BlockSim 8: State Change Triggers: Difference between revisions

From ReliaWiki
Jump to navigation Jump to search
No edit summary
(Redirected page to State Change Triggers)
 
(One intermediate revision by one other user not shown)
Line 1: Line 1:
==State Change Triggers ==
#REDIRECT [[State Change Triggers]]
=== Description ===
 
 
*Standard blocks can have state change triggers enabled by checking "Enable State Change Triggers (SCT)" property in a standard block/event properties.
*When a block has state change triggers enabled, it can be set to start each simulation in an OFF state. In this case, unless some event turns the block ON, the block will remain down for the entire simulation.
*The user can turn a block ON that is in an OFF state by adding state change trigger: If any item from these associated maintenance group(s) GOES DOWN then ACTIVATE this block; or if any item from these associated maintenance group(s) IS RESTORED then ACTIVATE this block.
*The user can turn a block OFF that is in an ON state by adding state change trigger: If any item from these associated maintenance group(s) GOES DOWN then DEACTIVATE this block; or if any item from these associated maintenance group(s) IS RESTORED then DEACTIVATE this block.
*This feature allows to mimic standby containers in COLD standby. However, blocks do not have to be in a parallel configuration so additional flexibility is allowed from traditional containers. In addition, maintenance groups can be associated with subdiagram blocks so that complex standby configurations can be modeled.
*State change triggesr also allow modeling dependent shut downs.
*Upon restoration of a Block, the user must select between one of the following State Upon Repair choices: Always On, Always Off, Default On Unless SCT Overridden, Default Off Unless SCT Overridden
 
=== Assumptions ===
 
*A block cannot trigger events on itself. For example if Block 1 belongs to MG 1 and Block 1 is set to be turned ON or OFF based on MG 1, this trigger is ignored.
*OFF_Events cannot trigger other events. This means that things cannot be turned OFF in cascade. For example, if block 1 going down, turns OFF block 2 and block 2 going down turns OFF block 3, a failure by block 1 will not turn OFF block 3. Block 3 would have to be associated with downing events of block 1, directly. The necessary for this restriction is that, OFF_Events triggers other events will have circular references problem. For example, four blocks A, B, C and D are in parallel. Block A belongs to MG A and initally it is ON. Block B belongs to MG B and its intial status is also ON. Block C belongs to MG C and its initial status is OFF. Block D belongs to MG D and its initial status is ON. A failure of Block A will turn OFF Block B. Then Block B will turn Block C ON and finally C will turn OFF Block D. However, if OFF_Event of Block D can turn Block B ON, and On_Event of Block B will turn Block C OFF, and OFF_Event of Block C will turn Block D ON, then there is a circular references problem. Thus we assume that OFF_Events cannot trigger other events.
*Blocks activated when they where OFF, cannot trigger events. This is to avoid circular references.
*Upon restoration states:
**Always On: Upon restoration, the block will always be on
**Always Off: Upon restoration, the block will always be off
**Default On Unless SCT Overridden: Upon restoration, the block will be on unless a request is made to turn this block off while the block is down and the request is still applicable at the time of restoration. For example, assume Block A's State upon repair is On unless SCT overridden. If a failure of Block B triggers a request to turn Block A off but Block A is down, when the maintenance for Block A is completed, Block A will be turned off if Block B is still down.
**Default off Unless SCT Overridden: Upon restoration, the block will be off unless a request is made to turn this block on while the block is down and the request is still applicable at the time of restoration
*Maintenances while block is off: Maintenances will be performed. At the end of the maintenance, "upon restoration" rules will be checked to determine the state of the block.
*Assumptions for phases: The state of a block (on/off) will be determined at the beginning of each phase based on the "Initial state" setting of the block for that phase.
*If there are multiple triggering requests putting on a block when it is down, only the latest one is considered. The latest request will cancel all requests before it. For example, Block A fails at 20 and is down until 70. Block B fails at 30 and Block C fails at 40. Block A have event trigger enable, it will be actived when Block B fails and it will be deactived when Block C fails. Thus from 20 to 70, at 30, Block B will put a request on Block A to turn it ON and at 40, Block C will put another request to turn it OFF. In this case, according to our assumption, requst from Block C at 40 will cancel the request from Block B at 30. Thus finally only requst from Block C will be considered. Thus Block A will be turned OFF at 70 when it is done with repair.
 
=== [http://www.reliawiki.org/index.php?title=Category:BlockSim_Examples&action=edit&redlink=1 Examples] ===

Latest revision as of 03:10, 2 August 2012

Redirect to:

Retrieved from "https://www.reliawiki.com/index.php?title=BlockSim_8:_State_Change_Triggers&oldid=28777"