a distance of [math]\displaystyle{ (1-\alpha )\,\! }[/math]. Similarly, the current or instantaneous MTBF growth line is obtained by shifting the cumulative MTBF line up, parallel to itself, by a distance of [math]\displaystyle{ \tfrac{1}{1-\alpha }\,\! }[/math], as illustrated in the figure below.

Parameter Estimation

The Duane model is a two parameter model. Therefore, to use this model as a basis for predicting the reliability growth that could be expected in an equipment development program, procedures must be defined for estimating these parameters as a function of equipment characteristics. Note that, while these parameters can be estimated for a given data set using curve-fitting methods, there exists no underlying theory for the Duane model that could provide a basis for a priori estimation.

Graphical Method

The Duane model for the cumulative failure intensity is:

[math]\displaystyle{ {{\hat{{\bar{\lambda }}}}_{c}}=\frac{1}{b}{{T}^{-\alpha }}\,\! }[/math]

This equation may be linearized by taking the natural log of both sides:

[math]\displaystyle{ \ln \left( {{\hat{{\bar{\lambda }}}}_{c}} \right)=\ln \left( \frac{1}{b} \right)-\alpha \ln (T)\,\! }[/math]

Consequently, plotting [math]\displaystyle{ \hat{{\bar{\lambda }}}\,\! }[/math] versus [math]\displaystyle{ T\,\! }[/math] on log-log paper will result in a straight line with a negative slope, such that:

• [math]\displaystyle{ \ln \left ({\frac{1}{b}} \right)\,\! }[/math] is the y-intercept at [math]\displaystyle{ T = 1\,\! }[/math]
• [math]\displaystyle{ \frac{1}{b}\,\! }[/math] is the cumulative failure intensity at [math]\displaystyle{ T = 1\,\! }[/math]
• [math]\displaystyle{ \alpha\,\! }[/math] is the slope of the straight line on the log-log plot

Similarly, the corresponding MTBF of the cumulative failure intensity can also be linearized by taking the natural log of both sides:

[math]\displaystyle{ \begin{align} \hat{m_{c}}&=bT^{\alpha } \\ \ln \hat{m_{c}}&=\ln b+\alpha \ln T \\ \end{align}\,\! }[/math]

Plotting [math]\displaystyle{ \hat{m}\,\! }[/math] versus [math]\displaystyle{ T\,\! }[/math] on log-log paper will result in a straight line with a positive slope such that:

• [math]\displaystyle{ \ln{b}\,\! }[/math] is the y-intercept at [math]\displaystyle{ T = 1\,\! }[/math]
• [math]\displaystyle{ b\,\! }[/math] is the cumulative mean time between failure at [math]\displaystyle{ T = 1\,\! }[/math]
• [math]\displaystyle{ \alpha\,\! }[/math] is the slope of the straight line on the log-log plot

Two ways of determining these curves are as follows:

1. Predict the [math]\displaystyle{ {{\hat{{\bar{\lambda }}}}_{0}}\,\! }[/math] and [math]\displaystyle{ \hat{m}=\,\! }[/math] [math]\displaystyle{ \tfrac{1}{{{\hat{{\bar{\lambda }}}}_{0}}}\,\! }[/math] of the system from its reliability block diagram and available component failure intensities. Plot this value on log-log plotting paper at [math]\displaystyle{ T=1.\,\! }[/math] From past experience and from past data for similar equipment, find values of [math]\displaystyle{ {{\alpha }_{1}}\,\! }[/math], the slope of the improvement lines for [math]\displaystyle{ \hat{{\bar{\lambda }}}\,\! }[/math] or [math]\displaystyle{ \hat{m}\,\! }[/math]. Modify this [math]\displaystyle{ \alpha \,\! }[/math] as necessary. If a better design effort is expected and a more intensive research, test and development or TAAF program is to be implemented, then a 15% improvement in the growth rate may be attainable. Consequently, the available value for slope [math]\displaystyle{ \alpha \,\! }[/math], and [math]\displaystyle{ {{\alpha }_{1}}\,\! }[/math], should be adjusted by this amount. The value to be used will then be [math]\displaystyle{ \alpha =1.15{{\alpha }_{1}}.\,\! }[/math] A line is then drawn through point [math]\displaystyle{ {{\hat{{\bar{\lambda }}}}_{0}}\,\! }[/math] and [math]\displaystyle{ T=1\,\! }[/math] with the just determined slope [math]\displaystyle{ \alpha \,\! }[/math], keeping in mind that [math]\displaystyle{ \alpha \,\! }[/math] is negative for the [math]\displaystyle{ \hat{{\bar{\lambda }}}\,\! }[/math] curve. This line should be extended to the design, development and test time scheduled to be expended to see if the failure intensity goal will indeed be achieved on schedule. It is also possible to find that the design, development and test time to achieve the goal may be earlier than the delivery date or later. If earlier, then either the reliability program effort can be judiciously and appropriately trimmed; or if it is an incentive contract, full advantage is taken of the fact that the failure intensity goal can be exceeded with the associated increased profits to the company. A similar approach may be used for the MTBF growth model, where [math]\displaystyle{ {{\hat{m}}_{0}}=\tfrac{1}{{{\hat{{\bar{\lambda }}}}_{0}}}\,\! }[/math] is plotted at [math]\displaystyle{ T=1\,\! }[/math], and a line is drawn through the point [math]\displaystyle{ {{\hat{m}}_{0}}\,\! }[/math] and [math]\displaystyle{ T=1\,\! }[/math] with slope [math]\displaystyle{ \alpha \,\! }[/math] to obtain the MTBF growth line. If [math]\displaystyle{ \alpha \,\! }[/math] values are not available, consult the table below, which gives actual [math]\displaystyle{ \alpha \,\! }[/math] values for various types of equipment. These have been obtained from literature or by MTBF growth tests. It may be seen from the following table that [math]\displaystyle{ \alpha \,\! }[/math] values range between 0.24 and 0.65. The lower values reflect slow early growth and the higher values reflect fast early growth.

Sample values for the slope ( [math]\displaystyle{ \alpha )\,\! }[/math] for various equipment

Equipment		Slope([math]\displaystyle{ \alpha\,\! }[/math])
Computer system	Actual	0.24
	Easy to find failures were eliminated	0.26
	All known failure causes were eliminated	0.36
Mainframe computer		0.50
Aerospace electronics	All malfunctions	0.57
	Relevant failures only	0.65
Attack radar		0.60
Rocket engine		0.46
Afterburning turbojet		0.35
Complex hydromechanical system		0.60
Aircraft generator		0.38
Modern dry turbojet		0.48

2. During the design, development and test phase and at specific milestones, the [math]\displaystyle{ \hat{{\bar{\lambda }}}=\tfrac{1}{{\hat{m}}}\,\! }[/math] is calculated from the total failures and [math]\displaystyle{ T\,\! }[/math] values. These values of [math]\displaystyle{ \hat{{\bar{\lambda }}}\,\! }[/math] or [math]\displaystyle{ \hat{m}\,\! }[/math] are plotted above the corresponding [math]\displaystyle{ T\,\! }[/math] values on log-log paper. A straight line is drawn favoring these points to minimize the distance between the points and the line, thus establishing the improvement or growth model and its parameters graphically. If needed, linear regression analysis techniques can be used to determine these parameters.

Graphical Method Example

A complex system's reliability growth is being monitored and the data set is given in the table below.

Cumulative Test Hours and the Corresponding Observed Failures for the Complex System

Point Number	Cumulative Test Time(hours)	Cumulative Failures	Cumulative MTBF(hours)	Instantaneous MTBF(hours)
1	200	2	100.0	100
2	400	3	133.0	200
3	600	4	150.0	200
4	3,000	11	273.0	342.8

Do the following:

1. Plot the cumulative MTBF growth curve.
2. Write the equation of this growth curve.
3. Write the equation of the instantaneous MTBF growth model.
4. Plot the instantaneous MTBF growth curve.

Solution

1. Given the data in the second and third columns of the above table, the cumulative MTBF, [math]\displaystyle{ {{\hat{m}}_{c}}\,\! }[/math], values are calculated in the fourth column. The information in the second and fourth columns are then plotted. The first figure below shows the cumulative MTBF while the second figure below shows the instantaneous MTBF. It can be seen that a straight line represents the MTBF growth very well on log-log scales.
   
   Cumulative MTBF plot
   
   Instantaneous MTBF plot

   By changing the x-axis scaling, you are able to extend the line to [math]\displaystyle{ T=1\,\! }[/math]. You can get the value of [math]\displaystyle{ b\,\! }[/math] from the graph by positioning the cursor at the point where the line meets the y-axis. Then read the value of the y-coordinate position at the bottom left corner. In this case, [math]\displaystyle{ b\,\! }[/math] is approximately 14 hours. The next figure illustrates this.

   
   Cumulative MTBF plot for [math]\displaystyle{ b \approx 14\,\! }[/math] at [math]\displaystyle{ T=1\,\! }[/math]

   Another way of determining [math]\displaystyle{ b\,\! }[/math] is to calculate [math]\displaystyle{ \alpha \,\! }[/math] by using two points on the fitted straight line and substituting the corresponding [math]\displaystyle{ {{\hat{m}}_{c}}\,\! }[/math] and [math]\displaystyle{ T\,\! }[/math] values into:

   [math]\displaystyle{ \alpha =\frac{\ln \left( {{{\hat{m}}}_{{{c}_{2}}}} \right)-\ln \left( {{{\hat{m}}}_{{{c}_{1}}}} \right)}{\ln \left( {{T}_{_{2}}} \right)-\ln \left( {{T}_{_{1}}} \right)}\,\! }[/math]

   Then substitute this [math]\displaystyle{ \alpha \,\! }[/math] and choose a set of values for [math]\displaystyle{ {{\hat{m}}_{{{c}_{1}}}}\,\! }[/math] and [math]\displaystyle{ {{T}_{_{1}}}\,\! }[/math] into the cumulative MTBF equation, [math]\displaystyle{ {{\hat{m}}_{c}}=b{{T}^{\alpha }}\,\! }[/math], and solve for [math]\displaystyle{ b\,\! }[/math]. The slope of the line, [math]\displaystyle{ \alpha \,\! }[/math], may also be found from the linearized form of the cumulative MTBF equation, or :

   [math]\displaystyle{ \alpha =\frac{\ln \left( {{{\hat{m}}}_{c}} \right)-\ln (b)}{\ln (T)-\ln (1)}\,\! }[/math]

   Using the cumulative MTBF plot for the example, at [math]\displaystyle{ {{T}_{_{1}}}=200\,\! }[/math] hours, [math]\displaystyle{ {{\hat{m}}_{{{c}_{1}}}}=100\,\! }[/math] hours, and [math]\displaystyle{ {{T}_{_{2}}}=3,500\,\! }[/math] hours, [math]\displaystyle{ {{\hat{m}}_{{{c}_{2}}}}=300\,\! }[/math] hours. From the cumulative MTBF plot for [math]\displaystyle{ b=14\,\! }[/math] hours when [math]\displaystyle{ T=1\,\! }[/math], substituting the first set of values, [math]\displaystyle{ b=14\,\! }[/math] hours and [math]\displaystyle{ \ln 1=0\,\! }[/math], into the equation yields:

   [math]\displaystyle{ \begin{align} {{\alpha }_{1}}= & \frac{\ln (100)-\ln (14)}{\ln (200)-\ln (1)} \\ = & 0.3711 \end{align}\,\! }[/math]

2. Substituting the second set of values, [math]\displaystyle{ b=14\,\! }[/math] hours and [math]\displaystyle{ \ln 1=0,\,\! }[/math] into the equation yields:

   [math]\displaystyle{ \begin{align} {{\alpha }_{2}}= & \frac{\ln (300)-\ln (14)}{\ln (3,500)-\ln (1)} \\ = & 0.3755 \end{align}\,\! }[/math]

   Averaging these two [math]\displaystyle{ \alpha \,\! }[/math] values yields a better estimate of [math]\displaystyle{ \hat{\alpha }=0.3733\,\! }[/math].
3. Now the equation for the cumulative MTBF growth curve is:

   [math]\displaystyle{ {{\hat{m}}_{c}}=14\cdot {{T}^{\text{ }0.3733}}\,\! }[/math]

4. Using the following equation for the instantaneous MTBF, or

   [math]\displaystyle{ {{m}_{i}} = \frac{1}{1-\alpha }{{{\hat{m}}}_{c}},:\ \ \alpha \not{=}1 \,\! }[/math]

   The equation for the instantaneous MTBF growth curve is:

   [math]\displaystyle{ \begin{align} {{\hat{m}}_{i}}=\frac{1}{1-0.3733} \cdot {{14T}^{0.3733}} \end{align}\,\! }[/math]

   The above equation is plotted in the instantaneous MTBF plot shown in the example and in the cumulative and instantaneous MTBF vs. Time plot. In the following figure, you can see that a parallel shift upward of the cumulative MTBF, [math]\displaystyle{ {{\hat{m}}_{c}}\,\! }[/math], line by a distance of [math]\displaystyle{ \tfrac{1}{1-\alpha }\,\! }[/math] gives the instantaneous MTBF, or the [math]\displaystyle{ {{\hat{m}}_{i}}\,\! }[/math], line.
   
   Cumulative and Instantaneous MTBF vs. Time plot

Least Squares (Linear Regression)

The parameters can also be estimated using a mathematical approach. To do this, linearize the MTBF of the cumulative failure intensity by taking the natural log of both sides, and then apply least squares analysis. For example:

[math]\displaystyle{ \begin{align} \hat{m_{c}}&=bT^{\alpha } \\ \ln \hat{m_{c}}&=\ln b+\alpha \ln T \\ \end{align}\,\! }[/math]

For simplicity in the calculations, let:

[math]\displaystyle{ \begin{align} \ln ({{m}_{ci}})= & {{Y}_{i}} \\ \ln (b)= & a \\ \alpha = & c \\ \ln ({{T}_{i}})= & {{X}_{i}} \end{align}\,\! }[/math]

Therefore, the equation becomes:

[math]\displaystyle{ {{Y}_{i}}=\hat{a}+\hat{c}{{X}_{i}}\,\! }[/math]

Assume that a set of data pairs [math]\displaystyle{ ({{X}_{1}},{{Y}_{1}})\,\! }[/math], [math]\displaystyle{ ({{X}_{2}},{{Y}_{2}})\,\! }[/math],..., [math]\displaystyle{ ({{X}_{N}},{{Y}_{N}})\,\! }[/math] were obtained and plotted. Then according to the Least Squares Principle, which minimizes the vertical distance between the data points and the straight line fitted to the data, the best fitting straight line to this data set is the straight line [math]\displaystyle{ Y=\hat{a}+\hat{c}X\,\! }[/math] such that:

[math]\displaystyle{ \underset{i=1}{\overset{N}{\mathop \sum }}\,{{(\hat{a}+\hat{c}{{X}_{i}}-{{Y}_{i}})}^{2}}=\underset{(a,c)}{\mathop{min}}\,\underset{i=1}{\overset{N}{\mathop \sum }}\,{{(a+c{{X}_{i}}-{{Y}_{i}})}^{2}}\,\! }[/math]

where [math]\displaystyle{ \hat{a}\,\! }[/math] and [math]\displaystyle{ \hat{c}\,\! }[/math] are the least squares estimates of [math]\displaystyle{ a\,\! }[/math] and [math]\displaystyle{ c\,\! }[/math]. To obtain [math]\displaystyle{ \hat{a}\,\! }[/math] and [math]\displaystyle{ \hat{c}\,\! }[/math], let:

[math]\displaystyle{ F=\underset{i=1}{\overset{N}{\mathop \sum }}\,{{(a+c{{X}_{i}}-{{Y}_{i}})}^{2}}\,\! }[/math]

Differentiating [math]\displaystyle{ F\,\! }[/math] with respect to [math]\displaystyle{ a\,\! }[/math] and [math]\displaystyle{ c\,\! }[/math] yields:

[math]\displaystyle{ \frac{\partial F}{\partial a}=2\underset{i=1}{\overset{N}{\mathop \sum }}\,(a+c{{X}_{i}}-{{Y}_{i}})\,\! }[/math]

and:

[math]\displaystyle{ \frac{\partial F}{\partial c}=2\underset{i=1}{\overset{N}{\mathop \sum }}\,(a+c{{X}_{i}}-{{Y}_{i}}){{X}_{i}}\,\! }[/math]

Set those two equations equal to zero:

[math]\displaystyle{ \underset{i=1}{\overset{N}{\mathop \sum }}\,(a+c{{X}_{i}}-{{Y}_{i}})=\underset{i=1}{\overset{N}{\mathop \sum }}\,(\hat{{{Y}_{i}}}-{{Y}_{i}})=-\underset{i=1}{\overset{N}{\mathop \sum }}\,({{Y}_{i}}-\hat{{{Y}_{i}}})=0\,\! }[/math]

and:

[math]\displaystyle{ \underset{i=1}{\overset{N}{\mathop \sum }}\,(a+c{{X}_{i}}-{{Y}_{i}}){{X}_{i}}=\underset{i=1}{\overset{N}{\mathop \sum }}\,(\hat{{{Y}_{i}}}-{{Y}_{i}}){{X}_{i}}=-\underset{i=1}{\overset{N}{\mathop \sum }}\,({{Y}_{i}}-\hat{{{Y}_{i}}}){{X}_{i}}=0\,\! }[/math]

Solve the equations simultaneously:

[math]\displaystyle{ \begin{align} \hat{a}& =\frac{\underset{i=1}{\overset{N}{\mathop{\sum }}}\,{{Y}_{i}}}N-\hat\end{align}\,\! }[/math]

and:

[math]\displaystyle{ \hat{c}=\frac{\underset{i=1}{\overset{N}{\mathop{\sum }}}\,{{X}_{i}}{{Y}_{i}}-\tfrac{\left( \underset{i=1}{\overset{N}{\mathop{\sum }}}\,{{X}_{i}}\underset{i=1}{\overset{N}{\mathop{\sum }}}\,{{Y}_{i}} \right)}{N}}{\underset{i=1}{\overset{N}{\mathop{\sum }}}\,X_{i}^{2}-\tfrac{{{\left( \underset{i=1}{\overset{N}{\mathop{\sum }}}\,{{X}_{i}} \right)}^{2}}}{N}}\,\! }[/math]

Now substituting back [math]\displaystyle{ \ln ({{m}_{ci}})={{Y}_{i}},\,\! }[/math] [math]\displaystyle{ \ln (b)=a,\,\! }[/math] [math]\displaystyle{ \alpha =c\,\! }[/math] and [math]\displaystyle{ \ln ({{T}_{i}})={{X}_{i}},\,\! }[/math] we have:

[math]\displaystyle{ \hat{b}={{e}^{\tfrac{1}{n}\left[ \underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{m}_{ci}})-\alpha \underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{T}_{i}}) \right]}}\,\! }[/math]

where:

[math]\displaystyle{ \hat{\alpha }=\frac{\underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{T}_{i}})\ln ({{m}_{ci}})-\tfrac{\underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{T}_{i}})\underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{m}_{ci}})}{n}}{\underset{i=1}{\overset{n}{\mathop{\sum }}}\,{{\left[ \ln ({{T}_{i}}) \right]}^{2}}-\tfrac{{{\left( \underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{T}_{i}}) \right)}^{2}}}{n}}\,\! }[/math]

Example 1

Using the same data set from the graphical approach example, estimate the parameters of the MTBF model using least squares.

Solution

From the data table:

[math]\displaystyle{ \begin{align} \underset{i=1}{\overset{n}{\mathop \sum }}\,\ln ({{T}_{i}})&= & 25.693 \\ \underset{i=1}{\overset{n}{\mathop \sum }}\,\ln ({{T}_{i}})\ln ({{m}_{ci}})&= & 130.66 \\ \underset{i=1}{\overset{n}{\mathop \sum }}\,\ln ({{m}_{ci}})&= & 20.116 \\ \underset{i=1}{\overset{n}{\mathop \sum }}\,{{\left[ \ln ({{T}_{i}}) \right]}^{2}}&= & 168.99 \end{align}\,\! }[/math]

Obtain the value of [math]\displaystyle{ \hat{\alpha}\,\! }[/math] from the least squares analysis, or:

[math]\displaystyle{ \begin{align} \hat{\alpha }&=\frac{\underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{T}_{i}})\ln ({{m}_{ci}})-\tfrac{\underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{T}_{i}})\underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{m}_{ci}})}{n}}{\underset{i=1}{\overset{n}{\mathop{\sum }}}\,{{\left[ \ln ({{T}_{i}}) \right]}^{2}}-\tfrac{{{\left( \underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{T}_{i}}) \right)}^{2}}}{n}} \\ & = \frac{130.66-\tfrac{25.693\cdot 20.116}{4}}{168.99-\tfrac{{{25.693}^{2}}}{4}} \\ & = 0.3671 \end{align}\,\! }[/math]

Obtain the value [math]\displaystyle{ \hat{b}\,\! }[/math] from the least squares analysis, or:

[math]\displaystyle{ \begin{align} \hat{b}&={{e}^{\tfrac{1}{n}\left[ \underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{m}_{ci}})-\alpha \underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{T}_{i}}) \right]}} \\ & = {{e}^{\tfrac{1}{4}(20.116-0.3671\cdot 25.693)}} \\ & = 14.456 \end{align}\,\! }[/math]

Therefore, the cumulative MTBF becomes:

[math]\displaystyle{ \begin{align} \hat{m_{c}}&=bT^{\alpha } \\ &=14.456\cdot {{T}^{0.3671}} \\ \end{align}\,\! }[/math]

The equation for the instantaneous MTBF growth curve is:

[math]\displaystyle{ \begin{align} {{\hat{m}}_{i}}&=\frac{1}{1-\alpha }{{{\hat{m}}}_{c}},:\ \ \alpha \not{=}1 \\ &=\frac{1}{1-0.3671}(14.456){{T}^{0.3671}} \\ \end{align}\,\! }[/math]

Example 2

For the data given in columns 1 and 2 of the following table, estimate the Duane parameters using least squares.

Failure Times Data

(1)Failure Number	(2)Failure Time(hours)	(3)[math]\displaystyle{ \ln{T_i}\,\! }[/math]	(4)[math]\displaystyle{ \ln{T_i}^2\,\! }[/math]	(5)[math]\displaystyle{ m_c\,\! }[/math]	(6)[math]\displaystyle{ \ln{m_c}\,\! }[/math]	(7)[math]\displaystyle{ \ln{m_c}\cdot\ln{T_i}\,\! }[/math]
1	9.2	2.219	4.925	9.200	2.219	4.925
2	25	3.219	10.361	12.500	2.526	8.130
3	61.5	4.119	16.966	20.500	3.020	12.441
4	260	5.561	30.921	65.000	4.174	23.212
5	300	5.704	32.533	60.000	4.094	23.353
6	710	6.565	43.103	118.333	4.774	31.339
7	916	6.820	46.513	130.857	4.874	33.241
8	1010	6.918	47.855	126.250	4.838	33.470
9	1220	7.107	50.504	135.556	4.909	34.889
10	2530	7.836	61.402	253.000	5.533	43.359
11	3350	8.117	65.881	304.545	5.719	46.418
12	4200	8.343	69.603	350.000	5.858	48.872
13	4410	8.392	70.419	339.231	5.827	48.895
14	4990	8.515	72.508	356.429	5.876	50.036
15	5570	8.625	74.393	371.333	5.917	51.036
16	8310	9.025	81.455	519.375	6.253	56.431
17	8530	9.051	81.927	501.765	6.218	56.282
18	9200	9.127	83.301	511.111	6.237	56.921
19	10500	9.259	85.731	552.632	6.315	58.469
20	12100	9.401	88.378	605.000	6.405	60.215
21	13400	9.503	90.307	638.095	6.458	61.375
22	14600	9.589	91.945	663.636	6.498	62.305
23	22000	9.999	99.976	956.522	6.863	68.625
	Sum =	173.013	1400.908	7600.870	121.406	974.242

Solution

To estimate the parameters using least squares, the values in columns 3, 4, 5, 6 and 7 are calculated. The cumulative MTBF, [math]\displaystyle{ {{m}_{c}}\,\! }[/math], is calculated by dividing the failure time by the failure number. The value of [math]\displaystyle{ \hat{\alpha }\,\! }[/math] is:

[math]\displaystyle{ \begin{align} \hat{\alpha }&=\frac{\underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{T}_{i}})\ln ({{m}_{ci}})-\tfrac{\underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{T}_{i}})\underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{m}_{ci}})}{n}}{\underset{i=1}{\overset{n}{\mathop{\sum }}}\,{{\left[ \ln ({{T}_{i}}) \right]}^{2}}-\tfrac{{{\left( \underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{T}_{i}}) \right)}^{2}}}{n}} \\ & = \frac{974.242-\tfrac{173.013\cdot 121.406}{23}}{1400.908-\tfrac{{{(173.013)}^{2}}}{23}} \\ & = 0.6133 \end{align}\,\! }[/math]

The estimator of [math]\displaystyle{ b\,\! }[/math] is estimated to be:

[math]\displaystyle{ \begin{align} \hat{b}&={{e}^{\tfrac{1}{n}\left[ \underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{m}_{ci}})-\alpha \underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{T}_{i}}) \right]}} \\ & = {{e}^{\tfrac{1}{23}(121.406-0.6133\cdot 173.013)}} \\ & = 1.9453 \end{align}\,\! }[/math]

Therefore, the cumulative MTBF becomes:

[math]\displaystyle{ \begin{align} \hat{m_{c}}&= bT^{\alpha } \\ & =1.9453\cdot {{T}^{0.613}} \\ \end{align}\,\! }[/math]

Using the equation for the instantaneous MTBF growth curve,

[math]\displaystyle{ \begin{align} {{\hat{m}}_{i}}&=\frac{1}{1-\alpha }{{{\hat{m}}}_{c}},:\ \ \alpha \not{=}1 \\ & =\frac{1}{1-0.613}(1.945){{T}^{0.613}} \\ \end{align}\,\! }[/math]

Example 3

For the data given in the following table, estimate the Duane parameters using least squares.

Multiple Systems (Known Operating Times) Data}

Run Number	Failed Unit	Test Time 1	Test Time 2	Cumulative Time
1	1	0.2	2.0	2.2
2	2	1.7	2.9	4.6
3	2	4.5	5.2	9.7
4	2	5.8	9.1	14.9
5	2	17.3	9.2	26.5
6	2	29.3	24.1	53.4
7	1	36.5	61.1	97.6
8	2	46.3	69.6	115.9
9	1	63.6	78.1	141.7
10	2	64.4	85.4	149.8
11	1	74.3	93.6	167.9
12	1	106.6	103	209.6
13	2	195.2	117	312.2
14	2	235.1	134.3	369.4
15	1	248.7	150.2	398.9
16	2	256.8	164.6	421.4
17	2	261.1	174.3	435.4
18	2	299.4	193.2	492.6
19	1	305.3	234.2	539.5
20	1	326.9	257.3	584.2
21	1	339.2	290.2	629.4
22	1	366.1	293.1	659.2
23	2	466.4	316.4	782.8
24	1	504	373.2	877.2
25	1	510	375.1	885.1
26	2	543.2	386.1	929.3
27	2	635.4	453.3	1088.7
28	1	641.2	485.8	1127
29	2	755.8	573.6	1329.4

Solution

The solution to this example follows the same procedure as the previous example. Therefore, from the table shown above:

[math]\displaystyle{ \begin{align} \underset{i=1}{\overset{29}{\mathop \sum }}\,\ln ({{T}_{i}})= & 154.151 \\ \underset{i=1}{\overset{29}{\mathop \sum }}\,\ln {{({{T}_{i}})}^{2}}= & 902.592 \\ \underset{i=1}{\overset{29}{\mathop \sum }}\,\ln ({{m}_{c}})= & 82.884 \\ \underset{i=1}{\overset{29}{\mathop \sum }}\,\ln ({{T}_{i}})\cdot \ln ({{m}_{c}})= & 483.154 \end{align}\,\! }[/math]

For least squares, the value of [math]\displaystyle{ \alpha \,\! }[/math] is:

[math]\displaystyle{ \begin{align} \hat{\alpha }&=\frac{\underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{T}_{i}})\ln ({{m}_{ci}})-\tfrac{\underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{T}_{i}})\underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{m}_{ci}})}{n}}{\underset{i=1}{\overset{n}{\mathop{\sum }}}\,{{\left[ \ln ({{T}_{i}}) \right]}^{2}}-\tfrac{{{\left( \underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{T}_{i}}) \right)}^{2}}}{n}} \\ & = \frac{483.154-\tfrac{154.151\cdot 82.884}{29}}{902.592-\tfrac{{{(154.151)}^{2}}}{29}} \\ & = 0.5115 \end{align}\,\! }[/math]

The value of the estimator [math]\displaystyle{ b\,\! }[/math] is:

[math]\displaystyle{ \begin{align} \hat{b}&={{e}^{\tfrac{1}{n}\left[ \underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{m}_{ci}})-\alpha \underset{i=1}{\overset{n}{\mathop{\sum }}}\,\ln ({{T}_{i}}) \right]}} \\ & = {{e}^{\tfrac{1}{29}(82.884-0.5115\cdot 154.151)}} \\ & = 1.1495 \end{align}\,\! }[/math]

Therefore, the cumulative MTBF is:

[math]\displaystyle{ \begin{align} \hat{m_{c}}&=bT^{\alpha } & = 1.1495\cdot {{T}^{0.5115}} \end{align}\,\! }[/math]

Using the equation for the instantaneous MTBF growth,

[math]\displaystyle{ \begin{align} {{\hat{m}}_{i}}&=\frac{1}{1-\alpha }{{{\hat{m}}}_{c}},:\ \ \alpha \not{=}1 \\ & =\frac{1}{1-0.5115}(1.1495){{T}^{0.5115}} \end{align}\,\! }[/math]

Maximum Likelihood Estimators

L. H. Crow [17] noted that the Duane model could be stochastically represented as a Weibull process, allowing for statistical procedures to be used in the application of this model in reliability growth. This statistical extension became what is known as the Crow-AMSAA (NHPP) model. The Crow-AMSAA model, which is described in the Crow-AMSAA (NHPP) chapter, provides a complete Maximum Likelihood Estimation (MLE) solution to the Duane model.

Confidence Bounds

Least squares confidence bounds can be computed for both the model parameters and metrics of interest for the Duane model.

Parameter Bounds

Apply least squares analysis on the Duane model:

[math]\displaystyle{ \ln ({{\hat{m}}_{c}})=\ln (b)+\alpha \ln (t)\,\! }[/math]

The unbiased estimator of [math]\displaystyle{ {{\sigma}^{2}}\,\! }[/math] can be obtained from:

[math]\displaystyle{ {{\sigma }^{2}}=Var\left[ \ln {{m}_{c}}(t) \right]=\frac{SSE}{(n-2)}\,\! }[/math]

where:

[math]\displaystyle{ SSE=\underset{i=1}{\overset{n}{\mathop \sum }}\,{{\left[ \ln {{{\hat{m}}}_{c}}({{t}_{i}})-\ln {{m}_{c}}({{t}_{i}}) \right]}^{2}}\,\! }[/math]

Thus, the confidence bounds on [math]\displaystyle{ \alpha \,\! }[/math] and [math]\displaystyle{ b\,\! }[/math] are:

[math]\displaystyle{ C{{B}_{\alpha }}=\hat{\alpha }\pm {{t}_{n-2,\alpha /2}}SE(\hat{\alpha })\,\! }[/math]

[math]\displaystyle{ C{{B}_{b}}=\hat{b}{{e}^{\pm {{t}_{n-2,\alpha /2}}SE\left[ \ln (\hat{b}) \right]}}\,\! }[/math]

where [math]\displaystyle{ {{t}_{n-2,\alpha /2}}\,\! }[/math] denotes the percentage point of the [math]\displaystyle{ t\,\! }[/math] distribution with [math]\displaystyle{ n-2\,\! }[/math] degrees of freedom such that [math]\displaystyle{ P\{{{t}_{n-2}}\ge {{t}_{\alpha /2,n-2}}\}=\alpha /2\,\! }[/math] and:

[math]\displaystyle{ SE(\hat{\alpha })=\frac{\sigma }{\sqrt{{{S}_{xx}}}}\,\! }[/math]

[math]\displaystyle{ SE\left[ \ln (\hat{b}) \right]=\sigma \cdot \sqrt{\frac{\underset{i=1}{\overset{n}{\mathop{\sum }}}\,{{(\ln {{t}_{i}})}^{2}}}{n\cdot {{S}_{xx}}}}\,\! }[/math]

[math]\displaystyle{ {{S}_{xx}}=\left[ \underset{i=1}{\overset{n}{\mathop \sum }}\,{{(\ln {{t}_{i}})}^{2}} \right]-\frac{1}{n}{{\left( \underset{i=1}{\overset{n}{\mathop \sum }}\,\ln ({{t}_{i}}) \right)}^{2}}\,\! }[/math]

Other Bounds

Confidence bounds also can be obtained on the cumulative MTBF and the cumulative failure intensity:

[math]\displaystyle{ C{{B}_{{{m}_{c}}}}={{\hat{m}}_{c}}(t){{e}^{\pm {{z}_{\alpha }}\sqrt{Var\left[ \ln ({{{\hat{m}}}_{c}}) \right]}}}\,\! }[/math]

[math]\displaystyle{ \begin{align} {{[{{\lambda }_{c}}(t)]}_{L}}= & \frac{1}{{{[{{m}_{c}}(t)]}_{u}}} \\ {{[{{\lambda }_{c}}(t)]}_{U}}= & \frac{1}{{{[{{m}_{c}}(t)]}_{l}}} \end{align}\,\! }[/math]

When [math]\displaystyle{ n\,\! }[/math] is large, the approximate [math]\displaystyle{ 100(1-\alpha )%\,\! }[/math] confidence bounds for instantaneous MTBF are given by:

[math]\displaystyle{ \begin{align} {{m}_{i}}{{(t)}_{L}}= & \frac{{{[{{m}_{c}}(t)]}_{L}}}{{\hat{\beta }}} \\ {{m}_{i}}{{(t)}_{U}}= & \frac{{{[{{m}_{c}}(t)]}_{U}}}{{\hat{\beta }}} \end{align}\,\! }[/math]

and

[math]\displaystyle{ \lambda_{i}(t) = \frac {1}{m_{i}(t)}\,\! }[/math]

therefore, the confidence bounds on the instantaneous failure intensity are:

[math]\displaystyle{ \begin{align} {{[{{\lambda }_{i}}(t)]}_{L}}= & \frac{1}{{{[{{m}_{i}}(t)]}_{U}}} \\ {{[{{\lambda }_{c}}(t)]}_{U}}= & \frac{1}{{{[{{m}_{i}}(t)]}_{L}}} \end{align}\,\! }[/math]

Duane Confidence Bounds Example

Using the values of [math]\displaystyle{ \hat{b}\,\! }[/math] and [math]\displaystyle{ \hat{\alpha }\,\! }[/math] estimated from the least squares analysis in Least Squares Example 2:

[math]\displaystyle{ \hat{b}=1.9453\,\! }[/math]

[math]\displaystyle{ \hat{\alpha}=0.6133\,\! }[/math]

Calculate the 90% confidence bounds for the following:

1. The parameters [math]\displaystyle{ \alpha\,\! }[/math] and [math]\displaystyle{ b\,\! }[/math].
2. The cumulative and instantaneous failure intensity.
3. The cumulative and instantaneous MTBF.

Solution

1. Use the values of [math]\displaystyle{ \hat{b}\,\! }[/math] and [math]\displaystyle{ \hat{\alpha }\,\! }[/math] estimated from the least squares analysis. Then:

   [math]\displaystyle{ \begin{align} {{S}_{xx}}&=\left[ \underset{i=1}{\overset{n}{\mathop \sum }}\,{{(\ln {{t}_{i}})}^{2}} \right]-\frac{1}{n}{{\left( \underset{i=1}{\overset{n}{\mathop \sum }}\,\ln ({{t}_{i}}) \right)}^{2}} \\ & = 1400.9084-1301.4545 \\ & = 99.4539 \end{align}\,\! }[/math]

   [math]\displaystyle{ \begin{align} SE(\hat{\alpha })= & \frac{\sigma }{\sqrt{{{S}_{xx}}}} \\ = & \frac{0.08428}{9.9727} \\ = & 0.008452 \end{align}\,\! }[/math]

   [math]\displaystyle{ \begin{align} SE(\ln \hat{b})= & \sigma \cdot \sqrt{\frac{\underset{i=1}{\overset{n}{\mathop{\sum }}}\,{{(\ln {{T}_{i}})}^{2}}}{n\cdot {{S}_{xx}}}} \\ = & 0.065960 \end{align}\,\! }[/math]

   Thus, the 90% confidence bounds on parameter [math]\displaystyle{ \alpha \,\! }[/math] are:

   [math]\displaystyle{ C{{B}_{\alpha }}=\hat{\alpha }\pm {{t}_{n-2,\alpha /2}}SE(\hat{\alpha })\,\! }[/math]

   [math]\displaystyle{ \begin{align} {{\alpha }_{L}}= & 0.602050 \\ {{\alpha }_{U}}= & 0.624417 \end{align}\,\! }[/math]

   And 90% confidence bounds on parameter [math]\displaystyle{ b\,\! }[/math] are:

   [math]\displaystyle{ C{{B}_{b}}=\hat{b}{{e}^{\pm {{t}_{n-2,\alpha /2}}SE\left[ \ln (\hat{b}) \right]}}\,\! }[/math]

   [math]\displaystyle{ \begin{align} {{b}_{L}}= & 1.7831 \\ {{b}_{U}}= & 2.1231 \end{align}\,\! }[/math]

2. The cumulative failure intensity is:

   [math]\displaystyle{ \begin{align} {{\lambda }_{c}}= & \frac{1}{1.9453}\cdot {{22000}^{-0.6133}} \\ = & 0.00111689 \end{align}\,\! }[/math]

   And the instantaneous failure intensity is equal to:

   [math]\displaystyle{ \begin{align} {{\lambda }_{i}}= & \frac{1}{1.9453}\cdot (1-0.6133)\cdot {{22000}^{-0.6133}} \\ = & 0.00043198 \end{align}\,\! }[/math]

   So, at the 90% confidence level and for [math]\displaystyle{ T=22,000\,\! }[/math] hours, the confidence bounds on cumulative failure intensity are:

   [math]\displaystyle{ \begin{align} {{[{{\lambda }_{c}}(t)]}_{L}}= & 0.00106780 \\ {{[{{\lambda }_{c}}(t)]}_{U}}= & 0.00116825 \end{align}\,\! }[/math]

   For the instantaneous failure intensity:

   [math]\displaystyle{ \begin{align} {{[{{\lambda }_{i}}(t)]}_{L}}= & 0.00041299 \\ {{[{{\lambda }_{c}}(t)]}_{U}}= & 0.00045184 \end{align}\,\! }[/math]

   The following figures show the graphs of the cumulative and instantaneous failure intensity. Both are plotted with confidence bounds.
   
   
3. The cumulative MTBF is:

   [math]\displaystyle{ \begin{align} {{m}_{c}}(T)= & 1.9453\cdot {{22000}^{0.6133}} \\ = & 895.3395 \end{align}\,\! }[/math]

   And the instantaneous MTBF is:

   [math]\displaystyle{ \begin{align} {{m}_{i}}(T)= & \frac{1.9453}{1-0.6133}\cdot {{22000}^{0.6133}} \\ = & 2314.9369 \end{align}\,\! }[/math]

   So, at 90% confidence level and for [math]\displaystyle{ T=22,000\,\! }[/math] hours, the confidence bounds on the cumulative MTBF are:

   [math]\displaystyle{ \begin{align} {{m}_{c}}{{(t)}_{l}}= & 855.9815 \\ {{m}_{c}}{{(t)}_{u}}= & 936.5071 \end{align}\,\! }[/math]

   The confidence bounds for the instantaneous MTBF are:

   [math]\displaystyle{ \begin{align} {{m}_{i}}{{(t)}_{l}}= & 2213.1753 \\ {{m}_{i}}{{(t)}_{u}}= & 2421.3776 \end{align}\,\! }[/math]

   The figure below displays the cumulative MTBF.
   

   The next figure displays the instantaneous MTBF. Both are plotted with confidence bounds.

   

More Examples

Estimating the Time Required to Meet an MTBF Goal

A prototype of a system was tested with design changes incorporated during the test. A total of 12 failures occurred. The data set is given in the following table.

Developmental Test Data

Failure Number	Cumulative Test Time(hours)
1	80
2	175
3	265
4	400
5	590
6	1100
7	1650
8	2010
9	2400
10	3380
11	5100
12	6400

Do the following:

1. Estimate the Duane parameters.
2. Plot the cumulative and instantaneous MTBF curves.
3. How many cumulative test and development hours are required to meet an instantaneous MTBF goal of 500 hours?
4. How many cumulative test and development hours are required to meet a cumulative MTBF goal of 500 hours?

Solution

1. The next figure shows the data entered into RGA along with the estimated Duane parameters.
   
2. The following figure shows the cumulative and instantaneous MTBF curves.
   
3. The next figure shows the cumulative test and development hours needed for an instantaneous MTBF goal of 500 hours.
   
4. The figure below shows the cumulative test and development hours needed for a cumulative MTBF goal of 500 hours.
   

Multiple Systems - Known Operating Times Example

Two identical systems were tested. Any design changes made to improve the reliability of these systems were incorporated into both systems when any system failed. A total of 29 failures occurred. The data set is given in the table below.

Do the following:

1. Estimate the Duane parameters.
2. Assume both units are tested for an additional 100 hours each. How many failures do you expect in that period?
3. If testing/development were halted at this point, what would the reliability equation for this system be?

Developmental Test Data

Failure Number	Failed Unit	Test Time Unit 1(hours)	Test Time Unit 2 (hours)
1	1	0.2	2.0
2	2	1.7	2.9
3	2	4.5	5.2
4	2	5.8	9.1
5	2	17.3	9.2
6	2	29.3	24.1
7	1	36.5	61.1
8	2	46.3	69.6
9	1	63.6	78.1
10	2	64.4	85.4
11	1	74.3	93.6
12	1	106.6	103
13	2	195.2	117
14	2	235.1	134.3
15	1	248.7	150.2
16	2	256.8	164.6
17	2	261.1	174.3
18	2	299.4	193.2
19	1	305.3	234.2
20	1	326.9	257.3
21	1	339.2	290.2
22	1	366.1	293.1
23	2	466.4	316.4
24	1	504	373.2
25	1	510	375.1
26	2	543.2	386.1
27	2	635.4	453.3
28	1	641.2	485.8
29	2	755.8	573.6

Solution

1. The figure below shows the data entered into RGA along with the estimated Duane parameters.
   
2. The current accumulated test time for both units is 1329.4 hours. If the process were to continue for an additional combined time of 200 hours, the expected cumulative number of failures at [math]\displaystyle{ T=1529.4\,\! }[/math] is 31.2695, as shown in the figure below. At T = 1329.4, the expected number of failures is 29.2004. Therefore, the expected number of failures that would be observed over the additional 200 hours is [math]\displaystyle{ 31.2695-29.2004=2.0691\approx 2\,\! }[/math].
   
3. If testing/development were halted at this point, the system failure intensity would be equal to the instantaneous failure intensity at that time, or [math]\displaystyle{ \lambda =0.0107\,\! }[/math] failures/hour. See the following figure.
   

   An exponential distribution can be assumed since the value of the failure intensity at that instant in time is known. Therefore:

   [math]\displaystyle{ \begin{align} R(t)= & {{e}^{-\lambda t}} \\ = & {{e}^{-(0.0107)t}} \end{align}\,\! }[/math]

   Weibull++ can be utilized to provide a Reliability vs. Time plot which is shown below.

   

Using the Duane Model for Success/Failure Data

Given the sequential success/failure data in the table below, do the following:

1. Estimate the Duane parameters.
2. What is the instantaneous Reliability at the end of the test?
3. How many additional test runs with a one-sided 90% confidence level are required to meet an instantaneous Reliability goal of 80%?

Sequential Data

Run Number	Result
1	F
2	F
3	S
4	S
5	S
6	F
7	S
8	F
9	F
10	S
11	S
12	S
13	F
14	S
15	S
16	S
17	S
18	S
19	S
20	S

Solution

1. The following figure shows the data set entered into RGA along with the estimated Duane parameters.
   
2. The Reliability at the end of the test is equal to 78.22%. Note that this is the DRel that is shown in the control panel in the above figure.
3. The figure below shows the number of test runs with both one-sided confidence bounds at 90% confidence level to achieve an instantaneous Reliability of 80%. Therefore, the number of additional test runs required with a 90% confidence level is equal to [math]\displaystyle{ 42.2481-20=22.2481\approx 23\,\! }[/math] test runs.